I love the look of the carrier aircraft. I'd be delighted to see a video showing how it was built.

Besides re-thinking whether carbon is necessary, make sure that the video TX antenna is parallel to the RX antenna. I have seen many people trying to fly high altitude close to them selves with linear antennas pointing straight up/down. That obviously don't work. Also.. Don't be shy to take a step back if you have issues instead of forcing a launch. A landing would have made less damage than a failed attempt. Add skegs to the carrier plane so you can land it with the payload attached. Looking forward to Version 3! Keep up the good work. 🙂

The carbon fiber is highly likely to have blocked the RF signal as you suspect - some people over in the high power rocketry space have had similar problems with telemetry radios when using carbon fiber. The carbon fiber effectively will behave as a 'faraday cage' or 'shielding' (depending on construction) and totally mess up the signal. Love the project though, hopefully attempt three will work out!

the big lifter plane is awesome, i like the design and inspiration well done

Great to see y'all still out there flying!

You just know there’s got to be a guy in Ukraine whose only job is to watch KZfaq videos in order to get new ideas for weapon systems.

The lifter looks like a prop version of the stratolaunch, and works great too! Can't tell if it's brown readiboard or cardboard but either way, it's a great idea for a cheap b52.

The carrier airplane looks amazing. Definitely would like to see more of it.

this is so cool, excited to see more

Very cool! Just wondering why is some of the HUD footage blured out? Altitude laws being broken?

I can see something like a hotspot on the carrier (big antenna and payload) linked to the FPV rocket plane to get a better signal at the most critical point when you are lining up and hitting power.

Very cool, subscribed to Team Legit! On much larger scale things I've worked on we used a fiberglass nose cone since the rest of the structure was carbon fiber and this gave us the largest signal view through the fiberglass. I know you mentioned the previous rocket jet was fiberglass and this one was carbon fiber and you're aware of the issues with CF, though maybe I missed where you mounted the antennas or if you blended between fibers to try and help signal clarity. Additionally I'd suspect if your antennas are mounted on the bottom and away from the nose then you'd get interference from the vertical stabilizers.

Antenna signal can't really penetrate through carbon fiber, however in fiberglass it can penetrate no problem as if its not even there. Make a window for the antenna or place it outside if its going to be Carbon fiber again.

Great and adventurous video! Reminds me on David Windestals FPV to space and back ;)

I can atest to carbon fiber blocking radio signals. have a CF skinned glider that would loose control at about 300 ft from the radio, till I drilled holes and moved the antennas hanging well outside the hull. now there is no range problems. The experts claim CF will not do this but I have an airplane that has this problem with it blocking the signal at range.

Loved this video, liked and subscribed 👍👍

A detailed look at the build wold be great. Sorry if you posted that already.

great work, good stuff, reminds me of the virgin galactic design, I am amazed at how good the carrier airplane was performing, well done indeed next time the rocket plane will work, too, I am sure. now that you know another detail to watch out for, you can test for it before the flight, even. great attitude ❤, keep it up

Why not use an antenna wire that wraps all the way around the wing to ensure a signal at any orientation?

I'm new here, but I wonder about adding a deployable parachute for moments like this when there's no hope of recovery. Seems like it might prevent total loss?

Have a try the new fimi manta, you will love it.

Thank you for adding colour to our world. I love a dose of competent absurdity in this mindless TikTok age. Good luck going forward!

awesome project, that plane looks really cool 🔥

Very nice design whatb flight controller do you use ?

can you discuss the mixing and handling properties of the split V tail mother ship? yea, the carbon will kill signals unfortunately.

It might make sense to setup your FPV aircraft on the ground and do a walkout video test. Every 50 ft, check your video signal with a clear line of sight to your VTX. If the carbon fibre blocks or interferes with RF as the folks here in the comments claim, it would have immediately popped up as being an issue to address. External antenna, higher gain, etc.

Nice video! Why not launce the rocket plane upright rather then upside down?

good luck guys.

Nice work guys...

Fun project! Where do you guys launch/fly?

keep working, the world is watching.

I like the split V-Tail! Never seen anything like this before!

They have come on quite a bite since the only Ritewing Drak launch... changed so much since I remember!

Thanks Rutan

Great recap. I'm getting started on v3 ASAP. No carbon fiber laminate this time ...

I think that since the video gradually disappears, it is rather an excess of heat for the VTX, it must not have had enough air flow..

Yep, you dropped it, good job.

As someone who has done rocket-planes in the past, I feel your pain.

Hell yea! Rocket plane/jet with pov GoPro VR stuff and a little dude cutout for the camera in the cockpit 😂

CF is very conducive so proper antenna and placement are very important.

Just curious, the rus airfield strike was done by your plane😊

I've flown my 40 sized R/C aerobatic well past the point of visual orientation many times just for testing new antennas, receivers or just for fun to test my ability to determine it's orientation. As I got better at it, I'd climb until I couldn't see it or I ran out of fuel, just to glide it in. A max altitude recording altimeter showed me at over 1500ft one flight which was the point of loosing sight altogether of the A/C. Most of these altitude tests were 1200-1300ft in altitude. You could always see if the wings were level and to determine if it was upright, just push the elevator, if it dives, you're upright, if it climbs, you're inverted. You could see the wings disappear, then reappear as you rolled over to level flight. The fun part was to kill the motor and glide back to the field. You could stretch that to ten minutes if you wanted, but a last-minute dive from around 500ft and energy management to a landing at my feet was my "show off" signature move. All this was practiced on a relatively inexpensive model, giving much more confidence for flying my large scale A/C. If I were doing what you're attempting w/ a dropped Rocket powered A/C, I'd practice some high altitude flying on something less expensive first.

Very cool can’t wait

very cool!

Carbon fiber is conductive. It will absorb and block all RF from HF to X-band. The carbon fiber body completely detuned your antenna. This is just basic stuff, but I guess many people are not aware of this.

does this plane use the motors off of the carbonZ Cessna 150 because this sounds exactly like my old plane

How come you guys aren’t using iNav or ardupilot? 😢 for the 2nd run, hope you get back in the air soon !

if you are using a fun jet you already know they fly well, so it something you are doing which is causing the crashes if it is unpowered. get rid of the carbon a strengthen it with a stronger spar if you need to, these have been tested way above 150 mph so speed wont be an issue, keep it closer it was way to far away to see what its doing.

The lifter plane is awesome! That would make a great long range platform. I really need to get my planes back in the air. I see you to suffer from the blurry altitude symptom 😊

To bad but always a pleasure to see your videos looking forward to next one Take Care

nice design! FPV to Space, when?

"Split" V-tail.... nice adaptation! :-)

Very interesting

we used to do this in middle school. im not sure how things keep going wrong

Liking that lifter plane design!

Awesome project, would be amazing to see it succeed. Did you consider using RHCP antennas on the carrier setup and LHCP for the payload feed so that you can crank up the vtx power with less risk of interference? Linear antennas could also be worth looking into for the rocket plane as they would be easier to mount for aerodynamic reasons, but they are sensitive to alignment between the transmitting and receiving ends.

Carbon fiber isn't just conductive (not copper conductive though) which has a shielding effect (like a poor faraday cage). It's behavior at different frequencies is very interesting as well. It has a decently high permittivity at the frequency of your video transmitter, leading to an absorbing effect. Some of your video feed wireless power is absorbed in the airframe and turned into heat, meaning less signal. CF in an airframe like this will continue to be trouble for your control/video signals. You should have less interference at lower frequencies if you stick with it, so you could go to 433MHz

The drop system seems to introduce a roll. Don't know if this will be a problem or not. Cool project!

Nice project collaboration. Wonder if having dual antennas (top/bottom) would aid in video quality with carbon fibre? BTW: did notice the rocket-jets elevons in an inverted down position. Having a bit of down (ie: up) on release might have resulted in a more horizontal glide at separation. Good luck to test flight #3!

Wonder if you guys could help me. I was thinking of trying an airborne relay for fpv. Something like a 5.8ghz tx on the fpv and a 5.8ghz rx on the wingtip of the relay aircraft connected to a 2.4ghz tx on the other wingtip and a 2.4ghz rx on the ground

Excelente

What size rocket motor?

I don't understand why it was necessary to mount the rocket plane upside down. Since the plane was dropped before firing the rocket, there wouldn't be a problem with the vertical tail fins hitting the carrier plane upon release, and you wouldn't have to worry about an upside down video feed, nor interference between the antenna and the wings.

Ian are you kidding me I can’t believe you guys did this wow

_"made of laid-up carbon fiber"_ Could this have anything to do with the video problem? Gold star to the mother ship, she was solid as a rock the whole flight! Maybe double-up the number of rubber bands, but other than that I didn't see any issues - Nice!

that lifter is really beautiful

Can we get the specs on the plane? Power length. Wing cord and motors/props? Also why are the motors mounted on wings and not in fuselages?

Regarding video quality, my first though with the carbon fiber is that you are heating it up! (it's absorbing the EM radiation to/from the radios). That's because carbon fiber is fairly conductive. Then I thought, "It's fairly conductive... why not just use it as the antenna?". Then I though, "oooooooor, you could just route some antenna wire over the wings/body". I don't know enough about fluid dynamics or antenna design to speak to how well that would work XD

Pretty cool! People see a Stratolaunch, but i see a strategic bomber with a cruise missile like a Tu-95 with an AS-4, lol

Maybe use Arduplane? Launch and put it in loiter, then manual if everything checks out. If it's FUBAR, throw it into RTL. At the very least it'll save the aircraft and you can land it LOS once it comes down.

Any chance of a quick overview at least of the carrier construction?

Have you thought of putting the rocket payload on top of the carrier aircraft. Basically do the 747/Shuttle style launch. This might let you see the control surfaces and video feed before launch, remove the roll maneuver upon launch, and recover both while attached. The only issue is that you would have to have positive lift from the payload wing at the launch speed. Anyway, just a thought.

You could buy my carbon Ultrissimo funjet for a further test! :D

I mean.. Twin boomed V-tail looks fucking amazing, ngl, but why not A? I wouldn't have even attempted this design because I don't trust myself to make it rigid enough. My A-tailed glider is going on its maiden this week, hope it's going to fly well

El Mirage Lakebed and test area.

Range test. Video feed included.

Great project. Probably just need to make a fibreglass body instead of the carbon fibre

Your launch vehicle is a proven commodity. Where can I buy one? The whole kit.

Great video! Can you explain how you went about getting FAA authorization to fly that high? Can't wait to see you guys try this again!

Very poor antenna placement and orientation, especially with the decision to use carbon fiber, since it attenuates RF signals. Antennas were oriented such that the nulls were pointing toward your base station at higher altitudes pre separation. The only way to have gotten a strong signal out of the setup is if you were flying directly toward or away from the base station, which at the drop altitude and location would have meant flying straight up or straight down. Google "radiation pattern dipole" to get an idea of where the signal will be strongest and weakest, but my recommendation would be to go back to fiberglass and orient the antennas 90 degrees from each other with one pointing straight up (assuming you are going to drop from directly above the base station again). And as someone else mentioned, ensure that the TX and RX antennas have close to the same polarization. You want to point the broad side of the receiver antenna toward the craft and as close to parallel to the TX antenna as you can for the strongest signal. Hope this helps. Cool project and good luck on the next attempt.

We also falsely assumed the upside-down omni was causing video issues.

Cool

I have made an aircraft similar to this one to launch things and rocket planes and so on. I have invented a system to couple the two aircrafts, with a 9g servo it can hold more than 2 kg and it doesn't move a millimeter. I have the file to print in 3d, if you want I can give it to you. It is very useful for these projects.

Beautiful project! What about a launch ramp?

Why didn’t you just use digital fpv?

Not sure I understand when and why an FPV drone would require short burst, over powered rocket power?

Wawwwww so no bar linking the tail and the angle elevator and it's still pretty rigid no flex

Do an RF range check next time

carbon fiber and RF do not get along. the rf will couple with the carbon. maybe better antenna placement and a circular polarized antenna might work better

Guys i need another 1.2ghz lotus last time i checked you guys didn't sell anymore how can i get a couple more?

What do pilots do before taking off ... may be next time, follow a checklist.

This video proves the point earth is Spherical 🎉

Have a signal repeater on the mother ship.

Noice.

Maybe a bear Aerospace--future star next for drop?

Hows this legal?

You sale thats plane for war?

Carbon sucks on RC Planes! I recommend kevlar as a cover material, and carbon just for spars and very small crossections, where the greater stiffnes of carbon starts to make sense and dosn´t block the radio. I have an competition DLC made of carbon with a kevlar canopy, and i hate that thing!!! (although it is a very high-performance glider) When you just fly level in thermals everything is fine, but when you do acrobatics the radio cuts out....🤮 So the damm thing hangs on my wall and i fly my selfmade foamcore- paper- composit- wing on a stick DLC. 😆

It needs a decent antenna

"I can't see a thing but drop me anyway"