Didn't have a coat hanger so I popped the wire handles off a couple of old paint cans and straightened them. Worked great! Saved $$ and got the job done in about 10 mins total.

Finally someone explained. Been at it for an hour. I appreciate you

I cut up a coat hanger and tried over and over to get the radio out. No one mentions it but the steering wheel on a Windstar is right in the way so it is awkward to begin with. I worked on it for a couple of hours over two days. I could not get the radio to budge. Finally, I went to Walmart and bought the loop tools for about $6. Using these tools I got the radio out in about five minutes. Apparently the radio is tight enough that you have to wiggle it back and forth to get it to come out. And, it is nearly impossible to wiggle it while holding outward pressure on the coat hanger wire because the wire bends. If your radio isn't as tight as mine then the coat hanger wire could work. Otherwise, you'll need something stiffer. The loop tools are stiffer and also have curved ends which make it easier to grip the latches.

dude you just saved my ass cause I couldn't find them tools in my tool box today appreciate it man

don’t know if mines just mean or what cus i can’t get it out to save my life 💀

Thank you very much....saved me a 20 mile r.t. to town and $10.00 at WalMart for tool.....very much appreciated from an "old timer" in Southern Maryland!!!!

Hey. Great video. It really helped me out. I did, however make one modification. I cut 2 pieces instead of 4 and bent them to look like the tool. Made taking out the radio a little bit easier.

Thank you I was thinking about doing that exact thing. I had done it years ago, but I wasn’t sure if you had to have the little nubs on the end of the tool, which was why I was making certain I didn’t need the actual tool. Thank you again

Thanks, i just bought a 2001 Expedition, and it had a stereo in it which was not hooked up, this saved me a trip.

It’s the thick hangars! Thanks bro! It worked great!

Just did it and worked perfectly on my 01 Escape. Thanks a lot dude!

nice one! been struggling getting mine out.. nice tip about pushing them outwards.. came out straight away! 😁

Just saved me a trip to NAPA. Thanks man!

You just saved me a big hassle. Thanks for posting.

Worked like a charm, thanks! The trick is pushing them to the side like you mentioned. Thanks for saying that and for making the video!

Great video. I used filed down coat hanger hooks but any thickish wire will do.

Did it this morning and it works great. I only suggest use the hex keys and a flat head if you dont need to take the pannel off....pop in the hex keys on one side and bend them away from the radio. Then use a flat head to remove one side at a time and boom it comes out ez

93 f350 radio had these holes but a coathangar just wouldn't do it. I had to get really violent with that hunk of junk radio to get it outta there! Ripped faceplate of radio off then with 2 giant pipe wrenches pulled until those steel tabs ripped.

nooo i just got plastic hangers

thanks for the video! saved me a lot of time and a few bucks!!!

Thanks for posting this - I tried the coat hangers but didn't push out ward I will try again tomorrow,if it doesn't work I will try another posters advice with some 16d nails either way thx can't see buying the tool especially since I will only use it once !!

¡Muchas gracias compadre! Great great save my time...and money!

well the coat hangers wouldnt work for me, guess i didnt have any heavy enough. but for anyone having the same problem, four 16 penny nails worked perfectly.

Man, that was easy! I got it first time! Thank you!

Thanks for the advice!!!!! If I had money, I'd pay you lots!

We just did this and it worked great. Ok but first used a coat hanger with too thin of wire which did not work. I was trying on one side and my husband the other and wasn't working. Told him to just do it as we were pulling against each other and it slipped right out :) So the hanger should be thicker. Almost think enough to fit right in the hole. They should only go in about an inch. we also just used a curved wire for each side instead of the four pieces. Hope this helps and thanks for the great video!!!

How far do you insert to engage the release? I used the tool. Seemed like it would go in a long, long way. Pushed out on the loops and disintegrated my radio. Now there's no leverage fulcrum to move out the releases. :(

Figured it was something like that but thanks for the video! A couple of my preset buttons don't work and the volume knob It's crazy when you try to adjust it up it goes down and down it goes up and you've spin it around and it doesn't work in blah blah blah. Finally frustrated enough to do something about it!! Thanks!

Not just engine stuff, but even how to take out the radio, thanks Makuloco!!!

I have seen a few other videos like this but seeing you do it and I've seen you work on the same style truck as mine troubleshooting issues well actually try to use a coat hangers to remove it so buying the tools

Allen keys work also😌

Excellent. To the point video that works.

You just blew my mind.

Thank you that, I thought that would work but I'm glad there was a video so I didn't have to take a chance screwing anything up

I like the idea. I'm gonna give it a try. I'm hoping the aftermarket will work

Thanks mate, your idea worked fine

Very nice. I'm going to try that. I need to access my blend door actuator.

Thanks. Saved me some dough.

You just saved me 20 bucks Edit: It also works with allen wrenches that fit in the holes

Thanks for posting.

God bless you sir. Been wrestling with it almost 2 hours-the hangers worked in about 5 seconds.

Well played, thank you for the tip!

Thank you!

thanks for showing the old factory wire harness plug???

Wow. You.. Are.. Amazing ,where did you get the coat hanger?

the tools work a lot smoother and are under $5 but good explanation on the hangers, They do work it just takes a little patience

I will try this. Thank you. Very helpful. I was thinking that this would work.

Great video. Thank you!

Very helpful thanks!

Thank you so much cheaper then cheap😂 && you saved me time & money which you can’t never get back

thanks buddy!

Managed to remove the radio ok - thanks for your tips with that. Would you know of a reliable site that has the codes that doesn't charge over $20.00? Phillip

Good evening, I think ask this before, can you do a Video on how to fix a 2012 Ford F-150 4x4 XLT 5.0L the Radio quite work I checked all the Fuses and it still won’t Power up, the Clock is the only thing Blinking. Thank You.

I know you posted this a while ago, I'm just wondering would this still work if one clip hole was blocked(past attempt)???

Nice video bro🔥🔥🔥💯

Thanks for closed captions and wow use coat hanger instead damn special tool cost $$$$$$$

very helpful..much appreciated

I have a 2011 Ford transit van with the stock radio. I bought the keys to take it out but it seems the tabs that need to click into the keys are mangeld beyond belief. What can I do to get the radio out without destroying the dash?

Awesome idea! I love it

Thank you for this!

How do you get a touch screen aftermarket stereo out? Obviously it doesn't have the holes for tools like the oem did, so then what?

Wowiezowie! Thanks a lot, since I just learned I needed those tools, haha. So I can hopefully get the last laugh after all.

Thank you for the info!

Great video. Thanks

thanks for the tip. worked, just that easy

You just saved me 20.00. Thanks!

I know this is regarding a stereo, but I have a question about a DVD player in my 02 Excursion. Recently bought it from the original owner, the only thing not working right is the DVD player in the backseat. Tried twice to put in a DVD for the kids and it had enough power to take in the DVD and a quick blip appeared on the screen. Now there is NO power to it and the DVD is stuck in it. I looked through the owners manual to see which fuse is linked to it, but the owners manual did not show. Also I noted that the stock stereo uses several buttons to able or disable the DVD player in back. Since the previous owner has an aftermarket Kenwood stereo installed in front, I don't know if that could be part of the problem or not? I called my local Ford dealer and they said they don't know, and never heard of it. Do you know any likely problems with this, or does it sound like the whole unit is fried and needs replacement? I can't find anything on the internet about specific problems/troubleshooting. Thanks! Julie

Also worked for my john Deere 6125r radio!

So when I want to use an aftermarket what do i need to do to install it?

Hey dude can you give a copy of digram of that stereo thanks for the response

you can also use allen keys

Thank you, very helpful :-)

What year Ranger does this work on? My truck is on its second radio replacement as I bought it second hand. No "four hole" near my radio in my 1990 Ranger! The bezel extends across the driver's side dash past the radio almost to the glove box. Help!

Thank you so much

Happens to have a couple fence ties they should work mint thanks for the video

Will removing the radio reset all the settings? One of the select buttons stopped working and the balance on the radio is set all the way to the back and I have no way to bring it back to the front

where can we get the radio code for same model of radio in the video, is it on the back of the radio? printed card with the radio code is long gone, ford dealer said they don't have any information for anything over 10 years old.

Nice idea. thanks.

Thank you. Good vid

can u put a 2din radio with screen on a ford escort?

Nice video. 👍👍

What if it doesn't have the little holes on the sides like yours does? Then what do i do?

Yep, it helped.

Thank you

Hey. Thank u!

YOU are my salvation on my PU .. THANKS

Any idea how to get the CDs out of a 2005 Ford escape 6 CD player

thank you

Used stakes that you use to put down weed liner

Very cool thank you

Great! Helped me 👍

Good job bro thanks 🤙

Thank you very much for this video. I may have to use this tomorrow and then I will know if that works. Again, thank you.

Welding rod works. Be sure and knock all the flux off the rod and wipe it clean, round the ends going into the holes

thanks!

Did the on my ranger by unbolting the 2 8mm bolts, pulling out the assembly and pushing in on the tabs on either side. Couldn't get the coat hanger to work 🤷🏼 I have a video on my channel

Great vid

You the man!

That was cool😊.

Thank you for this. :)