Ford 5.4 2V Timing Chain Replacement

Рет қаралды 26,848

Жыл бұрын

In this highly detailed video, I'm tackling the timing chain replacement, along with the timing chain tensioners, timing chain guides, and crank sprocket in our Ford 5.4 liter 2 valve motor. This repair is essential to eliminate the dreaded timing chain tensioner failure and the accompanying startup noise for which this motor is famous. I'll guide you step by step through the entire process; even providing torque specifications. A critical aspect I'll cover is aligning your timing marks. Proper alignment is crucial to prevent engine damage and I'll walk you through the process, ensuring you can confidently align those marks.
I chose to use the kit from Melling. The kit's part number is 3-391S, and it contains all the necessary components to ensure a smooth and successful repair.
Links to videos in this series (as they become available):
Part 1: Ford 5.4 2V Knocking Sound, Removal, Teardown
• Ford 5.4 2V Build - Kn...
Part 2: Ford 5.4 2V Piston & Deck Cleaning - Preparation For Head Installation
• Ford 5.4 2V Build - Pi...
Part 3: Ford 5.4 Liter 2V Block & Parts Painting - Preparation For Assembly
• Ford 5.4 2V Build - Bl...
Part 4: Ford 5.4 2V Build - Rear Main Seal Replacement
• Ford 5.4 2V Build - Re...
Part 5: Ford 5.4 2V Build - CalVan Tools 38900 Spark Plug Repair Tool Kit Instructions
• CalVan Tools 38900 Spa...
Part 6: Ford 5.4 2V Build - Melling M176HV Oil Pump Install
• Melling M176HV Oil Pum...
Part 7: Ford 5.4 2V Build - Head Gasket Replacement
• Ford 5.4 2V Head Gaske...
Part 8: Ford 5.4 2V Build - Oil Filter Adapter Gasket Replacement
• Ford 5.4 2V Oil Filter...
Part 9: Ford 5.4 2V Water Pump Replacement
• Ford 5.4 2V Water Pump...
As an Amazon Affiliate I earn from qualifying purchases.
Links to products used in this video series so far:
Melling Timing Chain Kit: amzn.to/3WbT9Fi
Updated Ford Fastener Part#: W709818-S437
OTC Camshaft Positioning Tool: amzn.to/42OeffI
Camshaft Holding Tool: amzn.to/3odPwlG
Crankshaft Positioning Tool: amzn.to/41JEwug
Motorcraft Water Pump: amzn.to/3MOL9HK
Motorcraft Tube Assembly: amzn.to/41EIkNL
Heater Return Tube Part #: F85Z-18663-BA (not on Amazon)
Fel-Pro Oil Filter Adapter Gasket: amzn.to/3ZyFl8c
Oil Pressure Sending Unit: amzn.to/3zhg6MF
Fel-Pro LH Head Gasket: amzn.to/3FNYRGJ
Fel-Pro RH Head Gasket: amzn.to/3z2YBQf
Fel-Pro Head Bolts: amzn.to/3FOyAbf
Cal-Van Tools 38900 Ford Triton Tool Kit: amzn.to/42mH2rY
Time-Sert 6020 Thread Locker & Sealer: amzn.to/42gwRVF
JB Weld 8265S Epoxy: amzn.to/3Tofhe8
Permatex Anti-Sieze Lubricant: amzn.to/3yP1rYM
AutoLite XP103 Soark Plug 4pk: amzn.to/3FqzcDC
Fel Pro Rear Main Seal - amzn.to/3LfAtRz
Ford Slinger - amzn.to/3T4TFUf
Permatex Ultra Black Gasket Maker - amzn.to/3J0zwdi
3M Roloc 2 inch disc 120gr - amzn.to/3ZGnj3Y
2 Inch disc holder - amzn.to/3kI83oF
3M Scotch-Brite pads - amzn.to/3IRpTxm
Lisle 52000 Razor Blade Scraper - amzn.to/3kLx02w
Plastic Razor Blades - amzn.to/3KVxNbY
3M Particulate Respirator - amzn.to/3Zbcbwl
Milwaukee Cordless Drill Kit - amzn.to/3SQExd4
Hopkins Drip Tray - amzn.to/3y8pHoL
Kimo 3/8" Electric Ratchet: amzn.to/3JEc5qE
Thanks for stopping by and supporting my channel!
This should be applicable for the years 1997, 1998, 1999, 2000, 2001, 2002, 2003, and 2004. There are some exceptions, but this gives you a general idea.
DISCLAIMER: The information provided in this video is for educational and entertainment purposes only and should not be construed as professional advice. The creators, producers, and distributors of this video do not assume any responsibility or liability for any errors or omissions in the content of this video or for any damages arising from the use or reliance on the information presented in this video. Viewers should consult their own professional advisors for advice and guidance. The use of any information provided in this video is solely at the viewer's own risk.

Пікірлер: 59

@ChandlersGarage790 4 ай бұрын

I cannot begin to tell you how much this helped, thank you! Your advice to check your work was spot on. I was about to pull the pins and I checked the chains and I was one tooth off on the crank sprocket right bank. You are an excellent teacher.

@user-sm6md5tr5z 3 ай бұрын

This is the best explanation I’ve came across on any KZfaq video. And I’m not just blowing smoke. You sir are a good man! Great video brother!

@newedgegt1947 Ай бұрын

This helps a bunch as I love this kind of content.

@mikediodato 12 күн бұрын

Man I love your videos and how well you explain how to do well, everything that you explain.!!! GREAT JOB.!! Keep it up man thank you so much.!.!.!

@keithbrown4865 6 ай бұрын

I would love to work beside you just to learn. I like how you take time to explain every detail. Thank you

@javosgarage 5 ай бұрын

You are so welcome! Thank you for the great compliment!

@AutomotivetechnicianBL 8 ай бұрын

Thank you mr for your video, has a lof of good information ❤

@wjye Жыл бұрын

This is fantastic. Thank you sir!!!

@javosgarage Жыл бұрын

Thanks Dan. I appreciate the compliment and I'm glad you like the video.

@vinghttois6537 4 ай бұрын

Took me a Day an a half but got it done really got to thank you so very much A blessed Day “

@maryc3808 2 ай бұрын

Very well done. Great info! What time can you be here?!

@StasMan1982 11 ай бұрын

Best breakdown of this process!! Another hard to find video showed that with keyway in <a href="#" class="seekto" data-time="720">12:00</a> position, pistons are down far enough to not cause any damage, but seeing your visual example with the cardboard puts it to rest! It seems you could rotate as desired but not tempting fate is always a sign of wisdom. I've researched for a few weeks now this timing process and your video was the first to show how to use the cam locks as well as rotating the cam sprockets before adjusting the crank sprocket and installing chains. I'm doing a head gasket replacement, and since I'm gonna have everything opened I finally pulled the trigger and ordered a Cloyes timing kit (because it included cam sprockets and seems to have a good name). Besides lining up my brother to help I think I'm finally ready to perform this open heart surgery on my 98 F250 5.4 2v. Gonna do all gaskets: intake, valve, throttle, head, and front cover. Thanks to folks like you I've learned that with persistence/patience/study I CAN do this myself. Truly thank you! Matt

@javosgarage 10 ай бұрын

Good luck with your project Matt, I hope it goes well for you. This motor was for my son's 1999 F250 5.4 2V so I would expect it to be pretty much identical for your truck.

@michaeldunn3042 5 ай бұрын

Great video. Is helping so much on my 2001 f150 5.4 2v. I have 318,000 miles so I guess I am overdue 😮. Does it matter which way you rotate the cam shafts when doing the timing? Thanks so much.

@emanuelorozco1439 8 ай бұрын

I just want to say that this video was very helpful. I did the head gaskets and timing with my dad on his truck before watching this video. After putting it all back together it started but it seems like it has a rough idle. No smoke comes out and there is no codes or check engine light. My dad thinks it is possible the the chain on one side might be off by a tooth. Engine runs with out any noise but would the chain being off cause this? Or would valves hit pistons?

@DimasMechanics 10 ай бұрын

I’m installing one of these engines in my truck, I’m at the timing chain now.

@javosgarage 9 ай бұрын

I hope your project went well and your truck is running great!

@MR20MR 6 ай бұрын

Sir, thanks for such a helpful information. Can you please tell me how can i clean the inside of cylinders without hurting them . Thanks a lot Javo!

@samanthacoutoure1653 Ай бұрын

On those tension arms, do you put oil on them before installing the timing cover? Sorry for the newbee question.

@gilsan769 3 ай бұрын

QUESTION How many rotations of crankshaft would I need rotate to realign the timing marks again , just to make sure my timng is correct?

@davidribarchek5853 2 ай бұрын

Hello and thank you for the very informative videos. I followed them to a tee. I do have a question. Since rebuilding the front and top of the 5.4 2v, the motor is running good and quieter. But....I now can hear a knocking noise in the lower end. I think it's a rod bearing but not 100% positive. I have a video of the sound and was wondering if I could get your input? Engine sounds can be tricky and before replacing anything I world like your opinions. I will send the video anywhere you would like. Thanks and hope to hear from you. Dave Rivarchek

@keithbrown4865 4 ай бұрын

Does the timing chain tensioners have a gasket or seal on them where they make contact to the block?

@AP-xq3jm 4 ай бұрын

I have 480k miles on my original chain. Everything on the truck is original. The chain is beginning to make noise on startup. It this point (milage) I'm not sure if I should replace the chain assembly or not.

@mikenorton8642 6 ай бұрын

What’s the part number too the tool that’s used to turn the cams

@mtsanchez27 21 күн бұрын

Is this the same for the 4.6l 2V?

@Vineyard_Edge Жыл бұрын

Yayy! I am always happy when I see you've posted a new video. Thanks for making more engine eye candy! 🍇💚🍇💚🍇💚🍇

@javosgarage Жыл бұрын

You're very welcome. I really appreciate you checking out my new video and then taking the time to leave me such a nice comment. Makes my day. Thank you.

@angelp9658 7 ай бұрын

Why is tension is tight bottom right and loose on the bottom lift side ?

@baqashahmath1566 7 ай бұрын

Awesome and very detailed video instruction where can I purchase the melling timing kit?

@waynebaker5720 7 ай бұрын

He also list all products in the description

@user-pz8kq3uj2g 3 ай бұрын

Здравствуйте, у меня тоже форд экспедишн. Подскажите пожалуйста какой фирмы комплект грм лучше?

@j.w.7688 10 ай бұрын

Your an awsome mech. Can you PLEASE do some vids on a 2001 Ford Excursion Limited, 6.8L V10? This is actually a popular vehicle but not a whole lot of vids exist for detailed repairs, etc., on it. Thanks.

@javosgarage 9 ай бұрын

Thank you for the great compliment! That would be fun but I don't have access to one of those at the moment. I have a friend that has one but his has the 7.3l. You never know though, there may be one somewhere in the future! Thanks for stopping by and taking a moment to leave me a comment.

@itsmeray01 9 ай бұрын

I have a 5.4 2v 2004 lightning, I did everything you showed and all went well , After replacing chains to correct marks and releasing the tensioners . I turned the crank bolt / sprocket just to verify that chaines were still in sync/ on the marks. Well i cant get them back in in position even after about 5 complete revolutions. will they evere get back to the My original settings?

@javosgarage 9 ай бұрын

They will. I don't remember exactly, but for some reason I remember when I was researching before this project that it takes something like 35 revolutions before all those timing marks align again. If you watch carefully, with each revolution the silver links on your timing chains will advance where they come in contact with the cam sprockets. They will get back there, but you would need to make quite a few revolutions to get there.

@justbryanoroarke Жыл бұрын

Just so I understand completely, you were able to rotate your cams clockwise without worrying about damaging your pistons because the pistons were all below deck by 20+ mm since the crank shaft keyway was at 12'oclock TDC correct? So you are able to rotate both cams around to the proper positions without any fear of damage to the pistons? Just wanting to make sure because every other video i've watched, even with the crank shaft keyway at 12 TDC, they make it sound like its really easy to damage the pistons because of the spring tension and it can turn over on you.

@javosgarage Жыл бұрын

Hi Bryan. You are understanding correctly. It sounds like you've watched the entire video but just in case let me say that I address this issue towards the beginning of the video starting at the 00:30 mark. I really tried to back up my opinion of using the 12 o'clock keyway position with hard, photographic proof. That way it's not subjective, it's just the true facts. Trust me, I get it; you just want to make sure you understand what I did. I have done two rebuilds: my son's 5.4 2V and the 5.4 3V from my wife's Expedition. In both cases I was able to leave the keyway at the 12 o'clock position and then rotate the cams to the 11 and 12 positions (then locking them with the hold down tool) to begin installing my timing components. Let me be clear though, I only rotated the cams forward to get to the alignment position, I didn't do more than a 80% rotation (as I did to the LH side in this video) at best. While I'm confident I could rotate the cams as many times as I wanted with the keyway at the 12 o'clock position, let's just say I didn't want to tempt fate so I didn't do multiple rotations. When you use the alignment tool and the keyway is set to the 11 o'clock position you can absolutely do damage if the tension gets away from you. You'll see the way I did it was to loosen the hold down clamps just barely enough to rotate the cam and then immediately lock it down when I got it to where I needed when I did finally rotate the keyway BACK to the 11 o'clock position from the 12 o'clock position. BTW... DO NOT rotate the crank forward to get to 11, only move it the little bit backwards (counter clockwise) from 12 to 11 as I discuss in the video. I hope that helps you out. Let me know if you have any other questions.

@justbryanoroarke 11 ай бұрын

@@javosgarage Thank yoU!

@mohdali-sc8wr 9 ай бұрын

👍

@javosgarage 9 ай бұрын

Thank you!

@UQRXD 9 ай бұрын

A Ford mechanic told me do not use the ratcheting tensioners, they put to much pressure on chains promoting faster ware. What do you think? I am working on 2003 4.6, 2 valve.

@Joystickoperator 7 ай бұрын

They do over time they stretch them prematurely. That is why Ford changed from cast to plastic blend tensioner

@UQRXD 7 ай бұрын

I'm sold the plastic up graded one are going in.@@Joystickoperator 😄

@angelfernandez866 9 ай бұрын

So you can assemble everything with the crank at 12 o'clock correct?

@javosgarage 9 ай бұрын

Yes you can. There are pluses and minuses with using either the 11 or 12 o'clock positions such as: 1. With the keyway at 12 o'clock the pistons are well below deck. However, to properly align all of your timing marks (cams, crank, chains) will mean your cams will be at a point where they have tension and will want to "jump" to a neutral position. 2. With the keyway at 11 o'clock pistons 1 & 6 are now at TDC so you don't want to move the cams because damage could occur. However, when the timing marks are aligned (cams, crank, chains) the cams will be in a "resting" position with no tension, so they wont want to "jump" forward. IMHO, the best practice is to align your cams into their general position (as I show in the video) at the 12 o'clock position and then use the crank alignment tool to adjust the crank to 11 o'clock, then you'll see the cams will almost fall into the correct position when you fine tune the placement of all the timing marks. This is better than having the tension you would have with the 12 o'clock position. I hope this makes sense to you.

@brandonbranco1 11 ай бұрын

Curious if the ratcheting tensioners retract when the engine is off (no oil pressure).

@javosgarage 9 ай бұрын

Hi Brandon. No, they do not. They are a ratchet type so as it extends there teeth that lock it into place so it cannot retract. However, you can use a pin to push in a catch so you can retract it if you need to.

@4Serviceplan Жыл бұрын

Is mellings timing chain the best one

@justbryanoroarke 11 ай бұрын

I ordered the Melling kit but after receiving it and reading more online, I returned it and ordered all the parts OEM from Ford. To me it wasn't worth saving $100 using after market parts. I came across multiple sites from people who had Melling fail, one of them within 600 miles of installing. That was enough to scare me out of using after market on this particular repair. Regardless of the kit, the information in this video is excellent and done very well.

@javosgarage 9 ай бұрын

This is a loaded question, depends on who you ask! LOL. I think I explained why I believed Melling to be the better choice for me but I can certainly appreciate the thought of sticking with OEM. I believe the ratcheting feature of the Melling was an advantage because it doesn't retract (or very little) when oil pressure is lost. I would completely avoid the no name cheap kits though, you don't want to have to redo this project in a year.

@javosgarage 9 ай бұрын

Thank you for the compliment Bryan! I hope your project went well and your truck is doing great.

@justbryanoroarke 9 ай бұрын

@@javosgarage 2003 F150 5.4 4x4 is up and running and runs sooo smooth. I blew a spark plug and thought that was the extent of the project. Once I got in to it, found my valve cover gaskets leaking. Took the covers off and found my timing chain loose. Pulled the timing cover and found one of the chain guides broken. Had to drop the oil pan to get the pick up tube out and found many of the broken chain guide pieces stuck in the pick up tube screen. Job turned into a complete timing job replacement as well as replaced oil pan gasket, oil filter gasket, valve cover gaskets, intake manifold, all spark plugs, coils, drilled and tapped all new spark plug holes using the Calvan kit and inserts, oil pump, water pump and I think that was it 😅. Two months of my life. I do not want to do it again! But after all that work, the truck runs strong and super quiet. Used many of your videos in my success. Thanks again for the time and effort making them.

@user-pz8kq3uj2g 3 ай бұрын

Добрый день, подскажите пожалуйста, какой фирмы комплект грм лучше? Спасибо

@dannypalmer7701 8 ай бұрын

Right side? But the camera is in reverse!

@StansE250 Жыл бұрын

‘03 5.4L 2V (E-series) Want to replace Intake while front is apart. OE is unobtanium. Suggestions ?

@javosgarage Жыл бұрын

Hi Stan. Unobtanium huh? Never hear that one before but it did make me laugh. I will have to steal that one from you. I'm sorry, I don't have any experience with these motors in the E series. I've looked at a few while at the salvage yard in the past and remember thinking it was really tight in there with little or no room to work. I wish I could give you some great advice here to help you out, I apologize.

@sabrom 10 ай бұрын

Is this the same procedure as with a 2007 4.6 2V??

@javosgarage 9 ай бұрын

I believe so, however there may be some updated items. This motor is a 1999 but I believe this should apply. I haven't done this procedure on a 2007 though.