Gear Indicator not lighting on dash, shifting problems, large orange wrench displayed in vehicles information center.
Пікірлер: 348
@MegaJared28 ай бұрын
Thank you for showing how that shifter needs to line up. Every other video skips that part
@markburgett82503 жыл бұрын
I was afraid to tackle this project, but your video is leagues above even the pros trying to show this. THANK YOU! You did not miss a detail. It took me three hours but only because I was laying in the gravel on the ground, but you did an amazing job and I got it put back together and it works great! Thank you so much! Mark in Wisconsin!!
@autohelp65043 жыл бұрын
Glad to hear this. That is a tough job on the ground.
@jstealth58612 жыл бұрын
I have a lift but still just put the truck on ramps lol
@WuffyWufferson Жыл бұрын
Yeahhh i gotta do this soon! Looking forward to this aweosme.. Job X3 don't seem too bad at all! I was worried when I got a 3k estimated bill from the auto shop. X3 less then 200 bucks if I do it myself with then 180 for reprogramming
@alb12345672 Жыл бұрын
@@WuffyWufferson No programming unless you replace the valve body(solenoids). And you can do the programming almost free with forscan for that.
@vicentebchacon10 ай бұрын
@@autohelp6504 Hi, I would like to know if the module is compatible with a Ford F 150 year 2011 with 5.0 V8 engine model FX4?
@soloriomartinn4 жыл бұрын
I just did mine today,dealer wanted over $2000 cause my suv has rebuilt title and void warranty, $150 part from amazon,$40 oil,2 hours of work Thank you so much buddy,great video
@autohelp65044 жыл бұрын
Glad to hear!
@adrianchavez47494 жыл бұрын
Can you post the amazon link to the part. Is your truck a 2011?
@soloriomartinn4 жыл бұрын
@@adrianchavez4749 Check this out at Amazon.com OEM Genuine Ford Connector Assembly for 2009-2014 Ford F-150 AL3Z7G276D www.amazon.com/dp/B00XLL5HQC/ref=cm_sw_r_other_apa_i_0iK-EbDMWGB43
@soloriomartinn4 жыл бұрын
@@adrianchavez4749 they just went up on price,cause ebay has them for $400
@user-yh5or1ze6rАй бұрын
Gracias salí de duda con tu vídeo soy de Venezuela y estoy nuevo en las cajas automáticas…me gusta la mecánica hidráulica.
@llopez65774 ай бұрын
Thank you so much!!! I've been looking for this for weeks.
@henrycomputer14034 жыл бұрын
Wonderful. Wonderful. You include common sense stuff we need to know and leave the bull out. Opposite of what the big guys do. Thanks for sharing your knowledge. God bless you. Keep it up. I know a lot about the old stuff made in the 50s to the 80s but am lost after that. I used to work in a machine shop and always shared my tricks. The customers loved it and always came back.
@autohelp65044 жыл бұрын
Your welcome. I love working on the old stuff. My 54 is so much more simple.
@jstealth58612 жыл бұрын
Awesome video! Thank you so much. I'm going to replace my lead frame this weekend. Should be much better with this video to use as a reference.
@gaspuppygarage37824 жыл бұрын
Spot on! using this video IJust did mine on a 13 Ecoboost. No surprises! Thank you!
@robjordan2043 ай бұрын
Did it fix the problem. Mine won't go higher than 5th gear and won't go lower than 3rd gear at a stop. Showing code P0720
@brianmcnutt88504 жыл бұрын
I have watched several videos concerning this tranny and yours does a good job on the shift linkage connection and showing how the electrical connector has the rotating piece that makes it lock in so thanks for that!
@autohelp65044 жыл бұрын
You're welcome. Those are the areas I struggled in so I tried to explain them well.
@davidmk0013 жыл бұрын
Have this problem with my 2016 5.0 F150. It wouldn't start, or it would idle rough and die. Took it to ford who claimed my trans was completely dead - gears were sheared as per the advisor. Quoted me $8k with parts, taxes and labor for a new one. Or, said I can trade it on a new one, but I wouldn't get much for mine due to a failed transmission and high mileage. Didn't belive the guy for a second. Took it to the private shop I goto usually and this was what the problem he said. Getting fixed rn. I'd like to try escalate the situation with ford who tried to screw me over and have me pay 8k!
@Guap3032 жыл бұрын
Literally in the process with doing this myself, took mine to Ford dealership they're giving me the run-around they can't replicate it there's no code stored and I don't have time for it to sit down for this maintenance guy to drive it around for however many days it takes for it to happen again just so they could diagnose it, of all places I found one at Advance Auto Parts for $200 just going to knock it out myself thank you for the video
@autohelp65042 жыл бұрын
Good luck. I will be here if you have any questions feel free to ask.
@Guap3032 жыл бұрын
@@autohelp6504 I appreciate the hell out of that, thank you sir!
@kevg6444 жыл бұрын
4:40 Genius, I never thought of putting grease to keep it from falling out.
@harounelmir26324 жыл бұрын
Works for Mustang 2012 too. Thank you for the vid helped a lot
@jstealth58612 жыл бұрын
That damn spring thing wouldn't stay in 😂 I remembered you said put a little grease on it and sure enough it stayed on.
@coryswinerton3296 Жыл бұрын
My Gen 2 6R80 with only 1600 miles on it after a rebuild, flared 300rpm from a 5-6 gear shift. Now, when trying to move forward, it seems like 90% of the line pressure isn't allowing full engagement in D, and the RPM just climbs with very little forward movement. Reverse engages perfectly fine. The car was driving perfect for the first 7 minutes, and then this came out of nowhere. I believe its a solenoid/valve body issue. No codes came up. I am swapping the valve body, bridge and tube seals today.
@autohelp6504 Жыл бұрын
Sounds like you are on the right track.
@ytpiano93 жыл бұрын
My truck had a no crank no start issue. I send it to my dealer and they change the lead frame. Now it starts. Took 4 weeks for the parts to get here.
@williamgonzalez80613 жыл бұрын
Just a FYI this works for 2016s as well that have that same part number thank you!
@JB-tw6hg2 жыл бұрын
excellent!! I'm going to try and tackle mine this weekend. Thanks for making it easy enough for a motorcycle (shade tree) mechanic to figure out!! LOL
@autohelp65042 жыл бұрын
Good luck! Message me if you run into a snag.
@JB-tw6hg2 жыл бұрын
@@autohelp6504 man, everything went smoothly…well, except for draining the fluid. Lessons learned, buy a new pan with a plug (eBay ~$60), and a small torque wrench (0-50 ft#). The instructions were exact. Total time was about 4 hours. Thanks for the help, your an awesome person for making this video.
@autohelp65042 жыл бұрын
@@JB-tw6hg That's great. Glad i could help.
@artyart313 жыл бұрын
Thank you sir, just saved me a couple grand. Wow followed step by step trans is back to normal.
@autohelp65043 жыл бұрын
That is awesome. I am glad to hear that.
@nathanpaul883 жыл бұрын
Hey art, were you pulling a p0705 code before this? I don’t wanna tear my tranny apart but that’s the code I’m pulling. Had an issue putting it in reverse the other day.
@artyart313 жыл бұрын
@@nathanpaul88 yes
@drifter00364 жыл бұрын
Great video. So much better than another one I watched previously. Clear, concise, and you did not skip anything ...except you did not mention the vehicle speed sensors. Do they come with the lead frame (since they are installed in it), or do you have to provide them? Also, you could include torque values for lead frame, valve body, and pan (not sure if this is correct, but elsewhere I have seen them as: 53 in-lbs, 71 in-lbs, and 97 in-lbs, respectively). Again, thanks!
@autohelp65044 жыл бұрын
Yes the oss (output speed sensor) does come preinstalled in the lead frame. I thought about including the torque specs after it was already posted. this was my first ever video and attempt at editing. next video should be better. Thank you for your compliments/advice.
@jstealth58612 жыл бұрын
Oof speed sensors? I didn't even look at those, they didn't come with my part and don't think they're a reason for my issue. Thanks for the torque specs tho, I just tightened by hand but not over tightened. Nice thing is I red this before my pan went back on so I'll check those torque specs
@jstealth58612 жыл бұрын
Damn dude you did great for a first video! great work
@matthewjohnson2495 Жыл бұрын
You my friend would be a great teacher
@goatee212 жыл бұрын
Was thinking I'd do this job, your video is awesome and showed me I probably better not! lol. Thanks!
@autohelp65042 жыл бұрын
Any time!
@soloriomartinn4 жыл бұрын
Best video,great explanations thanks
@juliustornabene71035 жыл бұрын
Thanks for this video. Super helpful. Nice rims.
@fastdonald Жыл бұрын
Excellent video! Very helpful. Thanks a lot!
@bobd37072 жыл бұрын
This was a great video. I think I can do this job. What is the torque on the bolts.
@jstealth58612 жыл бұрын
Liked and subscribed. Again thanks man great video. Saved a ton of time and money doing this myself plus I learned something and felt good knowing I took my time and did it right. Apparently previous owner put royal purple Max ATF in this trans, didn't have an issue with it but I'm doing the motorcraft Mercon LV. Reason for lead frame replacement was that every once in a while it would go into limp mode and throw a wrench light. I'm whipple charged so my throttle body is different than stock but I cleaned it anyway. When it still threw wrench light and went into limp mode I decided the lead frame was probably the culprit. We'll see. Regardless the leas frame in these trucks is a common issue. I replaced it with the new version which looked the same except for different part number and that foam seal at the solenoids. Do you recommend flushing out the rest of that royal purple? Any issue with a small amount of it mixing with the motorcraft?
@autohelp65042 жыл бұрын
you should be fine not flushing out the rest of the royal purple. it is almost impossible with these transmissions anyways. the thermal expansion valve makes it difficult to get everything out of the system.
@nonyabeezwax69323 ай бұрын
OMG THANK YOU THANK YOU THANK YOU THANK YOU THANK YOU THANK YOU THANK YOU THANK YOU THANK YOU
@can2trk4 жыл бұрын
You said there are 2 filter sizes? i have the FT-188, what is the part number of the other filter i think i might have put the wrong filter size in my trans and now i just have reverse, i put it in drive and it sounds like it clicks into gear but sits there i rev it and nothing, i checked it with my scanner and i can see its going through P,R,N, and into drive, im wondering if the filter might be bottoming out on the trans pan?
@phil-fr4lg4 жыл бұрын
Great repair video...step by step. Not a mechanic but handy and I can do that!!!! I assume repair is the same for the 2009 F150 lead frame with same trans...(?). Thanks🐾 Subscribed
@autohelp65044 жыл бұрын
It is the same.
@myfavorit3rifl32 жыл бұрын
helped me solve my issue! thanks!!!
@kirkragland75634 жыл бұрын
Excellent video! Explained it all in a way anyone can understand, left NOTHING out. Thank you! I just became a subscriber.
@autohelp65044 жыл бұрын
Thank you!
@joshparsons25344 жыл бұрын
Fantastic video thank you.
@christopherhuber25172 жыл бұрын
Nice thanks for the help
@muhammadzahidali6160 Жыл бұрын
Real nice video, Did not mention the DTC codes, are they P0706, P0702, P1702, P1921 Is it possible before performing that exercise to check the integrity of TR sensor with Multi-meter ?
@maniacfitness45782 жыл бұрын
My truck starts up good then when I put it in reverse it takes 5 seconds to get in gear and works fine then soon as I shift it in all the other gears the lights go out telling you if your in neutral or drive and all the low gears but as soon as you cut the truck off and start it back up if I go straight to drive I have no problems at all light are on and it hits every gear no problem took it to a transmission shop they say I got a p0705 code transmission range sensors a circuit park/reverse so I went got the same peace you put on your truck hopefully that's the problem!!
@maniacfitness45782 жыл бұрын
What you think?
@autohelp65042 жыл бұрын
@@maniacfitness4578 Mine was doing the same thing. I am confident this will fix you right up.
@willmedders405 Жыл бұрын
Excellent summary of replacement! My question is, before installing drain pan, would it be safe to VERY BRIEFLY turn ignition key on and off to make sure it sounds like it will crank. Heard some guys having to go back in after buttoning it all up due to no crank situation. Could be that connector is corroded or not aligned. Thanks.
@autohelp6504 Жыл бұрын
would not hut a thing.
@goose14984 жыл бұрын
There is a recall on this. I took it to the dealer....they said they had to reprogram it and if it does it again then they will fix it
@autohelp65044 жыл бұрын
yes there is. 10 year or 150k miles. most people are above this when they start to experience any issues.
@chadbrattain79854 жыл бұрын
I'm at 120000 miles on my 2011 and it's 9 years old and I called Ford and they refused to honor the recall on my car. My transmission is acting up like everyone else on the recalled car's and they confirmed that my mustang GT 6r80 was made at the flat rock facility and was in the year of the recall. They said they couldn't do anything because my Vin number is not on the list of the 201,000 cars recalled, but my car is from the same place at the same time as all the other ones but my car is not covered. They are trying to screw me out of the fix by putting me off until the end of the year when my car turns 10years old. I'm still a Ford fan but I hate the Rich bastard's that work there.
@cman77385 жыл бұрын
Great vid. I just had to replace the lead frame unit as well due to experiencing random shifting issues and trans getting stuck in 1st gear. Code P0720 (output shaft speed sensor). This vid helped, thanks.
@autohelp65045 жыл бұрын
Glad I could help.
@hidros14613 жыл бұрын
Thanks for the wisdom!
@Khaled-tx5xj4 жыл бұрын
I have a 2014 Raptor , it’s been like 3 months since I’ve changed the Transmission fluid , recently there is a Hard Downshift from 5-4 coming to a stop , ( sometimes it happens ) I have also 40 inch tires with 4.88 Front and rear gear ratios
@autohelp65044 жыл бұрын
Sounds like you need to clean all of the electrical connections inside the tranny pan real good with brake cleaner.
@Khaled-tx5xj4 жыл бұрын
Auto Help so you mean cleaning the inside of the tranny which is the solenoid for the 6R80 ? and should I change the filter of the tranny at the same time ?
@autohelp65044 жыл бұрын
@@Khaled-tx5xj yes, unplug all of the connectors and clean them real well. Also clean the magnets on the pan really good also. Definitely install a new filter and fluid as well. A big problem with these transmissions is metal clutch shavings build up around the plugs and cause small shorts in the electrical system.
@kevin_11_074 жыл бұрын
Great video man!
@autohelp65044 жыл бұрын
Thank you!!!
@NDLAP66 Жыл бұрын
Thank you for those instructions doing this project right now, question, will it have to be reprogrammed after you install a new one like the range rovers and BMWs?
@autohelp6504 Жыл бұрын
it does not require proramming.
@JR-ku3ws Жыл бұрын
Awesome job man.
@MrJohnburks4 ай бұрын
Pascagoula cannon ford lied to me as the recall calls for an upgrade of that control module.. they said reprograming it was the upgrade.. my ford is still messed up
@BR-rt7kj4 жыл бұрын
Great video. I have a 2016 f150, I got codes p0706 and p0707. When I try starting my truck, some days it starts, some days it doesn't only the lights would come on wouldn't turn over. When it would start, the lights for what gear it's in would flicker. Would that be the sensor? From what I read on the codes I got said my truck would go in limp mode or no start mode.
@autohelp65044 жыл бұрын
It really sounds like you have the same issue.make sure your bulk head plug is tight and free of corrosion before you do anything. I would also inspect the wires real good as well.
@autohelp65044 жыл бұрын
Check to see if your vehicle falls under the recall before you do anything.
@BR-rt7kj4 жыл бұрын
@@autohelp6504 is there transmission recalls ford f-150s? Thanks for your replies.
@autohelp65044 жыл бұрын
@@BR-rt7kj yes for the o.s.s replacement or reprogramming. This would definitely cause the issues you are referring to.
@BR-rt7kj4 жыл бұрын
@@autohelp6504 how long did it take you for this job? How did your truck perform after?
@severianojimenez8128 Жыл бұрын
Excelente. Tanks. Bro. I can do it. Let's go doing!!!
@pablopelayes43433 жыл бұрын
HOLA SOY DE ARGENTINA TENGO UN PROBLEMA CON UNA RANGER CON ESTA 6R80 CAMBIE LA CAJA PERO EN MI ESCANER ME DICE SENSOR DE PALANCA Y NO ENCUENTRO EL PROBLE LA LLEVE A CONCESIONARIO FORD Y NO ENCUENTRAN EL PROBLEMA ,SERA CAJA DE VALVULAS LA PARTE ELECTRONICA ESA QUE ES COLOR NEGRA MUY INTRITUVO EN VIDEOY POR SUPUESTO TRADUCIDO GRACIAS
@autohelp65043 жыл бұрын
English please.
@brandonsimmon20073 жыл бұрын
2012 here has transmission issues dealership said could cost 5k easily to repair so I bough a reman transmission it ran good for 3k miles then only had reverse 3rd and 5th code says shift solenoid stuck on and now the truck won’t move at all forward or reverse
@rethidlopex28232 жыл бұрын
excellent video, and thanks for sharing it, it's very helpful, I just have one question? Is the new module programmed, or does it have to be programmed. l have codig P0720
@autohelp65042 жыл бұрын
It is programmed and ready to go.
@rethidlopex28232 жыл бұрын
@@autohelp6504 thanks for la información. Blessings
@trevor19862 жыл бұрын
Hello, thanks for your video. I have a 2014 f150 eco boost with around 60k. Hard down shift into low gear at highway speeds. Intermittent slipping of transmission at low Rpm. I have also had the wrench light go on then off with speedometer not engaging. Symptoms will go away for a bit by turning ignition on and off, while also cycling through gears. Then vehicle will drive completely normal for around 40 or so miles. Does dealer say no recalls related to lead frame which I feel like it definitely is. Of course they recommend transmission replacement. Haven’t taken it to local transmission shop yet. Seeing what your course of action would be? Appreciate your time Would buy you some beers if you lived near me.
@autohelp65042 жыл бұрын
Sure sounds like a lead frame to me. When was the last time your pan was off? You may have a bunch of fine metal clutch clutch material built up around the plugs and solenoids causing it to short out. I would drop the pan and if that is the case give it a good cleaning with brake cleaner and compressed air. Fill it back up with fluid and a new filter and see what happens.
@trevor19862 жыл бұрын
@@autohelp6504 dropped it off at the trans shop yesterday, going to get the lead frame replaced. Hope it does the trick. Thanks for the reply!!
@autohelp65042 жыл бұрын
how did this work out for you?
@andrewbodey5025 Жыл бұрын
Very informative video. I have a 2011 F150 and it had the hard shift from 1st to 2nd and my gear indicator on the dash is out, would you recommend changing the valve body also?
@autohelp6504 Жыл бұрын
yes
@buckyjones2107 Жыл бұрын
@@autohelp6504 Does tcm needs any flashing on 2011 F150 with the install of the valve body and lead frame install? Thanks in advance. By the way, you are the man!
@autohelp6504 Жыл бұрын
@@buckyjones2107 It does not. Glad I could help.
@scubasteve14747 ай бұрын
I cannot get that white retainer clip to slide back up in the lock position, with or without the valve body seal in. Any tips?
@autohelp65047 ай бұрын
you have to make sure that bulk head sleeve is all the way in before that retainer clip will go in.
@joelusa13 жыл бұрын
I hope you did not forget to push the clip to hold the socket in place otherwise you are now leaking oil...
@autohelp65043 жыл бұрын
I did not forget.
@lcdsmarin4 жыл бұрын
Very good video!!
@ZteveW6 ай бұрын
What's the torque and tightening sequences for the lead frame to valve body, the valve body to tranny and transmission pan bolts?
@autohelp65046 ай бұрын
to be honest I just tightened them with no regards to torque specs. LOL
@rsmetalguitar3 жыл бұрын
I'm looking into F150 and I'm seeing this issue is fairly common yet the part is discontinued, not sure why a part would be so hard to find when this is a known problem. Also seeing it mainly happen to trucks with ecoboost. Do you know if trucks with a 5.0 have the same issue?
@autohelp65043 жыл бұрын
It happens with all engine types. The part is not discontinued.
@WuffyWufferson Жыл бұрын
I found a lot of ebay for 200 bucks
@rakanahmed87174 жыл бұрын
I have mustang 2012 6r80 the same trans you have ,I got p0705 which is” transmission range sensor A curcit (PRNDL) input , i changed the same that you changed too, but problem still appeare, I can’t use gears “1-2-3” and on D its running normal like any cars, but when I try to go with 3/2/1 or any , wrench light pop up!
@autohelp65044 жыл бұрын
Check the wires going to the transmission and make sure they did not get smashed,worn,or burnt.
@andrewshah10 Жыл бұрын
Hey man thanks for this awesome video. I’m thinking I need to replace my valve body on my 16 f150 5.0 ; 97k miles ,6r80. I’m having intermittent shifting issues particular at faster speeds on highway.sometime when I press on gas to go faster tranny gets stuck in lower gear and the only way to get it back to normal is to let off the gas and cycle back through gears. Anyway was hoping for some insight if you think that could be the problem and also if I change this part will I have to do any programming or reflashing of anytype? Im replacing the entire valve body and lead frame. Thanks!!!!!
@autohelp6504 Жыл бұрын
It sounds like you are a good candidate for a new lead frame. metal clutch material builds up on the electrical components in these causing shorts. you will not need to do any reprogramming. make sure you have lots of brake cleaner o hand to clean up.
@andrewshah10 Жыл бұрын
@@autohelp6504 thank you so much for the reply man!
@kmstanley793 жыл бұрын
Good video, but no torque specs for reassembly? And, can you list part number for the lead frame?
@autohelp65043 жыл бұрын
71 in lbs on the t-30 bolts that hold the valve body in. look in the beginning of the video@ 0.33 I show the box that the part came in, The part number is on the box.
@josueflores51465 жыл бұрын
I got a P0720 code with the wrench on my instrument panel, my truck was stuck in 1st gear, I deleted the code and my truck started to run normal again. Do you think the lead frame will still need to be replaced? My truck is an 11 f150, thanks
@autohelp65045 жыл бұрын
My truck did the same thing and then finally got stuck for good. I would guess that its just a matter of time before yours does it again.
@josueflores51465 жыл бұрын
Auto Help I appreciate the reply, I called Ford and there’s an extended field service action, Ford extended the coverage on the lead frame for 10 years or 150,000 miles. They told me that my truck qualifies, however since I deleted the code they can’t replace the lead frame until it happens again and I have to get it towed with the code or wrench on the panel, not sure if they’re reimbursing owners for repairs already done but it’s worth looking jnto it, thanks again I’ll keep you posted if mine ever gets done, well when it does hopefully I’m only at 98k miles currently. www.cnbc.com/2019/02/13/ford-issues-3-recalls-covering-nearly-1point5-million-vehicles.html
@moneyboy98453 жыл бұрын
Do you have to have the tcm reprogrammed after the installation?
@autohelp65043 жыл бұрын
Amber Strickland no
@bobd37072 жыл бұрын
The answer was in the comments thanks
@autohelp65042 жыл бұрын
Glad i could help.
@markburgett82503 жыл бұрын
Hi. I spoke too soon...I went out today and the truck wont turn over, crank or click..nothing. I am wondering if the connector pin at the back of the tranny would have anything to do with that? It locked in nice and tight with the new coupler, battery is fully charged, but won't start? Just wondering if you might know anything there? Thanks a bunch. Mark
@rhyskyeremeh82444 жыл бұрын
WHERE DID HE BUY THAT UNIT. MINE IS SPOILT TOO GETTING ERROR CODE P0500 TRANSMISSION DRIVE SPEED SENSOR. PLEASE SEND ME WEBSITE YOU BOUGHT THAT UNIT FROM. THANKS.
@autohelp65044 жыл бұрын
I bought it directly from the Ford dealership.
@rhyskyeremeh82444 жыл бұрын
@@autohelp6504 Alright thanks.
@Erick2507912 жыл бұрын
Hola Desde México Tengo un problema en cambio errático en baja velocidad de 1 a 2 solamente embraga se suelta y después patea Al acelerar un poco más rápido el problema desaparece Será que está sucio la parte interior del Leadframe No soy Mecanico pero me gusta meter la mano Gracias por su respuesta Estaré agradecido
@autohelp65042 жыл бұрын
Very likely.
@TERRORoftheLORD Жыл бұрын
Why did you replace the range sensor exactly, and did it solve your problem?
@autohelp6504 Жыл бұрын
erratic shifting, randomly would not move, and sometimes no reverse.
@jdmmarcelo103 жыл бұрын
Nice video sir did you have e reflash anything ? Or just delete the codes the came up
@autohelp65043 жыл бұрын
No reflash required.
@jdmmarcelo103 жыл бұрын
@@autohelp6504 thanks awesome doing this to a car on Wednesday
@markpezenosky5592 Жыл бұрын
Why did they make this thing that a plastic I have no idea I’m sure some engineer knows
@timothymaxey95994 жыл бұрын
Question about the foam on the lead frame, when you took it out there is no foam on it. Did the directions say why when putting the new one in there was foam going on the connectors? is that part of the fix of the lead frame not grounding?
@autohelp65044 жыл бұрын
yes, the foam is designed to keep metal shavings from building up around the electrical connectors. It is part of the upgrade.
@timothymaxey95994 жыл бұрын
@@autohelp6504 thanks. Planning on doing mine shorty.
@principeazul16942 жыл бұрын
Great video. I need to replace the same part. Sensor range or something. But my question is, If i change that part i need to reprogram the ECU with the new part..?? Some people say i got do it. But some other guys says no. So im confused. Somebody can let me know please.
@autohelp65042 жыл бұрын
I did not have to reprogram mine when i installed it.
@lautaropardo1640 Жыл бұрын
Hola como se llama la pieza esa que va atornillada al cuerpo de valvulas?
@emindiri2985 Жыл бұрын
Çok güzel olmuş eline sağlık
@CarlosGonzalez-hh5ex Жыл бұрын
Hay que programar la pieza con el vehículo
@mr.djcooncoon81963 жыл бұрын
How much would you charge for this job with parts?
@autohelp65043 жыл бұрын
$600-$800
@ChapoTheCorgi6 ай бұрын
Where’d you buy the sensor from??? And how much was it?
@autohelp65046 ай бұрын
Ford. It was about $300
@usamawarraich7571 Жыл бұрын
Hey mate i have got ford ranger 3.2 auto trans 6R80 , everytime i downshift from gear 5to 4 gives me a jerk other gears shift and downshift nicely what do you reckon the issue might be? Valve body or the solenoids? Car has done 304k kms
@autohelp6504 Жыл бұрын
look for metal clutch wear material built up around the connections of the shift solenoid plugs. If there is none present it is more than likely the shift solenoid.
@chiefofsinners9782 жыл бұрын
Thank you.
@autohelp65042 жыл бұрын
You're welcome!
@chiefofsinners9782 жыл бұрын
@@autohelp6504 seriously, I was screwed, until your video. Your awesome
@jackhenry62683 жыл бұрын
Is the new lead frame designed better since these recalls or is it the same part that can make it fail again?
@autohelp65043 жыл бұрын
It is pretty much the same except a foam gasket around the electrical connection has been added to prevent small metal fragments from collecting around the terminals causing a short. Replace the fluid more frequently and you should never have another issue.
@WuffyWufferson Жыл бұрын
Sk mine is leaking thru the connector. Do you think that bushing is what failed and can be easily replaced?
@autohelp6504 Жыл бұрын
Yes that is called the bulk head connector i believe. you can just change the o ring on it or the whole piece that's up to you.
@brianhester27235 жыл бұрын
Did you have to reprogram the truck as I'm reading it needs reprogramed?
@autohelp65045 жыл бұрын
No I did not. however there is a recall for reprogramming that will prevent your truck from downshifting into first gear if your oss sensor fails.
@mandorojo48134 жыл бұрын
My 09 f150 fx4 80k drives and feels fine with a blue wrench light on the dash code p1707 but got diagnosed with a bad Mechatronic module. Any information on this particular case? How much was yours?
@autohelp65044 жыл бұрын
Unfortunately i do not have much experience with this particular issue. I believe it has something to do with the transfer case.
@brandonbowen7644 жыл бұрын
Mine will not go in reverse I have n and D when I put in reverse it takes a minute then goes in to reverse and wrench light comes on and give p0705 code would replacing this fix it
@autohelp65044 жыл бұрын
It should be under recall. Call your local dealer.
@brandonbowen7644 жыл бұрын
@@autohelp6504 mines 2011 with 246xxx miles
@autohelp65044 жыл бұрын
@@brandonbowen764 oh,ok I would say that that a new le as d frame should fix your problem but I cant s as y for sure. It sound like yours is doing the s ac me thing as mine. Let me know what you figure out.
@brandonbowen7644 жыл бұрын
Alright bud I will
@brandonbowen7644 жыл бұрын
There is a 10 year 150,000 warranty but I was 100,000 over I got the lead frame yesterday and it did fix it I watched your video while doing it thanks for the video I used a harbor freight siphon pump to fill transmission back up worked great
@Musclemyke3 жыл бұрын
They just did a recall fix for this very reason for my 13’ it shift like a lambo now
@dmithsmith58803 жыл бұрын
I have a 13 stx with the natural aspirated 3.7.. The tranny shifts up nice and down nice except when shifting down from 5 to 4 it kind of bangs.. not terrible but enough to be annoying.. Was yours doing that ?
@andygambill47204 жыл бұрын
Followed your steps and got the lead frame replaced but now my truck won’t start and says it needs to be shifted to park when it’s already shifted into park. Any clue what went wrong?
@autohelp65044 жыл бұрын
just guessing, but it sounds like something is not plugged in all the way.
@harounjr42482 жыл бұрын
Nice video
@MrEfthimiou Жыл бұрын
Hi guys, I have a Ranger 3.2 with 6R80. Can someone help where to buy it? Ebay unbranded are a good option? Has someone use it?
@dankeronen4 жыл бұрын
Will this sensor cause a no crank/no start issue? I'm not getting any DTC codes? I'm stumped as it seems intermittent.
@autohelp65044 жыл бұрын
Daniel Keronen it could if it is not registering that the truck is in park or neutral. Is the park light on th indicator illuminated?
@cryptoplay6981 Жыл бұрын
FAILURE !! He did not lock in the bulkhead sleeve before locking in the wire harness. This will leak and the harness will unplug.
@autohelp650411 ай бұрын
77,325 miles later it is still not leaking or unplugged. you should probably stick to crypto. 😂😂
@cryptoplay698111 ай бұрын
Just going by what I saw on the video. I do like crypto and I'm an Industrial Diesel Mechanic. But totally not disrespectful Unlike your reply @@autohelp6504
@luisambriz5131 Жыл бұрын
What was wrong that you have to replace it.
@autohelp6504 Жыл бұрын
truck would not move sometimes.
@johndamron8343 жыл бұрын
Hey bro I’m working on a 16 did they not use the spring on the thermal valve or did it roll away from me?
@autohelp65043 жыл бұрын
As far as I know they did not get rid of the spring.
@luigilsperu4 жыл бұрын
For those who don’t know there is an EXTENDED WARRANTY FROM FORD,,,,FREE REPLACEMENT. 10 years 150k miles.
@autohelp65044 жыл бұрын
Thanks, unfortunately I was At 187k.
@biggameslayer37824 жыл бұрын
Link?
@luigilsperu4 жыл бұрын
Just go to dealer and tell them you know about The extended warranty , that’s it. I just did 2 mustangs last month.
@biggameslayer37824 жыл бұрын
LuigiPeru Will it work for a 2010 F150 with 82,000 miles?
@luigilsperu4 жыл бұрын
HighRiskEmployee I’m pretty sure yea
@wogboy47084 жыл бұрын
Mate the white clip thing you pull down.. I can't get it back up.. Its stuck down, it's holding me up, you missed it in the video, how do you get it to slide back up???
@autohelp65044 жыл бұрын
Typically if it will not go back in that means that the big electrical plug is not inserted completely. there is a notch in that plug and it will not go in all the way unless it is lined up.
@wogboy47084 жыл бұрын
@@autohelp6504 yep got it mate thanks for the reply, it was actually in too far pulled it outwards at the same time as pushing up and it popped up. Just so you know you put the crapy valve back in, they make an upgraded valve replacement that allows constant flow.
@nathanmcneal12244 жыл бұрын
Is the lead frame the same on the mustang ? part number wise I can only find replacements for f150s but I have a 2012 mustang.
@autohelp65044 жыл бұрын
It is the same.
@edross6412 жыл бұрын
@@autohelp6504 How about 2017 Mustang
@aiaautorepairllc45294 жыл бұрын
That work in my ford expedition limited 2014 or not help me please where is located solenoide A
@hotdog24825 жыл бұрын
Why do you have to change it and what it was the problem can you tell me
@autohelp65045 жыл бұрын
I had to change it because my truck stopped moving. The only gear i had was reverse. The gear indicator on the speedo was not lighting up either (except for reverse). I also had a picture of a big orange wrench displayed on my dash. I then ran the codes and got a p0705 (transmission range sensor) let me know if this helps.
@By_Any_Means_Necessary4 жыл бұрын
@@autohelp6504 hey I'm getting the code for my speed sensor is that the same thing as the transmission range sensor that you got my symptoms are intermittent but i got the wrench and the check engine light and my speedometer wasn't working but mine would go into like a limp mode and stay in third gear when in drive i had to cut the car off and sat for a couple of minutes and now the speedometer started working again so it's shifting again but still have the check engine light
@autohelp65044 жыл бұрын
@@By_Any_Means_Necessary yes, the speed sensor is in the lead frame.
@taylorbusche64159 ай бұрын
I did this and now my truck won’t go into reverse. Please help
@autohelp65049 ай бұрын
will it go into drive? would it go in reverse before you did the lead frame?
@andresmanzanares8480Ай бұрын
Is there any reprogramming necessary?
@autohelp6504Ай бұрын
No
@andresmanzanares8480Ай бұрын
@@autohelp6504 thank you
@nhoj1106 Жыл бұрын
is it the same as TRS of 2017 ford transit van?
@autohelp6504 Жыл бұрын
not sure
@phil-fr4lg4 жыл бұрын
Hey...followed instructions and no engagement when placed in any gear. Could I have fried the board cuz I did not remove the battery cable or I did not get the shift linkage in slot on trans side. Any wisdom on this ? Thanks😊
@autohelp65044 жыл бұрын
I would say you do not have the linkage hooked up properly.
@phil-fr4lg4 жыл бұрын
@@autohelp6504 well I have to drain and look at that again...99% sure detent was in the slot. Can I drain and turn ignition switch to accessory to move shifter linkage and validate full range of position - without fluid or starting. But if nub is seated correctly..then what? Could I have a bad new lead frame or did I fry it by not removing battery cable...thanks for your insight again😊.
@autohelp65044 жыл бұрын
@@phil-fr4lg sorry i did not see your last question until now. Have you figured out what was wrong?
@phil-fr4lg4 жыл бұрын
Linkage was correct for valvebody & leadframe...went with defective leadframe. Tech said it might be that the PCU needed to be updated to latest software because mine has never been upgrated from 2009. We'll see what happens with new unit...thanks. Will update when completed for everyone😊