Ford 2.0 How to Remove Timing Cover

Рет қаралды 10,047

Жыл бұрын

Ford 2.0 How to Remove Timing Cover
In this video I have a leaking timing cover on this non turbo Ford and cannot just remove the timing cover without a special tool kit and following a specific procedure. Well this engine does not have a key way for the harmonic balancer and if you remove the balancer without the proper procedure you will end up with one of several issues. Worst thing would be bent valves, Crank no start, check engine light or drivability issues. It is not an incredibly difficult job so come with me and let me show you how to get this done without any issues.
OMT Tool Timing set amzn.to/3TgeGvE
HERE IS A LINK TO MY AMAZON INFLUENCER PAGE WHERE I LINK SOME OF THE PRODUCTS I RECOMMEND.
www.amazon.com/shop/nutsbolts...
The Amazon links are a paid partnership with Amazon.
Find me here:
beacons.ai/nutsnbolts

Пікірлер: 26

@billbeckett1021 Жыл бұрын

Two great non diesel engines vids in a row! I think there are techs who get it and those who pretend to get it. Tone gets it and has no attitude at all. He is willing to share his knowledge with the world. Tone is most definitely the best at what he does. He is an example of how to be a master technician. Excellent job Tone!

@NutsandBoltswithTone Жыл бұрын

Bill you truly are a wonderful human, thank you for the continued support. I made this video because I have made the mistake of taking this a part not knowing about the tools needed because I mean hey it is just a timing cover. I have seen several techs take this a part and put it back together 2 or 3 times until getting it right. Thank you for watching.

@alejandroespejel9759 8 күн бұрын

I wish you do one video 2015 Ford CMax Hybrid ! Thanks for the video Helping a lot

@jonathansims3377 28 күн бұрын

nice video over all. if the cam is locked from rotating and the timing chain is on......is the crank not locked as well? are we holding back up just to keep from damaging the timing components and not necessarily to keep the engine from spinning?

@NutsandBoltswithTone 20 күн бұрын

The crank should be up against a pin in the block, this pin only keeps it from turning one direction though. You are keeping the engine in time, because then you have to get balancer on for the crank sensor

@cesarchiang4941 2 ай бұрын

So I'm fucked if I took it all apart before using any of these tools?

@NutsandBoltswithTone 2 ай бұрын

Message me on Instagram I can help walk you through seeing it up

@felixmejia7589 6 ай бұрын

Hey great video. I'm replacing the timing cover on a 2015. What is the website you used for the images.

@NutsandBoltswithTone 6 ай бұрын

Hey there I use Alldata for repair info, we have full subscription that we use for all vehicles but you can purchase a single vehicle subscription and has all the pictures, torque specs and procedures for the vehicle. Thanks for watching, hit me up on Instagram if you need anymore help.

@adamgarms5101 5 ай бұрын

what website are you using that shows thoughs specs and procedures in detail?

@NutsandBoltswithTone 5 ай бұрын

We use All data U can buy a single vehicle subscription. Thanks for watching

@caraddictmotorsports 8 ай бұрын

What is book hour for this job? Great video btw.

@NutsandBoltswithTone 8 ай бұрын

I am actually not sure, and I am now hurt with an ankle injury. I will not be back in the shop for at least 3 months. it is less then 8 hours I believe. Thanks for watching.

@caraddictmotorsports 8 ай бұрын

@NutsandBoltswithTone based on a Google search, I guessed it to be about 7.5bh. Thanks again and I wish you a speedy recovery.

@NutsandBoltswithTone 8 ай бұрын

@caraddictmotorsports sweet I was close. Thank you brotha and good luck. Hit me up on Instagram if you have any questions

@user-cz5fj1bx4b 4 ай бұрын

Where can I buy the timing tool kit at

@NutsandBoltswithTone 4 ай бұрын

Here is a link to get one. amzn.to/3TgeGvE Thanks for watching

@richardstrongarm1935 8 ай бұрын

Can I bring mine to you for the same repair? Im in serious need for this repair to be done properly.

@NutsandBoltswithTone 8 ай бұрын

Absolutely. Message me on Instagram and we can chat. I'm in Sacramento CA. Thanks for watching

@REVNUMANEWBERN Ай бұрын

@@NutsandBoltswithTone Dang, too bad you're in Ca, I'm in Florida & I simply DON'T trust getting my car in hock with someone who will want to rip me off

@NutsandBoltswithTone Ай бұрын

Are you near miami lakes? I know a shop there i really trust?@REVNUMANEWBERN

@REVNUMANEWBERN Ай бұрын

@@NutsandBoltswithTone No unfortunately I'm in North Central Florida, QUICK question, I have around 130,000 miles on mine, bought new, it APPEARS the engine mount bolts INTO the timing cover, is that correct? I had my engine mount replaced maybe 40K latter than it should of been, 1) do you think that vibration of a worn out engine mount could of caused damage TO the timing cover or loosened the mount bolts to the block? 2) OR the installer did damage TO the cover installing the engine mount that would cause the leak? 3) Worse case scenario do you think I should buy a factory timing cover IN ADVANCE of having the leak repaired in case I need a new one? 4) Have you ever seen a issue where the cover would need to be repaired?