Foxbody Parachute Install: How to Perfectly Drill your Parachute Mount through your Bumper

Рет қаралды 24,838

4 жыл бұрын

Drilling a hole through your pristine paint for a parachute mount can be a daunting task. Nobody likes sending things to a body shop, and definitely nobody likes to have things not look pristine on their ride.
This process can apply for any Mustang, Camaro, Corvette, S10, Silverado, or anything else with both plastic or metal bumpers!
Our proven method of getting the hole drilled perfect works EVERYTIME! Watch as Doug walks his way through the process and shows you how easy it can be with basic tools everyone has.
Needed tools:
-1/4" drill bit or slightly undersized
-1.5" Hole saw with new pilot bit
-Blue Painters tape
-Sharpie
-Optional: Toilet Paper roll for tracing
To see all of our parachute mount options click
www.motionraceworks.com/colle...

Пікірлер: 22

@cuttingedgehydrographics2134 4 жыл бұрын

Good video. That could save a few bumpers from destruction.

@adamfisher6560 2 жыл бұрын

Method works great. Perfect fit on my fox body.

@jcnpresser 4 жыл бұрын

Awesome tip! My dog’s name is Remi also, well Remington, but we all call her Remi.

@MotionRaceworksOfficial 4 жыл бұрын

jcnpresser heck yeah!

@kevin_nagle 3 жыл бұрын

this was great! thank you

@BlueCollarBachelor 4 жыл бұрын

cut a C shaped section of the next size up pipe longer than the gap. Rotate it around as you mark it holding the C firmly to the stub receiver.

@tubbedrx2 2 жыл бұрын

Great tips thanx

@BBBILLY86 4 жыл бұрын

I just put yellow or white paint on the mount. Press bumper cover against it. Pull cover and drill out the circle.

@zacharyblum9862 2 жыл бұрын

Could you also tow a drag week trailer with that parachute mount on the fox?

@michaelmerrill589 2 ай бұрын

Do this install on a s10.

@billbushman6686 4 жыл бұрын

Awesome tip! Couldn't you cut the toilet paper cardboard the same length as the receiver (more stability), slide it over the receiver before you put the bumper on, then slide it out to the bumper for marking? Then you wouldn't be fiddling around with a 3/4" piece of cardboard up underneath and behind the bumper. This might be another reason to hoard toilet paper!

@vincentdelucia8078 2 жыл бұрын

What about doing the measurements. Any tips. I have a 96 Saleen, so the bumper needs to be dead on. Thanks

@LSXvoodoo 4 жыл бұрын

👍🏻

@blackwellm23 4 жыл бұрын

Where can I purchase the push on- off button that is on the blue 6th gen camaro in the beginning of the video

@tomscobra2003 4 жыл бұрын

Do you make a kit for 87 g-body regal grand national?

@ClumsyGamerGuy Жыл бұрын

Om the 99-04 sn95 mounts what is the bend on the rear where the parachute mounts to?

@vincentdelucia8078 2 жыл бұрын

Obviously I cannot take measurements from underneath, for the Saleen bumper hangs quite a bit back. In fact, it zip ties into the gas tank straps. If you worked on one, then you obviously know what I'm talking about.

@shawng7902 4 жыл бұрын

Very funny. Uploaded on 17th pre- CHARMA-GEDDON. No one has tp rolls now! Have an unopened case of quilted northern (top shelf) that I'll trade you for a billet vc breather set??