Good work, how long does it take to remove fender a take back the new one? One hour?
@chrisr24242 жыл бұрын
hi, Looking to do this very soon. I did notice that the wings you put on didn't have any of the holes for the skirt end cap. how did u securethe end cap back on? Great video tho, I'm definitely going to use it for when I remove mine.
@dlxrekond2 жыл бұрын
Thank you very much and sorry for the late answer. It’s correct unfortunately. I think I did use som tiger seal. Good luck mate!👍
@wikiwong3 жыл бұрын
Will be doing both of mine in a few weeks. Any tips or something you’d do differently? Seen that you took the bumper off, is there any tips in doing that as well? I’m not very good with cars 😂
@dlxrekond2 жыл бұрын
Hey mate! Make sure to not stress. Buy 2k products and don’t forget primer in the inside of the wing and some clear coat to prevent rust. I would like to hear about your results!😃
@simonlowe40133 жыл бұрын
Nice work pal, what did you use to stick the small section of the kit back on?
@dlxrekond3 жыл бұрын
Thank you mate! Do you mean the front bit of the side-skirt?
@simonlowe40133 жыл бұрын
Dlx Rekond Yes pal
@dlxrekond3 жыл бұрын
@@simonlowe4013 Just slide it in and put the screw underneath it back on. Add a bit tiger seal if you want. It depends on how good fitting quality your new front wing/fender have. Good luck mate 😃
@simonlowe40133 жыл бұрын
Dlx Rekond Cheers mate 👊🏻👊🏻
@debw21073 жыл бұрын
Hi im in need of a new wing for my electric orange st 06 plate as mines got huge hole where it clips the trim so it keeps hanging off 🤦🏻♀️ where did you buy these from ? as genuine wings are £650 plus 😬
@dlxrekond2 жыл бұрын
Hey! I bought mine from AUTODOC. Have you checked there? Be sure to choose the right oem code on the wing before buying anything. If you need help with anything just ask! Cheers 😃
@Ajwright08113 жыл бұрын
Where did you purchase the new wing from? Thanks
@dlxrekond3 жыл бұрын
Hey mate! From AUTODOC! Cheers 😃
@fahmeez863 жыл бұрын
Hi bro, what colour code do you use?
@dlxrekond3 жыл бұрын
Hey mate! Ford Performance blue. Cheers 😃
@btd19933 жыл бұрын
nice video! i have the same problem on my focus wagon from 2006, already got the new panels. I have a question, is it necessery to take off the front bumper? And maybe a tip, I always learned that the new coat needs to harden more thorough and breath several weeks after being sprayed, applying wax to the panel is kinda delaying this.
@dlxrekond3 жыл бұрын
Thanks mate! If you’re only removing one of the fenders you can loosen up the bumper to access a screw underneath the fender. Check from 6.43min inside the video 😃 I recommend 2-3 months before applying any wax etc on the area. Angelwax redemption is a fine polish mate not a wax. Cheers 😀
@btd19933 жыл бұрын
@@dlxrekond aah i thought it was wax! haha. I bought a primer that says its hard after 2 hours, would u recommend to wait a day and than sand like u did in the video? Or could i just spray it after 2 hours of hardening without sanding?
@dlxrekond3 жыл бұрын
@@btd1993 I recommend you to read the recommendations on the product. It’s a lot of different primers out there. Make sure you have the right temperature too. But I recommend you to use a “2k” primer where you mix the primer and the hardener together. I’m not sure if they sell “2k” in spraycans tbh. I just know that you can find clearcoat in 2k with an activator in bottom of the spraycan. 😃
@jununee3 жыл бұрын
Damn that music was annoying but thanks for vid! :D
@dlxrekond3 жыл бұрын
Haha 😂 thanks a lot mate!😄
@RGD-Repairs3 жыл бұрын
Looks clean AF dude :) Shame it’s an ST tho 😉 Gallons Per Mile.... You know what I mean 😁🤣
@dlxrekond3 жыл бұрын
Haha thanks a lot mate 😎💸😆
@user-ii6ju6lm7w3 жыл бұрын
Some comentry would have been good!!
@dlxrekond2 жыл бұрын
Thanks for commenting. I’ll try next time. Cheers 😃