Ford Quick Tips #82: Ford CIII Power Steering Pump Pressed Pulley Removal and Installation Procedure

Рет қаралды 257,784

6 жыл бұрын

Welcome back to the shop! Today we go over the proper procedure to remove and install the pressed on power steering pump pulley found on Ford CIII pumps.
These are the Parts and Tools I Recommend:
Remover and Installer Kit- (Best Value Quality Kit)
amzn.to/2D0aerU
My preferred Reman Power Steering pumps I use-
#1 Choice-
amzn.to/2BTjvTH
#2 Choice-
amzn.to/2BQ1G7I
My Company BSG Automotive offers Auto Repair services in the greater Chicagoland area.
Website:
www.bsgautomotive.com
Facebook:
/ bsgautomotive
Catch up with us on-
Facebook: / fordtechmakuloco
Twitter: / fordtechmak
Instagram: / fordtechmakuloco
My company KZfaq Channel- BSG Automotive providing repair advice on makes and models other than Ford: / bsgautomotive1
Disclaimer:
The information, demonstration and any content contained in this video is for informational purposes only. The user and BSG Automotive (hereinafter “FordTechMakuloco”) makes no warranty, express or implied, regarding the effectiveness or safety of the contents of this video. In no way should the contents of the video, including the tools used, be repeated or tried by anyone. Viewers should only seek the help of a trained professional located at a licensed auto repair shop for any fix, modification, alteration, or any change to their vehicle. FordTechMakuloco shall not be liable for any injury, damage, or loss to any person or property that may result from use of the tools, equipment, or any content contained in this video. In addition, there is no way to guarantee that the video is not altered or modified or is not in the final form submitted by FordTechMakuloco and therefore, FordTechMakuloco does not warrant that the video is unaltered or not modified. The links on this video to products are for informational purposes only and in no way are an endorsement of the safety or effectiveness of the particular product. Viewers understand that anything contained in this video or linked to or from this video is the sole responsibility of the viewer and in no way provides an express or implied warranty as to the safety or effectiveness of any linked tool, product, or video. Therefore, viewer agrees to release, waive, and discharge FordTechMakuloco or anyone affiliated with FordTechMakuloco, from any and all liability, claims, demands, actions, and causes of action whatsoever arising out of or related to any loss, damage, or injury, including death, that may be sustained by the viewer, or to any property belonging to viewer, regardless of whether the loss is linked to the use of the contents of this video, or otherwise and regardless of whether such liability arises in tort, contract, strict liability, or otherwise, to the fullest extent allowed by law.

Пікірлер: 155

@FordTechMakuloco 6 жыл бұрын

These are the Parts and Tools I Recommend: Remover and Installer Kit- (Best Value Quality Kit) amzn.to/2D0aerU My preferred Reman Power Steering pumps I use- #1 Choice- amzn.to/2BTjvTH #2 Choice- amzn.to/2BQ1G7I

@MrBrandon2244 6 жыл бұрын

FordTechMakuloco my 06 mustang gt just started slipping 3rd to 4th gear. No engine light and no problems with reverse. Took ot to aamco and they said i need a rebuild. Any suggestions??

@MarkWilliams-vp7xw 6 жыл бұрын

Do you have a video on replacing the rack and pinion?

@robhoug3724 5 жыл бұрын

FordTechMakuloco just in case ER um someone installed the pulley backwards how would one remove it? Yes I know probably going to have to install a new pulley after but how does my friend remove such an embarrassing mess up.

@joshharrison1715 4 жыл бұрын

Hey Ford tech I have a question for you

@joshharrison1715 4 жыл бұрын

I have a 5.4 Triton 2004 Ford F150 I replace the power steering pump and now I'm leaking motor oil somewhere around the power steering pump I did not have all the bolts to put the new power steering pump back on so I did not know if all could be coming out of one of the boat holes or where could it be coming from thank you

@wylareedy9635 27 күн бұрын

He explained the entire procedure very well.

@willturner4289 3 жыл бұрын

Just broke my install tool and I’m broke so stressed right now, really appreciate you going out your way to inform us

@carlm.m.5470 Жыл бұрын

I broke two of those loaner tools from the parts store. It busted inside the pump with the separately purchased pulley partially installed. All three items rendered useless. Yesterday, I bought my own cheap version of the tool, but after seeing this, I bought the OTC tool he recommended. I'll wait on the OTC tool to arrive and just eat the cost on the cheap tool, because I don't want to buy another pump and pulley. Those cheap tool sets seem to be almost a one-time use. If you can find one with the pulley installed, they are $243.00. This is such an easy job, but it's filled with needless hurdles.

@jonathanjohnson647 9 ай бұрын

Piece of wood and a hammer

@mike289homebuilt5 8 ай бұрын

Hey guys, I had to do this same job on a chevy blazer and It took like 5 attempts to take pully off or on. I ended using a propane torch to heat whole pully and I could get 4 or 4 wrench turns then reheat repeat. Make sure shaft and pully have no Burr or scrapes on it. Some cars we work on are too much bigger pain.

@LeeFred78 2 ай бұрын

Thanks for this video. I had to replace the PS pump on my 2008 F150. I ordered one with a pulley but of course I got one without. Got the tools to do this job and it all worked out.

@garrettschuchholz4203 Жыл бұрын

I think your explanation of the endplay just saved from pulling a decent pump. Thank you.

@ozzstars_cars 6 жыл бұрын

Interesting how much end play is acceptable. Nice demo with the tool Brian.

@TravisMontesano 3 жыл бұрын

Good thing I watched your video. I had no idea I needed another tool to put the pulley back on. Thanks again for the save!

@patw52pb1 6 жыл бұрын

Thank you and all those involved in the content, efforts and production of this channel. Merry Christmas, Happy Holidays and Happy New Year to all. May the new year bring you, your families and friends much health, wealth, happiness, safety, security, appreciation, respect and peace.

@heavymetalapocalypse8354 6 жыл бұрын

This couldn't have come at a better time. Ordered my new pump and hoses last night and picking them up today. This is my first time so here goes nothing! Thank you! Merry Christmas everyone!

@ronaldcach2779 6 жыл бұрын

Where did you order your new pump from? THANKS

@heavymetalapocalypse8354 6 жыл бұрын

Ronald Cach i got it from auto zone, it was only like $50, but with the core charge it was $63 and some change. I got it the next day as well.

@heavymetalapocalypse8354 6 жыл бұрын

Ronald Cach I also got the hoses and rebuild kit from them.

@ronaldcach2779 6 жыл бұрын

Thanks

@ronaldcach2779 6 жыл бұрын

Thanks

@57Fastjeff Жыл бұрын

Great info! Thanks. Bought a similar kit and was stunned not to see the Puller" I had expected!

@maherzaidan7190 6 жыл бұрын

As usual nice video , I wanna wish you a Merry Christmas 🎁🎄 & happy new year 🎊

@fieldsofomagh 6 жыл бұрын

Happy Christmas and a great New Year.

@ugh3012 6 жыл бұрын

Just ordered the tool. Thanks for creating this video.

@roberts5858 6 жыл бұрын

Didn't notice the end play until I was putting the belt back on. Thought for sure I was in trouble. Thanks for saying that it's normal

@michaeltyniec7010 4 жыл бұрын

Thanks so much for posting this very informative video!

@baxrok2. 6 жыл бұрын

Excellent demonstration! Thanks and happy holidays!

@tacc8227 Жыл бұрын

I just replaced my steering pump recently (03/23) and the video information is still quite valid and good. However a few things not mentioned is the plastic/teflon o-ring. It is not pliable, meaning if you stretch it too far it will not regain its original shape. Also meaning when tightening the high pressure side of the hose into the pump with the plastic/teflon ring may not get sealed correctly. I , luckily, was able to get a good seal even though the ring was loosely fitted. No leaks after 3 days.. But will keep an eye on it. The other thing that should be mentioned is the tool for removing and pressing the pully should be high quality. While the "Harbor Freight" - made in china, did the job. I had improvise to get the job done. I ended up having to use a hose clamp rather than the provided sleeve due to the fact there was so much slop and play that it didnt allow the collars to stay in place when trying to take it off, which in turn made the tool fail in the end. And as he suggested @8:45 the installer bolt breaks quite easily, especially when taking the pully off. I broke the part 2 times, first time when taking the pully off and second time when I pressed the pully too far and had to pull the pully away form the pump body without the pully rubbing against the pump. In essence, because of the low quality tool I used it took a 3 hour job and made into a 2 day job just because I wanted to save money on a tool I knew I probably wouldnt use again.

@jdmeaux 6 жыл бұрын

Merry Christmas to you and your family.

@MrTrxter 6 жыл бұрын

Once again another sweet video. Thanks !

@RoyalKingA73 6 жыл бұрын

Excellent video

@luisandresfaundezquiroz4754 3 жыл бұрын

Amazing video ! Thanks for this !

@denniswilkinson1118 6 жыл бұрын

Thanks Brian good info

@burtferguson5276 Жыл бұрын

Thank you for posting this video

@ZHPBrent 3 жыл бұрын

Great info. I just did this on my 6.4 powerstroke

@michaelogibowski8370 8 сағат бұрын

I would like to see a video on replacing the pressure hose. It's a bear to replace if the nut is on the hose already.

@vinceb9215 5 жыл бұрын

Last year I did my phasers and all and changed idlers, tensioner, have new alternator, new water pump, etc. Now there is an intermittent squeal like a tensioner from the power steering pump side of the bay. Pulled the belt and everything is smooth and thought the play meant this was the issue but now I'm not sure. Thoughts? Thanks for all your videos too the phaser one was super helpful!

@mikebadilla6970 2 жыл бұрын

Thank you so much.I need all the help i can get.

@AntonioClaudioMichael 6 жыл бұрын

Thanks so much. Brian

@cody6 6 жыл бұрын

Good video Brian, I always did the pulley removal on the car. I never could get at the bolts and hoses with the pulley on

@theundergroundlairofthesqu9261 3 жыл бұрын

See FTM's video, Ford Quick Tips 75, for his advice on removing these pumps!

@jehzeel255 Жыл бұрын

Great video thanks

@thomashurley1163 6 жыл бұрын

I’m following your excellent four-part timing chain videos and the last thing I need to do is to remove the power steering unit before I can pull off the timing cover. (I already found an incredible amount of broken plastic chunks from the timing chain guides in my oil pan so I know I am on the right track. My pickup tube was so clogged with plastic debris that if it were one of my coronary arteries I’d be on a table at the ER with paddles on my chest and someone shouting “Clear”). I was able to get the lower bolt loose but I’m having a heck of a time getting the top front bolt to break free and I’m afraid that I will round off the bolt if I try any harder. Is it possible to just remove the pulley and leave the rest of the power steering unit in place to get access to remove the timing cover? It looks like there is only a single 13mm bolt behind the pulley. Thank you for your excellent videos.

@ericm6519 3 жыл бұрын

Thanks for another great vid! Question: When removing the pump for replacement, is it necessary to also remove the pressure hose with it? I would like to leave the hose alone, if possible. Thanks!

@101fish9 3 жыл бұрын

Excelente video . Thank you .

@jagoss45 6 жыл бұрын

2 weeks too late. But luckily I got a reman with the pulley installed and got the old one off without pulling the pulley.

@tizocpeinado 4 жыл бұрын

Love your videos, they help me out a lot!! I have a question if you get the chance to help me out? I have a 5.4 in an 08 F150, I have swapped out the High-pressure line on the power steering system twice but keep getting the same leak at the pump even with a new pump installed. Do I need to buy the line at the dealer? The ones I have used are from and auto parts store.

@GotWire 6 жыл бұрын

Greate video man am going to have to replace my power steering pump here soon on my 2007 ford f150 4.6L 2 valve and was wounding if you could do a video on how to remove and replace it :)

@39knights 4 жыл бұрын

I know that when putting on pressed wheel bearings there is a suggestion of putting them in the freezer to shrink them and make installation easier. Have you ever tried placing the pulley in an oven so it expands and would slip on much easier? Don't do enough to know myself but would be interesting to find out. Also I've been told that putting grease or anti-seize on the threads of pullers will lengthen their useful life.

@stevenkelble5248 3 жыл бұрын

Nice video thanks

@sB-yl6di 2 жыл бұрын

I really appreciate the end play part. mine had some and i thought i had a bad pump

@grafduke7485 10 ай бұрын

Awesome video, very clear and this is the same power steering pump I've got on my 2003 Ford Crown-Victoria. Could you please also make a video on how to take out a broken end part of the installer bolt which unfortunately ended up being stuck in the pump axle? I think I probably had bought on amazon a good quality set, but I shouldn't have used the impact wrench for the install process 😢

@PaulHenreid 6 ай бұрын

that happened to me too

@GCraigmile 6 жыл бұрын

Very cool video 👍🏻👍🏻 ... I use the Snap On tool for that. Seems to work better then any other tool so for..

@FordTechMakuloco 6 жыл бұрын

Oh I know the tool you are talking about for removal right?

@GCraigmile 6 жыл бұрын

FordTechMakuloco Its 2 tools in 1.. Snap One is the only one I’ve seen that makes this kind of tool.. It removes it and install it.. I’ll find the part number for the tool

@GCraigmile 6 жыл бұрын

FordTechMakuloco CJ3PSA

@christhefistful 6 жыл бұрын

Great info as always. Would you ever recommend preheating the pulley to make the install easier?

@FordTechMakuloco 6 жыл бұрын

@hatabuly-avto2218 6 жыл бұрын

Hello from Russia! Thank you very much for the next cognitive video! if you could only imagine how I suffered in Russia was looking for a special puller for an American car. I have a Ford Crown Victoria 92.

@danielhowiesr.2593 3 жыл бұрын

Sweet! Smooth riding car. I had a '95 Mercury Grand Marquis. It is built like the Ford Crown Victoria. Loved that car!

@frankgeorge1744 4 жыл бұрын

Thank you. Lol, love tap!

@aspenyukon6845 4 жыл бұрын

04 F150 5.4 3v. 250k miles. Original everything. I run 2cycle oil in power steering.

@garyi2262 3 жыл бұрын

A little heat will expand the pully a little and install is very easy. Pully only! Just do not heat it to much works great and an old school trick

@jamesengland7461 7 ай бұрын

He already mentioned don't heat the pulley. Plastic pulleys expand and contract VERY LITTLE with temperature changes, so you'd be wasting your time, and heat would likely damage the pulley. The small diameter of the pump shaft likely means that even leaving your pump in your deep freeze overnight won't shrink the shaft enough to make a noticeable difference either, but at least that won't hurt anything.

@JJ-nd8tj 6 жыл бұрын

Hi Brian will that puller kit work on the c2 pump with reservoir?? Regards James

@bradballard2538 2 жыл бұрын

Recently changed my pump on my 2010 5.4, where the pump bolts to the block there was only 3 bolts in out of 4. Which actually saved me some time. Cuz the hardest 1 to do was out already. (Someone changed it before). Now I gotta change my pump again after doing donuts in the snow. Wonder if it has to do with the missing housing bolt

@AntonioClaudioMichael 6 жыл бұрын

What was the red case installer kit you used you have a Amazon link for that kit also

@petemiller5813 6 жыл бұрын

With the interference fit so tight between the pump shaft and the pulley. Have you ever heated the pulley to install it to the pump shaft? Your thoughts on this procedure?

@carlosmoreno2387 11 ай бұрын

Awesome 😎

@energyparticle 4 жыл бұрын

thank you

@jerrycremeans2865 5 жыл бұрын

Could you use this tool when you’re doing a 5.4 timing job ?

@ronaldcach2779 6 жыл бұрын

HI, Is this the same pump I have on my 2006 ford ranger [2.3 liter ] ? THANKS FRIEND

@duaneb.1357 6 жыл бұрын

Hello Ford Tech. Ive watched alot of your videos and I currently replaced the PS pump and lines on a 2007 Focus. I can not seem to get the air out of the system. Ive left vacuum on overnight also attached vacuum pump while going lock to lock with engine off. Once I start it it foams instantly. Thanks for your help.

@mike289homebuilt5 8 ай бұрын

you have to get air out, duaneb. Sounds like a lemon car.

@michaelbricker2762 6 жыл бұрын

Need to make a video on replacing the t/y connector on the 2015 5.0 due to leaking coolant.

@dennismwilson9677 2 жыл бұрын

I have a 2002 Mustang GT. Just replaced my ENTIRE power steering system (rack; pump; all lines, except for the one coming off the reservoir with a Y, which isn't available any longer). There's currently zero fluid in my system. What would be the correct procedure(s), in order, to add fluid and bleed air from the pump and the entire system? Thank you. By the way, have watched MANY of your videos - they're ALWAYS excellent!

@ykmalachi 6 жыл бұрын

My puller has the same ground down split collar from those same pumps.

@aboaaskralqahtany5578 6 жыл бұрын

Hi I have a question I can find your answer Can I change the speedbox currently available to new ones with a little more speed and if there are alternative burning plugs that do not break or cause problems such as original burners and this is for Ford Expedition 2005

@j.w.7688 2 жыл бұрын

For vids are very helpful, thank you. Im replacing the power steering pump on my 2001 ford excursion, 6.8L V10. I ordered the pump, but mistakenly ordered the one with the reservoir. Can i just remove the reservoir and still use it, or, do i need to send it back and re-order the one without the reservoir? And guidance would be appreciated. Thank you.

@alexandercarril4486 2 жыл бұрын

I believe the C2 pump( the one with reservoir) has the mounting holes in the front where the shaft is and the C3( no reservoir) has it on the side as shown in this video. Hope that helps!

@roltyd22 2 жыл бұрын

So you can use a 13/16 deep socket and brace the pulley so it wont turn and remove it right? It can be done on the car?

@BFRANTZ1982 4 жыл бұрын

Will the CIII pump run hydroboost brakes, too, with no problem? Does it have enough power?

@huntguy3831 6 жыл бұрын

I put a new pump and pulley on my 99 f150 and the pulley installer from the parts store didn’t have the adapter. I used a socket and a 2.5 pound hammer to put it on. I didn’t beat it but tapped it until it was on. Was that bad for the pump or would it be ok?

@AntonioClaudioMichael 6 жыл бұрын

Will this otc tool kit work on my 2005 ford excursion 6.8l v10 limited 4x4 power steering pump it looks like a c3 the threads in the shaft are 8mm

@joehyundaitech7961 11 ай бұрын

Briancan you include a link for the brass drift ?

@ickess 8 ай бұрын

I have the same pump in my 03 expedition Eddie Bauer edition. I got the cheapo kit like you have and the instructions are totally different. The show putting a button onto the end and then turn the center 1/2 in while holding the larger 13/16th nut in place. Needless to say it’s not working

@TACOMASRT5 5 жыл бұрын

I have a 2001 grand marquis, remote resivuar, bent pully, is this the setup I need?

@chrisroma4201 5 жыл бұрын

Replaced my pump with autozone model.worked for about 50 miles.hit a bump parked truck and now it has no idle pressure .fluid full ,no leaks .bled unit about 2 separate times with a minimum of 20 lock to locks .checked my universals in steering shaft they are fine .at throttle I have steering .no issues previously had to replace pump due to rotted thread on shaft after replacing timing chain and removing pulley for easier pump removal .any suggestions this is a 04 f 150 4.6 .thanks for the great vids .

@mrmustangman Жыл бұрын

autozone stuff is junk....

@jagoss45 6 жыл бұрын

Off topic but I have a Taurus brake question. Any idea why Ford has a different brake hose fitting for the rear passenger side caliper? There’s no banjo bolt and fitting just a straight hose threaded in the caliper. So the only way to get it off is to unscrew the whole caliper from the line. Total pain

@hectorramirez9889 3 жыл бұрын

I have a 2000 Ford v6 mustang 3.8l . I have replaced the recon pinion the steering pump twice all the lines and still has a whining noise. Some one told me to add Lucas that's recommended for a steering pump. Will that help ?

@diasniper101 Жыл бұрын

I just got a dorman pulley and napa pump and it was 5 times harder then what I just watched. Think the last third I'm going have to use a Hydraulic press

@Devo1987 3 жыл бұрын

Will this be the same procedure on a 2005 ford focus ZX4 2.3 Liter ?

@laveritesurlestemoinsdejeh8522 2 жыл бұрын

Of course, almost all the japanese cars have bolt-on pulleys, real easy to remove and install. But, also of course, you never have to do it because they never fail...(or almost).

@TheNightmare692009 Жыл бұрын

I going from 6 rib to 8rib. I hope this can be done with the pump on the motor.

@scottketchum2224 5 жыл бұрын

Thanks man, my pulley is the old style pump and it has that little back and forth play that you said is normal and I was about to change the pump because I have a squealing belt that driving me crazy. I have a 2003 ford Taurus with the 3.0 over head valve and I'm having a difficult time finding the source of the squeal. I can spray the belt with water and the squeal goes away for a few seconds leading me to believe it's a pulley misalignment. I just can't find the source of the squeal.... any idea's on that particular engine???

@nickmansfield1 5 жыл бұрын

Tensioner fault?

@AntonioClaudioMichael 6 жыл бұрын

My pump looks just like that mine is for a 2005 ford excursion 6.8l v10 limited 4x4

@KINGRG1 5 күн бұрын

Will this OTC tool work on an 01 Mustang GT?

@meowmix3525 5 жыл бұрын

Great video but my pulley is stuck on. Used the same kit and bent the attachment 😂. Oh well buy a new one with pulley and maybe high pressure return hose

@bigw8549 6 жыл бұрын

Do you have a recommendation on an additive to put in a 98 Ranger with a noisy PS pump? Lucas maybe?

@007.3l 3 жыл бұрын

Archoil ar 9100(amazon) or hotshot secret fr3 from oreillys

@joshharrison1715 4 жыл бұрын

I have a 5.4 Triton 2004 Ford F150 I replace the power steering pump and now I'm leaking oil somewhere around the power steering pump I didn't put all the bolts back in the power steering pump so I didn't know if it could be leaking from one in the bolt holes any suggestions

@stevek343 6 жыл бұрын

Let's see you change out a water pump on one of those new Ford Tauruses 2010 and up.

@krw5966 6 жыл бұрын

When using an impact to take off the pulley, an amount of grease (small dab) on the threads of the tool, is not a bad idea... actually never a bad idea, even with hand tools.... Thanks for ALL your videos, I have found them so useful!

@FordTechMakuloco 6 жыл бұрын

Definitely I always make sure that forcing screw is lubricated there is allot of pressure on those threads.

@fawxa6762 5 жыл бұрын

Today for the first time I noticed a squealing sound when I turn the wheel to the right. But it ONLY happens when I turn to the right, and am moving. If I’m parked, there’s no noise. Also, if I turn the wheel ALL the way to the right until it can’t turn anymore, the squealing stops. Immediately I thought of the serp belt, but that doesn’t make sense to me because if it were the belt, I would think it would squeal whether I turn left OR right, and also when I’m parked and turn the wheel. Could it maybe be the power steering pump? But again, the left/right issue is throwing me off. The other thing is maybe it’s the steering column itself. But it sounds like squealing, not grinding.

@timothyfay1209 2 жыл бұрын

I am trying to install a new pulley on my pump while in the car, the tool keeps coming unthreaded from the pulley shaft. I suppose it would be much easier on the bench? But I need to install while the pump is on the car.

@adamr3028 4 жыл бұрын

are there bearings on this pulley or when it starts whining bad it's because of the pump only?

@FordTechMakuloco 4 жыл бұрын

Bearings don't make noise on the pumps, it is the pulley system failing in the FEAD.

@johnnyrouse2713 Жыл бұрын

I have a 2005 Ford freestyle steering with easy then hard to turn then easy I already had a wreck here at the house that I had ordered and went ahead and put it on didn't fix it so then I put a power steering pump on didn't fix it only thing else I know possibly could be the intermediate shaft any response would be helpful I know it's hard to diagnose anything long-distance

@williamskelton6751 6 жыл бұрын

I tend to respect my tooling just a bit more by using good grease between puller friction surfaces and threading components. Makes for less stress and longer tool life.

@FordTechMakuloco 6 жыл бұрын

Mine was greased from past use.

@TheKingOfHalo 6 жыл бұрын

Do these rattle when they go bad? The stock pump on my 2000 is leaking from the high pressure thread and rattles at low rpms. For example when I turn the ac or headlights on.

@FordTechMakuloco 6 жыл бұрын

@buckclary3057 3 жыл бұрын

Put new bare pump into freezer couple of hours,then put pulley on very easy,then let pump warm up to good temp and all is well

@FordTechMakuloco 3 жыл бұрын

You still need to press it on so you might as well just get it done and skip the wait.

@catdash4390 7 ай бұрын

Thanks.. at 1:50 why does power steering pumps have shaft end play?

@FordTechMakuloco 7 ай бұрын

Perfectly normal.

@somap8380 3 жыл бұрын

Why can’t we have shaft with threads, for pulleys, which tighten in the direction of the rotation.

@Usmanthemecano 6 жыл бұрын

How to solve the PS noise on Ford rangers??

@Randomgearhead 6 жыл бұрын

show how u install a new Teflon ring on the high pressure side fittings. I hate those things!

@FordTechMakuloco 6 жыл бұрын

I have a video on that too.

@catdash4390 7 ай бұрын

Is shaft end play normal on a 2005 Ford f150 4.6 V8 engine?

@FordTechMakuloco 7 ай бұрын

yes

@kylej8135 6 жыл бұрын

My 00' Mercury Mystique 2.0L (Ford Contour) has one of these CIII pumps. I like driving my Mystique because it is already a rare car to see on the road. It takes a lot to keep mine going (150K). I just got done with a major overhaul: swapped out a bad VCT solenoid, new timing belt, water pump, rebuilt front suspension, new high pressure steering hose, etc. Dropping the sub-frame is really the best way to do a lot of stuff (don't forget alignment pins!). Runs great! I want to buy a SVT Contour as a project car. Even tho the Contours have just about disappeared from the road, there remains a small but dedicated group of people that keep em running, especially the SVT. Check out the KZfaq channel "ForgottenSVT". P.S. I watch your channel a lot.

@king39th33 2 ай бұрын

Is this for ford escape 2008?????

@t.t7225 Жыл бұрын

What kind of grease?

@gjenkins1660 Жыл бұрын

I ordered a new crank and ps pulley, I didn't like how rusted they were, But My threads are just too far gone. Using hand tools it just rips the installer tool out Everytime.