Fordson Major Tractor Ford 2700 Series 6 Cylinder Industrial engine swap. 120 BHP

Рет қаралды 183,247

14 жыл бұрын

A short video showing a walk around of my Fordson Major Tractor following modifications converting it from is original 4 cylinder 40 odd horsepower to a Ford 6 cylinder industrial engine approx 120 horsepower.
Please see my other videos

Пікірлер: 30

@MarshallSmart 2 жыл бұрын

Nice job on the steel work. Engine sound nice to M.

@geoffgg1075 3 жыл бұрын

Nice job,but your front axle support links need to pivot in line with front mounting pin or will bind over rough ground.

@northshorenative6160 9 жыл бұрын

hats off to the fabricator on this project!!

@vintagelogs 4 жыл бұрын

Thankyou

@vintagelogs 14 жыл бұрын

I am putting a complete new bonnet one,thats if i can get hold of the man who makes them. Im overhauling the whole front end,new stubaxles,bushes, etc and new hubs to convert to steel wheels

@fixitdude74 13 жыл бұрын

Good job, nice and neat!

@vintagelogs 4 жыл бұрын

Thankyou.

@estacionmartinica3092 5 жыл бұрын

I learned in one of those but very good 4 cylinder engine fordson power mejor

@MegaShawy 14 жыл бұрын

Looks good mate, how are you getting on with the bonnet?

@matui6983 Жыл бұрын

Engines hunting a bit and can see fuel dripping from overflow pipe which is never good plus thats an old Trader/Dagenham fuel filter on it but I like the engine swap.

@decnijfkris3706 3 жыл бұрын

Is that hand gas only or did you install foot gas too?

@tomvarcoe3100 3 жыл бұрын

What water pump are you using

@trevordeane3940 3 жыл бұрын

Good engines the P6.

@segundocayupi6036 Ай бұрын

Hola donde encontrar esa maquina

@istp1967 Жыл бұрын

Where can I get one? 😁

@stonenpebble 13 жыл бұрын

Have you had to use a conversion plate or just that 6 just bolt up to the major/super major box? Do you have to make any alterations to chassis or engine mounts? Cheers nice lump sounds sweet

@vintagelogs 4 жыл бұрын

Hi. The engine and clutch just mated up with the backend of the tractor without any modifications. The very bottom lower bolt hole was the only thing that did not line up correctly.

@user-wn1ln1zo8c 3 жыл бұрын

👍

@midgetwarrior958 5 жыл бұрын

I put a 2713e in mine and the bottom 5 or 6 holes sump holes dont match up with the gear box, did you have any issues with this? Im going in the dirrection of welding on some studs or making a plate, what did you do. I take it is a very similar engine? cheers

@vintagelogs 4 жыл бұрын

Hi. It was just the very bottom sump hole on this engine that did not line up. From memory i think we made some kind of clamp, just to add some additional clamping force between the two mating parts.

@trevordeane3940 3 жыл бұрын

There is a kit available to join the P6 engine to the original gearbox in the Fordson Major.

@1liamstar 7 жыл бұрын

What water pump is on this?

@vintagelogs 4 жыл бұрын

Hi. Im not sure what the waterpump was, sorry. It came with the engine when i bought it.

@estacionmartinica3092 5 жыл бұрын

Good moorning Where one for colombia whic envíen has atte My name is Efrén

@robinsoncolon8641 Жыл бұрын

Buenas noches por favor requiero unos repuestos para un motor Ford Industrial 703F60)5BA

@estacionmartinica3092 5 жыл бұрын

Cuanto vale para colombia

@MrBONDASS 14 жыл бұрын

hey:-) nice work on this:-) did you use engine from ford custom cab?? do that fit ??i have a ford custom cab engine ,and i hope it fit super major:-)

@vintagelogs 4 жыл бұрын

Hi. I purchased the engine from a tractor puller, he had been using it in a tractor previously, i believe he then swapped this engine for something bigger and with turbo. The engines were originally used in boats etc.