I've seen this method used for movement and weight purposes as well as cardboard forms used for large build ups most of the guys commenting negatively have never seen a commercial job or been critiqued by anyone else other than a homeowner who know no better

Why He laid that reinforcement screen? Should ift up at least 1 cm! (otherwise useless!)

Garry Wright The mesh was pushed to the bottom. Where is the water supposed to go if he's pouring on plastic? This was painful to watch.

It doesnt seem to me be a self leveling compound, but I could be wrong, other than that it's ok

There's a few companys that make compund that can do up to 50mm in one pour nowadays to be fair. But i would never use it on a chipboard floor even with that feeble wire he put under it.

Hi sand and cement is better materials for that floor screeded but floor level compounds that the wrong materials for that job/ gib board is wet and starting damaged /finishing the floor is not good enough still rough and more cleaning up /prep works all good enough I think you are builder not a solid plastering thanks you very much you done the job but I am learning what you doing and you learn on my comments cheers brother

He didn't use self-levelling compound. He used Estrich (screed) which is exactly what you said but he definitely made it way too wet.

adangerousidiot, The end result is good, in the end I guess that's all that matters. I am a master tile-setter, I install tile marble, slate, and also terrazzo. Many newer installers do it this way, but I know the old ways of the trade. I mix the sand and cement myself, and I don't waste time with those leveling ties on the walls , and that is because of the cement and sand ratio I use has less water, and holds up. It is very difficult to write and explain my method here. I think he did a good job, even though he would go broke around my parts of the world with this method if it takes him more than 3 hours to do this job ( alone with no helper).

👍👏👏👏👏👏

NÃO AO COMUNISMO!!!!

x2 рулит

Это што за хуйню он тут делает ? И не песко бетон и не налевной. Нахуя ?

@@olegotdelka37 как раз стяжку и делает. глянь, что такое у него в мешке- baumit EB 42

Ano i vidna shto u vas v Rassii kacestva lutshe cem v Italii ...... nu vy i pridurki kaneshna ... 2 maliarnyh maeka 🤣🤣

@@mariocapuleti8618 Качество везде на самых разный уровнях. Придурков и у вас хватает, поаккуратнее с ярлыками.

Sascha Funk

Sascha Funk ggg

Sascha Funk yg

Wrong. It's probably the most UNPROFFESSIONAL attempt at levelling a floor that most builders have ever seen. There is so many mistakes it's not funny. Having enough money to buy a cheap laser level and a metal rail for your circular saw does not mean anything whatsoever about the quality of the result.

Have to agree with that Edward!

@@johncoops6897 maybe you are right with the unprofessional, I don't know. But you are wrong with the cheap metal rail for his circular saw. Have you ever seen how much this Festool saw and rail cost? Far to be cheap, it is top end tools.

@@totoleheros7506 My word "cheap" related to the laser level. Yes, I know that those rails are expensive, however my point is that no matter HOW much equipment you use and how much time you waste, this is not the correct way to do this task. It doesn't NEED to be level... in fact the entire point of such a wet area floor is to not have it level, but to have a fall towards a drain. Also, the final surface levels and flatness are sorted out by the tilers, who place the tiles on a 3 to 10mm thick bed of adhesive. They set the levels on the *tops+* of the tiles, not the bottom, and it doesn't matter whether the underfloor is perfectly smooth or flat. It's a total waste of time to create an underfloor at 0.1mm accuracy when the following trade doesn't even use that surface as a reference point.

@@tonygibbs9821 I'm pretty sure the title is the result of a bad automatic translation. Nobody wants to embarrass the guy. Some of the comments are unfortunate tho'.

The screed used is Baumit Estrick EB 42 which is a dry type of screed with only 4 liters / 35kg pack, not a self leveling liquid type, hence the decomposing when mixed and poured out like a selfe leveling liquid type of screed. This is printed on every package. When prepared properly the screed is described as a stiff to plastically/kneadable composition. If the majority of professionals is applying great and expensive material is such a way they should be thoroghly embarrassed. ch.baumit.com/produkte/estriche_boden/estriche/baumit-estrich-eb-42.html

This is translated from German and "Bad" means bathroom in German. It has nothing to do with bad work, he is dong just fine as you pointed out already.

How about guarantee..

@@arpadprp1778 no guarantee 🤗😂

How did u even think of this?but sooo correct!!! Pmsl

You know what I did? Sped it up to 2x. Awesome

Hahaha yes, that was my thought also. Had to go to the comment section to see if it was only me LOL

Or Benny Hill ... it only needed the music to make it so .... however, it was a good watch and I did learn a few tips

spierdalaj

Ну и логика у тебя, куклин. То ты кладеш сетку в середине, чтобы стяжка была одной целой, а потом демпфером хочешь разделить её на три части. В данном случае сетка отлично выполняет свои функции (предотвращает от разделения единой стяжки на несколько частей). Не обязательно класть сетку именно в центр стяжки, а желательно положить в нижней части.

Для сетки нужно 1-2см защитного слоя....

Клоун тот кто етого незнает)))))))))))))))))))))))))))))))))))))

бетон хорошо себя ведёт при зжатии,при растяжении для того,что бы он остался целым ему необходима арматура.Чем больший кусок стяжки (или бетона)есть-тем больший температурный коэфициент (растяжения-сжатия )на него воздействует. Разделение стяжки на зоны способствует сохранению целостности структуры сделанного изделия в более длинный период нежели дожить до зарплаты.

Мудрые советы, тот кто слышит тот поймёт.

As steel is great in tension and concrete is good for compression, the mesh would be best raised slightly off the floor on some little chips of stone, cement or 'chairs' so that it has a good protective layer of grout/concrete under the steel mesh to protect from corrosion but well down from the top surface.

Michael Hermann Das sehe ich genauso 😉

is das nicht fliesetrich der extra dünn ist um sich selbst zu nivellieren? die armierung scheint mir nur etwas tief, sonst alles richtig gemacht in meinen unfachmännischen augen.

ok vergiss was ich geschrieben hab, da fliest garnichts...

Da muss schon min. eine 15mm kommen! Das der Kerl sich nicht schämt so nen scheiß zu veröffentlichten, jeder richtige Fliesen oder Estrichleger hätte Ihm was erzählt.

Du hast recht. die nasse Pampe schwindet, da wird dir jeder Fliesenleger einen Rapport vom feinsten herauslassen. Die Ecken werden sich stellen, Risse auftreten.. Nacharbeiten kosten mehr, als der Estrich. Heimprojekt, mehr nicht.

Agreed. If he's goin to mix it so wet, then use self levelling compound then there's no need for a straight edge.

How to do it wrong......Jesús christ!

@@stephbhoy1 pretty sure that's self leveling compound with price pretty high much cheaper to go with this mix

Wrong, can't use self leveling compound it's too deep, you'd need a few hits at it, with wet gear like that, once levelled and going off it needs a steel trowel finish. But let's be honest he done it all wrong lol

@Glyn Owen I've never seen it, only selfleveling you have to mix with sharp sand to bulk it up. Also as the gear he's used is do wet the drying time would be over a month before a floor covering could be put down.

11qq

The process of screeding (leveling off by pulling a board across the wet concrete) was left a bit rough. It looks fairly level so it's ok for placing tiles. That's why there was no finish floating done. The few rough spots can be ground down with a diamond abrasive wheel so it's not big deal. In all fairness, it's a really awkward place to work. The lighting was crappy and you really need good light to see what you are doing. Plus, no one was there to help him. Also, he had poor tools to do the job. All in all, it's satisfactory considering what it's for. Basically, tiles are going on top of it so it's no big deal.

i assumed he was going to tile it.

Johnknoefler That's not really the point. Leveling a floor in this way is difficult and imprecise. Despite the initial use of a laser level it is not practical to achieve a good result by sort of winging the screeding in this way. Many years of practical floor tiling convince me that this is not an easy job in the best of circumstances, carpenters do not understand the tolerances needed, and a better system of perimeter boards to screed to are needed. Well done to the flooring guy for his job, but not overall a noteworthy system.

Honestly, his screed technique was a bit clumsy but it will pass.

johnknoefler I

That is critical indeed, now it doesn't have any function. Other point is that the concrete isn't mixed proper. The preparations were great! I guess he was learning as well.. Thanx for the video, I learned a lot!

@@s0012823 The underside is under tension when load is on top, so I don't think it has no function. That said I would also have lifted it.

@@metallitech The steel will corrode when it is too close to the bottom. I must be >2-3cm.

could have used bits of the mesh to lift it off the floor. Or bent the sides down like feet. Even a .5" would have been better.

you do realize millions of workers used to work with concrete for hundreds of years without respirators? not for 10 but whole working life, 20-30-40 years...

Jp you are good at predicting the future? so what are you doing here?

Hugo B.

smartboy

kzfaq.info/get/bejne/bLB1n7Ni0a6wm2g.html

Сетку правильнее класть вниз.

Сеть не должна быть против пленки, для этой цели есть пластмассовые «туфли», которые увеличивают высоту сетки до 3 см, а от стены должны иметь зазор 2,5-3 см.

Правильно

Да ещё и тонкую. МАК не больше тройки. Надо бы пятёрочку хотя бы, а ячейку можно и десять на десять под такой слой. Ну и ясно, что везде отступ нужен от края, от дна. Возле труб не надо

Зачем стока епкатся налил разгладить и всё делов, кусочек линолеума под угол мебели и всего делов то

allanpkr because if someone comes to my house or works on anything of mine and has that it’ll fucking do attitude they soon get shown the door

that will be any lowest point at the wall junction.lol

graham smith This is the point. If there is no drain, the floor can not be flat. It has to be up to 1cm (3/8 ") high by the walls, and lower in the center.

Agree this dude is the master

Todo bien y perfecto hasta antes de vaciar la mezcla, el acero nunca va hasta la base, debe quedar embebido en el concreto, con ese espesor debe quedar al menos a 25 cms con ayuda de calzas y/o "galletas", ayuda a dar fuerza al concreto y no quebrar al fraguar y luego usó pasta niveladora con exceso de agua, debió usar agua - arena y gruesos- cemento portland en proporciones adecuadas para formar concreto y haber hecho anclaje en paredes para no sobrecargar al piso de abajo si este es entrepaño, creo que lo es ya que tiene madera de baja calidad (aglomerada) pudiendo ser al menos triplay. Creo que va a instalar vitropiso sobre ese "vaciado" ya que le quedó como "firme" base. En fin, aunque la traducción del titulo quedó inadecuada por el traductor automático (por eso creó conflicto en los comentarios) si es criticable. Tiene muy buenas herramientas es indiscutible. Saludos desde México, edo. de Coahuila....Ing. Victor Hugo Jiménez

why?

@@mr.waffle9736 25000000 lbs of mix on a 1/2 plywood subfloor with 2ft on center floor joists

Cheapest quality, Just for joke. I think he build for sale, not for his

Probably on Beam and Block (look it up) with 100mm closed cell foam insulating layer overlayed with OSB. A common floor system. You'd be surprised how much weight that would support. Don't assume that floor is the same as you'd build.

+Thor The Northern I once saw a very dry piece of turd stranded in the desert, it has absolutely NO sense of humour.

Гуглоперводчик наверное чудит) Хорошо хоть не с китайского переводили)))

Смущенная - потому.что у него штаны постоянно сползают до бикини. :-)

Ей стыдно...

Возможно, совмещённая

verlegen/ положить (залить) ausgleichsschüttung /самовыравнивающаяся смесь

...only get "professionals" like you in the US and UK

Stfu mozzarella head

Alex psk fuck you to you piece of shit!

@@cristomario9118 this are true german "professionals". btw. great idea but poor details.

È un pasticcione.

Kkkkk very good!

Prakticna zena

This Guy did not a nice Job, sry.... My English is a little bit poor to explain - I´ve seen so many mistakes in this Vid. Many of planning his work, much more of doing it! But his worst Case is the among of water im "Estrichbeton"! Lightconcrete? No Matter, there a lot of concrete-mixes out. After 40+ years, i think U know this. where Do you come from? I´m from germany, we have a rule for every nails, you want to bring in..... We are the founders of clean-diesel ;-)))) Friendly Regards, Philipp

@@philipp3771 plan good less work and less error....

You can't scrimp when it comes to floor, it's a very permanent part of the build and this is just unprofessional and shoddy and will cost more money to repair after when it needs latexing

@@specialistscreeding6600 Why do you need repair? (Brick/concrete building has this type of floor in Europe and I never heard in my life any repairing about this.)

@@KugleeKuglee if I done a job like this I wouldn't be in business longer than a day. It's terrible, lumpy and needs layering or a tiler wouldn't go near it

nein, wieso?

Hängt vom Lastfall ab.

Stimmt, da unten macht sie überhaupt keinen Sinn. 1/3 Überdeckung. Entweder oben oder unten. So hätte der gute Mann einen 100€ Schein in die (zu dünne) Brühe werfen können, wäre genauso sinnvoll.lol.

In der Mitte ist die statische Nulllinie, also ist da die Armierung weggeschmissenes Geld. Sie muß ins untere Drittel, dort treten die Zugkräfte auf.

In dem Video ist einiges nicht nach der anerkannten Regel der Technik gemacht worden. 1. Randstreifen tackern ist ok, aber man sollte an die Schallübertragung denken. Dann sollte man diese nach dem verlegen der Fliesen erst abschneiden. 2.Dämmung nicht versetzt verlegt! 3. AKS Gitter zu tief und zu nah an der Wand ( man sollte etwas Luft lassen)!

Amen. There's so many things wrong I don't even know where to start

even googled it up... well... I'm dumb....

а вот и нет, все правильно, под стяжкой не прочное основание и нижнее армирование работает на растяжение. На такой площади стяжку не порвет, если смесь правильная конечно

@@McKarabas Я бы с вами согласился при условии что арматура была в стяжке, а так... стяжка лежит на арматуре... Проверено временем, СНиП... Опираюсь на многолетний опыт.

И сколько вы за много лет армированных стяжек демонтировали? )) Раствор неизбежно под сетку затечет, ее зачастую вообще наверх поднимает если не закрепить. Вы не путайте те обстоятельства, когда сетка закладывается для распределения напряжений в самой стяжке, здесь задача другая, распределить нагрузку которая передается сверху.

@@McKarabas Я с 1989г на стройке, начинал с рабочего, 11 лет руковожу ст.комп....вы думаете я считал сколько?))) При условии, что основание не жесткое, требуется сформировать плиту, а не жесткий подстилающий слой для распределения нагрузки. В данном случае распределение нагрузки возложено на тепло (вибро) -изоляционный слой, а при наличии таких слоев требуется формировании жесткого основания (не путать с подстилающим слоем), с армированием в нижнем слое на растяжение т.к. остается вероятность прогиба, при чем не зависимо на каком основании формируется "пирог"... Поднимет арматуру или нет...вот, для чего нужно играть в эту лотерею, когда можно установить уровень залегания? Зачастую поднимает арм. при вибрировании и то не равномерно, а тут...где-то поднимет, где-то нет...по этому я и констатировал, что армирование для галочки и расхода бюджета...

Всё работает, армирование в низу так как держит всю стяжку которая сверху. Тем более что пару сантиметров в местах под стяжку цемент заходит.

Vor allem wird der Randstreifen geklebt. Schallbrücken in dieser Größenordnung durch die Tackernadeln , gehen in einem Mehrfamilienhaus never ever.lol.

EvntlLPer .

Voralm hat er den Randstreifen mit den laser angebracht und mus ihn den noch kürzen omg

und zu guter letzt liegt das aks gitter viel zutief, das gehört ins obere drittel.

Ich habe mich köstlich amüsiert wie dieser Unwissender sich abgequält hat. Echt lustig. Der hat fast alles falsch gemacht was man wirklich falsch machen kann.

I'm from Poland and i have problem too

Nor me.....

5 inches of mud over suspended plywood for no reason.

i am turkish even i couldnt get it

The title is Hungarian but this worker is not sure :)