Four point harness install. Make your own Harness Bar and 4 point harness Brackets

Рет қаралды 22,833

4 жыл бұрын

In this video I build the harness bar and lap belt mounting brackets for my 4-point harness. I also give some tips on using a harbor freight pipe bender. It would cost a little over $300 to buy a harness bar and seat belt mounts. Save some money and make it yourself. Check out our amazon store for the parts I was using.
Check out our website: muddybeards4x4.wixsite.com/my...
Amazon Store: www.amazon.com/shop/muddybear...
Barnes 4WD: 10% off discount code: www.barnes4wd.com/?ApplyPromo...
Or use the code “muddybeards” at checkout
Tools I Use, MotivXTools: www.motivxtools.com/
10% off coupon code: muddybeards
Lights I Use: olight.idevaffiliate.com/idev...
10% off coupon code: muddybeards4x4
Yankum Ropes: yankum.com?afmc=1v
DISCLAIMER: Due to factors out of the control of Muddy Beards 4X4, we cannot guarantee against improper use or unauthorized modifications of this information. Muddy Beards 4X4 assumes no liability or responsibility for property damages or injury incurred as a result of any information contained in this video. Use this information at your own risk. Muddy Beards 4X4 recommends safe practices when working on vehicles and/or with tools seen in this video. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Muddy Beards 4X4. Be safe! This video and description contains affiliate links, which means that if you click on one of the product links, we receive a small commission. This helps support the channel and allows us to continue to make videos like this. Thank you for the support!

Пікірлер: 40

@mattboyer7812 4 жыл бұрын

I appreciate the fact that you use realistic tools and equipment. Great video and tips. Thank you!

@MuddyBeards4X4 4 жыл бұрын

Thanks🤟🏻

@phillippearce9680 4 жыл бұрын

Looks good!

@rocklanderoffroad Жыл бұрын

creative fab work, and it looks great too!

@MuddyBeards4X4 Жыл бұрын

Thanks

@IAmMrTrumpet 4 жыл бұрын

Awesome info! Thanks!!

@PaulKaiser42 4 жыл бұрын

Great video Kelly!!! I like the rapping method as well.

@MuddyBeards4X4 4 жыл бұрын

Thanks👍🏻

@piasprojects 4 жыл бұрын

Great fabrication job. I really like that setup! Down the road if you can do a long term review on the harness that would be cool.

@MuddyBeards4X4 4 жыл бұрын

Thanks👊🏻

@16guns 4 жыл бұрын

Awesome.

@TheBeardedJeeper 4 жыл бұрын

Lookin good man

@MuddyBeards4X4 4 жыл бұрын

Thanks👊🏻

@Rick-4552 4 жыл бұрын

Jobs like these make me wish I had a plasma cutter, those cuts woulda been so much easier

@MuddyBeards4X4 4 жыл бұрын

Yes they would. For sure

@MrMrsregor 4 жыл бұрын

Rick 4 years ago I bought a $300 simadre 50dp plasma cutter on eBay. Cheap, but still cuts very well and I can easily buy more consumables since it is a common style torch head. Definitely worth the $375 if u looking for an inexpensive plasma cutter

@stevenb320 2 жыл бұрын

My question is what bracket do you use if your jeep wrangler doesn't have a roll bar anymore but want to add the seat belts. Also the seats are Corbeau with the open slot at the top similar to the seat you did for the racing belts

@kyleburgess6475 4 жыл бұрын

What is the rear seat you are running for your kid?

@Tbmx8 4 жыл бұрын

That looks amazing man👌🏻 I’ll bet it feels way safer off road with that harness than with the factory seat belt. How hard is it going to be to get in and out of the back seat? Also did you account for the jump seats/forward and decline of the seats? Love how you made everything yourself.

@MuddyBeards4X4 4 жыл бұрын

@Tbmx8 4 жыл бұрын

Muddy Beards 4X4 it’s worth it in my book! I took the back seat out of my Tj years ago. More room for tools.

@SWBCrawler 4 жыл бұрын

Love it man. One question though. I've got an LJ, and i've been thinking about putting a harness bar in the front, and doing the same pass-through you did. However, i hesitate, because my Kids ride in the back. I think getting the kids in and out would be a flat out nightmare with the harness bar in the way. I see you still have a back seat in there, how is it getting small humans in and out of the back?

@mikeestrella2 4 жыл бұрын

I'm interested in the harness bar myself and maybe one for the rear seat as well but have the same concern my 10 year old getting in and out. Also I have a hard top witch only gives you 2 entries through the hatch or lifting the passenger seat no side entrance like a soft top

@MuddyBeards4X4 4 жыл бұрын

Thanks, to be honest I didn’t really think about back seat access or tilting the seats forward for rear access and yes it’s a pain, especially with the soft top on, I can’t just reach or climb through the side, lol. I guess you just have to decide if the inconvenience is worth the upgrade in safety offroad. I do have a back seat but the kids don’t go very often, and most of the trails I do are pretty tough we’re I wouldn’t take them anyways. I am almost on the fence of making mine a 2 seater and putting my spare in the back instead. I don’t have a solution you just have to figure out and decide what will work best for your family.

@SWBCrawler 4 жыл бұрын

@@MuddyBeards4X4 that's about what I expected. :P I'm considering an angled or looped tube from the side bar on the main hoop to the upper bar. Leaving the middle open. Then the kids could crawl between the front seats. But even that doesn't sound great.

@mikeestrella2 4 жыл бұрын

@@SWBCrawler I'd like to see what you come up with cause I'm wanting to install a 4 point harness at least cause my ( scat ) after market seats have been in for the past 3 years and never set in belts

@SWBCrawler 4 жыл бұрын

@@mikeestrella2 whenever I get it done. It'll be on my channel. But right now I have no idea when that might be. I'll either get the rock hard bars. Or fabricate some up once I invest in my own bender.

@grant3053 4 жыл бұрын

Got a video of the rear seat? What seat is it? I’ve got a 3yr old and want a good kid/child seat he can grow with after the child seat

@MuddyBeards4X4 4 жыл бұрын

I don’t, maybe I will do one eventually. It’s a beard suspension seat I got for $100 at a swap meet. Just used a Jr dragster 5 point harness and bought a $7 booster seat on OfferUp I modified to run the belts through it. Works great. Also fits a full size human pretty good too, with the factory seat belt.