Flysky FSI6X Bluetooth Mod for Telemetry Mirror with Open TX ExpressLRS using Bluetooth HC05 Module

Рет қаралды 8,533

Күн бұрын

#Flysky #FSI6X #OpenTX
In this video we take a look at how to install a Bluetooth HC 05 Module in the Flysky FSI6X radio flashed with Open Tx firmware + ExpressLRS
Telemetry Mirror
The Serial Port firmware will be available once ExpressLRS 3.0 is released.
so stay tuned until then.
Serial Communicator software - sourceforge.net/projects/serc...
Telemetry Viewer -
00:00 - Intro
00:26 - HC05 Bluetooth Module
01:46 Wiring Bluetooth Module
03:27 AT Commands
10:25 Firmware Update
11:50 Serial Port Option
12:28 Pairing Bluetooth Module
13:20 Radio Telemetry Settings
13:45 Telemetry Viewer App
16:02 Install BT Module in Radio
Thanks for watching
Subcribe for more videos!

Пікірлер: 69

@SeansLittleBayofHorrors Жыл бұрын

Thanks for giving us budget minded pilots some awesome options and such great walk-throughs!!!

@RakishRc Жыл бұрын

Thanks for watching! 👍 Kudos to developers

@danieldewindt3919 3 ай бұрын

Grate tutorial. Thanks for sharing 🙂

@fishballfpv9063 2 жыл бұрын

bru i thought im done with my mods on my i6x but i guess im not..thanks for the tutorial..sending love from PH..

@RakishRc 2 жыл бұрын

Thanks for watching 👍

@islandrc-duke1972 2 жыл бұрын

Great mod and information, great video my friend

@RakishRc 2 жыл бұрын

Thanks!! 👍

@sujanbadikana 2 жыл бұрын

You r just🔥

@unpocodetodofuerzayhonor6061 2 жыл бұрын

👏🏼🙌

@stelic9515 2 жыл бұрын

Thanks

@RakishRc 2 жыл бұрын

You're welcome 👍

@beefybeef1326 Жыл бұрын

This is awesome!. How have you connected the Express LRS module to the remote?

@davidkender4660 8 ай бұрын

Great Info - Thank you. Is the pa9 pad connected to any of the pins at the Trainer Port on the back of the transmitter?

@alexandrugroza839 2 ай бұрын

@RakishRc HC-05 is now connected Enter AT commands: OK +ROLE:0 OK +UART:115200,0,0 OK I Have verified and it is good.. I think this is ratter a radio issue. I measured continuos 3.3v on PA9 pin, wich i suppose has to send a pwn signal or some something else ratter than high 3.3v

@akshayharidas1235 Жыл бұрын

Is there any eay to configure hc05 with out ftdi adapter

@GKCcisco Жыл бұрын

Hey great video as always! Will this work without the express Lrs module? I am using ibus telemetry with the fsia6b

@RakishRc Жыл бұрын

At the moment only elrs telemetry is transmitted. Flysky telemetry mirror doesn't work yet but it could be implemented in future

@GKCcisco Жыл бұрын

@@RakishRc Thank you!

@RCwithSohel Жыл бұрын

How to do this same thing in radiomaster tx12?

@kunyongchen3156 2 жыл бұрын

Thanks for the tutorial! I just a noob in RC model , also try to elrs, but don't know how to wire up the elrs receiver to the origin receiver. Is that ppm or something like sbus signal regulation to transfer the signal ?

@RakishRc 2 жыл бұрын

For elrs it's the crossfire protocol via tx2 pad on radio

@madladdan 11 ай бұрын

Does this work with the radiomaster tx12 mk1 too?

@shivufpv6248 Жыл бұрын

Can we connect to mission planner?

@nmrlab3807 2 жыл бұрын

@Rakish Rc Thanks for the tutorial. Do you know which is the pin that outputs SBUS on FSI6X? I am trying to use SBUS than PPM to connect my SIYI FM30 external module to FSI6X.

@RakishRc 2 жыл бұрын

Currently sbus output is available but will be available soon i guess for external modules.

@yaimem 4 ай бұрын

how did you change the firmware of your fsi6 to look like that? i wanna do it too

@Indonesia01ian 6 ай бұрын

Hi, My remote is Radiomaster Pocket ELRS Can I follow your step? I am really new in RC And electronic Thank you

@TodorDimitrov-dw7xu 2 ай бұрын

Hi! The switch setting of the original firmware could be set up at 120% and the servo motors also have larger stroke in the original firmware. How can I set up more than100% in opentx to get 120 % because it is insufficient for correct move of the boat.

@pratieks Ай бұрын

Is it possible to use an HC05 bluetooth module to establish a bidirectional (control+telemetry) link? One application would be to use bluetooth connection with your laptop to run a simulator like PicaSim. Maybe also to transmit control signal to your ground station when using Ardupilot to control pan and tilt FPV camera gimbal so that a head tracker signal could be sent first from your transmitter to the ground station, then from your ground station to the craft receiver via Mavlink.

@nmrlab3807 2 жыл бұрын

@Rakish Rc I am thinking of adding the HC05 as well, but curious to know if you have experienced a noticeable power consumption because the Bluetooth module is always running?

@RakishRc 2 жыл бұрын

I use a 2s 1000mah lipo so it doesn't matter. But I've also used with AA batteries and they lasted for good time so Bluetooth module doesn't really affect the battery life that much

@nmrlab3807 2 жыл бұрын

@@RakishRc Thanks a lot. I'll add the module then.

@nmrlab3807 2 жыл бұрын

I have connected the HC05 to the FS-i6x (updated to 1.6.0 firmware), the telemetry output is enabled in INAV and also on the TX set to telemetry mirror. I can connect the HC05 to the telemetry viewer app but there is no data obtained from the flight controller. On the TX, I am able to see ten sensors outputs (Not sure why GPS is NOT listed within my sensors on the TX). The HC05 RX is connected to PA9, and I am using 5V from the TX pad and the GND2 pin. My HC05 module has a blue led lighting up aside from the red the led. Any suggestions to fix this issue? Thanks.

@romkas7718 2 жыл бұрын

Hello. Is it possible to record the drone's GPS path using this phone app ?

@RakishRc 2 жыл бұрын

Yes

@Dr_Khanz 2 жыл бұрын

Bro.. im thinking to start fpv .. haven't bought any controller.. should i buy a fsi6x or go directly to the best one like the new zorro?

@RakishRc 2 жыл бұрын

Buying a latest radio like Zorro or tbs mambo or radio master tx12 would be a wise choice.

@kharismayogapratama2994 2 жыл бұрын

Apakah hal ini bisa untuk jumper t12 ?karena sangat membutuhkannya !

@donavansnyders2429 2 жыл бұрын

Hi. I have used hm-10 Ble module and can connect my phone using a Bluetooth serial monitor, and see data streaming. The data changes slightly when the receiver connects. Is there a telemetry app that can read Ble module

@RakishRc 2 жыл бұрын

Did you use telemetry viewer app?

@ravigujjar956 11 ай бұрын

Is this working with internal afsh2a protocol without elrs

@RakishRc 11 ай бұрын

No it's only supported for elrs telemetry.

@alexandrugroza839 2 ай бұрын

Hy, i have configured and wired the HC-05 same way as you did, enabled telemetry mirror and set baudrate on radio to 400k, then 1.8M then 115200.. but none of them actually sent me any data. The bluetooth connection is working, i can connect to the device, but i don't get data in "Telemetry viewer" on android, nor in Mission planner inav. ELRS Telemetry is working betwen the tx and the rx, i get all sensors, and i can view them on my slysky fsi6x screen. Do i need a special LUA script to enable telemetry mirror to do something ? I have measured at some point that pa9 pin, and i got 3.3v on the multimeter, that is wired to hc05 rx pin.

@RakishRc 2 ай бұрын

Mostly like the hc05 configuration settings are not saved correctly. Make sure that the baud rate for the hc05 is set to 115200 and check if it's saved with the AT+UART? Command. If it's correct and still not transmitting data check the ground connection between hc05 and the radio. Lastly also check if the tx and Rx wires are connected correctly between the radio pins and module.

@alexandrugroza839 2 ай бұрын

@@RakishRc HC-05 is now connected Enter AT commands: OK +ROLE:0 OK +UART:115200,0,0 OK I Have verified and it is good.. I think this is ratter a radio issue. I measured continuos 3.3v on PA9 pin, wich i suppose has to send a pwn signal or some something else ratter than high 3.3v

@rcboat58 Ай бұрын

@@alexandrugroza839 hi, are you fixed your issue with telemetry mirror? I have a same, there is no data on PA9 pin (FS-i6x transmitter with Open I6X v1.11.1 firmware + HC-05) EDIT: I made downgrade fw to v.1.10.0 and AUX_UART started working.

@alexandrugroza839 Ай бұрын

@@rcboat58 hy.. nope, no update, no more answers on github, nothing new to help with my problem..

@alexandrugroza839 Ай бұрын

@@rcboat58 ok thanks for the tip.. i guess i will have to try! are any bugs or less features in the downgraded version?

@staydown.normal5323 Жыл бұрын

is there any way i can attach the bluetooth module to my drone so the drone sends telemetry so i can use it like remote id

@RakishRc Жыл бұрын

Which flight controller are you using? It's possible provided the flight controller and the configuration software support it. Mission planner has this option

@staydown.normal5323 Жыл бұрын

@@RakishRc i am using a matek wse f411 and inav 2.6.1 adrupilot show me going up when i go down .....its wrong... left and right it perfect

@RakishRc Жыл бұрын

@@staydown.normal5323 pitch stick need to be inverted. Atleast with adrucopter i have to reverse the pitch channel else it's inverted by default

@staydown.normal5323 Жыл бұрын

@@RakishRc so i will have to invert my rc controller out.? then i will have to invert inav to so it dose not invert my plane sticks...yeah? then adruplilot should show the plane going up for up and down for down...?

@staydown.normal5323 Жыл бұрын

@@RakishRc how do i do this

@wingsmh27 2 жыл бұрын

Ooo no i have i6 need to buy i6x for such mod

@RakishRc 2 жыл бұрын

For fsi6 take a look at erfly6 firmware - kzfaq.info/get/bejne/aMenqpuY3LiYpHU.html It also supports elrs and Bluetooth mod could be implemented.

@fishingforfun3294 Жыл бұрын

flysky fs-i6 can i do it?

@prajjwalkarki1426 Ай бұрын

As i know telemetry is only on fs-i6x😢

@srinivasreddypamulapati5608 2 жыл бұрын

Sir did you directly connected the 2s battery to the transmitter...I'm thinking of modding my transmitter battery and I'm not getting any correction info about the max input voltage the transmitter can withstand...is it safe to use a fully charged 2s since we are giving 8.4 volts i have doubt about that

@RakishRc 2 жыл бұрын

So I've been using a 2s lipo only to power my fsi6x. Have had no problems yet. There are many more users directly using a 2s lipo without any issues. However like you said there is no official voltage specifications about the regulator so there's always a chance of things smoking up. If you have a latest fsi6x board from 2017 then you should be fine using a 2s. 👍

@srinivasreddypamulapati5608 2 жыл бұрын

@@RakishRc thankyou sir