Building a Solid State Tesla Coil - Secondary Coil (English)

Рет қаралды 6,924

Күн бұрын

This is the first video in the series "Building a Solid State Tesla Coil".In this video, we will build the secondary coil for my new small solid state tesla coil model "Alpha-DR mark IV", which will be capable of generating electrical discharges greater than 1.30m (~51.2") in length.
Some specs about the secondary coil:
PVC form: 102x367mm (~4x14.45"), 1.8mm (~71th) wall
Winding: 357mm (14") of 31AWG PU enamealed copper wire, ~1370 turns
DC resistance: 190 Ohms (Measured)
Inductance: 46.3mH (Measured)
Resonant frequency (with no topload): ~280kHz.
Any question? feel free to comment on.
Featured social media:
👉Instagram: @franzolielectronics
👉TikTok: @franzolielectronics
👉Facebook: Franzoli Electronics
👉Reddit: @franzolielectronics
👉Patreon: franzolielectronics
Donations:(PayPal): franzolielectronics@gmail.com
Camera: Full spectrum Lumix LX100
Audio Recorder: Zoom H1n.
#teslacoil #secondary #franzolielectronics #diy

Пікірлер: 66

@AltAccount-6502 2 ай бұрын

Thank you for going out of your way to make this video more accessible for English speakers!

@edyt4125 2 ай бұрын

This is the most articulate and careful secondary coil I have ever seen wound. Well done !

@cisarvialpando7412 2 ай бұрын

We need this type of videos...

@spaxxor 2 ай бұрын

Tesla coils are so cool. Thank you for posting this kind of video. I'm so excited to see your process in building these amazing machines.

@eliaskoninger9751 2 ай бұрын

Pleace part 2 ;D

@SteffeL2 2 ай бұрын

The TTS is.. interesting to listen to at times, but definitely an interesting clip to watch :) Nice to see the process behind everything.

@mrdesum 2 ай бұрын

Yes, we need more training videos! I understand it's difficult, keep up the good work 😊

@eliaskoninger9751 2 ай бұрын

More of these videos pleace ;)))))

@Electronic4081 2 ай бұрын

I am beyond excited to get a deeper look into your incredible coils! You have already inspired many, including me, but this series will inspire so many more! Thank you!

@Jim_Austin 2 ай бұрын

Thank you for this. I'm looking forward to the rest of them.

@MarshalStirling 2 ай бұрын

Man, this will shock them.

@Dinco422 10 күн бұрын

So much profesionalism, loved it!

@saxon215 2 ай бұрын

Absolutely loved this look inside the construction of these secondaries. I always thought that you sourced these bespoke from a manufacturer as they were so uniform. I look forward to seeing many more similar videos from you, thanks again for making an English version.

@Doktor_Apokalypse 2 ай бұрын

Love this. Cant wait to see the rest of the series. Have always wanted to build my own tesla coil, but I'm not great at following plans but I can follow a tutorial video with ease. Thank you

@storbytronics 2 ай бұрын

I love the use of the heat-set inserts as both mechanical and electrical connections!

@alexandre3388 2 ай бұрын

Absolutely awesome video, looking forward to the next one !!!

@GeoffryGifari 2 ай бұрын

the windings... so clean

@Gelsonbr777 2 ай бұрын

Awesome job⚡

@Electrology01 2 ай бұрын

I really liked this content🤩

@firefly2472 2 ай бұрын

Thank you so much !!

@MrAdzielinski 2 ай бұрын

I’ve been waiting years to see you do a construction video. I love the pcb plate to prevent through arching.

@singrun7618 2 ай бұрын

absolutly

@Thaumatichthys 2 ай бұрын

Nice

@beast_edits_477 2 ай бұрын

Your Tesla coils:nikolas Tesla coils

@uitvinderalex 2 ай бұрын

I also used PVC tube in the past for the secondary windings, but unfortunately it has shrunk (likely due to the extrusion) over the years resulting in loose windings and electrical breakdown. Solution: buy some fiberglass tubing instead, that will likely also have better glue attachment for potting the secondary coil ;)

@franzolielectronics 2 ай бұрын

Oh, this is interesting.. I use PVC form secondaries since 2009 and its still working well. Maybe heating it for a couple of hours, before placing turns can be helpful.

@Shadyinternetman 2 ай бұрын

Quentin Tarantino in an alternate universe

@singrun7618 2 ай бұрын

hey man i would apreciate the great siana sisters theme to see its an old c64 game but anyways its great anyways

@noelandrew3600 2 ай бұрын

will you be providing files for the pcb component and any other downloads for this project? been a builder of SGTC and VTTC but SSTC is one that has elluded me till now. i have been building up suppplies for a build and have the IGBT bricks and most other components on hand, and winding coils is something i have covered, actually working on an auto winder with wire straightener self tentioning. its more the driver circut that i really need to sort, as i really dont know much about driving these big igbt bricks.

@nekrugderzweite8298 Ай бұрын

i really like those videos and im sad that the views are so low campared to the music videos

@samagoncik4536 2 ай бұрын

Hey, how a you ? When will be second video ?

@whyman22 2 ай бұрын

Is there anyway we can get schematics of the circuit boards that you use in these videos or the pcb design

@Deivy.work.w 2 ай бұрын

⚡⚡⚡⚡⚡⚡⚡

@44R0Ndin 2 ай бұрын

Is there a reason why you used superglue on the end caps of the secondary coil instead of ABS cement, since both are of the "same" plastic, you should be able to use the compatible bonding agent, right? Were it me making a coil using this method, I'd probably have reached for the ABS cement that you nearly always find sold in hardware stores (at least in the USA) specifically for gluing together sections of ABS pipe and fittings in drain systems of a house. This stuff creates an extremely secure bond, it's more akin to a chemcial weld than a true glue joint, because the ABS on both sides of the joint is turned partially into a gel by the cement (similarly to how model cement works), and when you join the two pieces you're supposed to twist them against each other to ensure a firm mechanical bond and a hermetic seal (which is the whole point of making a drain system out of ABS pipe in the first place). The only reasons I can think of offhand for not using ABS cement for this purpose are that you either didn't have any (and did have superglue), or that you have either researched or discovered by doing that there is some chemical incompatibility between the ABS cement and whatever material you are using to prevent electrical flash-over on the exterior surface of the secondary coil winding itself (my guess is that it's some form of corona dope, and judging by the presence of the vacuum pump in the background, you might also be vacuum potting the coil, which is a good idea if you can manage it easily enough). I would love to hear your thoughts on this in any case.

@franzolielectronics 2 ай бұрын

Yeah, because the super glue can be easily removed if necessary, without breaking the secondary.

@44R0Ndin 2 ай бұрын

@@franzolielectronics Oh that's a good point, I hadn't even thought of that.

@styrishrodrigues 2 ай бұрын

I have made a sstc watching online videos.. 😊

@sFeral Ай бұрын

Any chance you could replicate the circumstance warned against in Tesla's Wardenclyffe patent where he explains how a frequency shift, after the secondary LC tank is loaded with enough power, can result in a "fireball", whatever that might mean ? I'm puzzled more people have not focused on replicating this, though I'm pretty sure the described conditions could be arrived at coincidentally.

@cheesecake4204 2 ай бұрын

Looks like it could play Metroid Prime’s theme, PRETTY well…

@VicentPerez 2 ай бұрын

😮hahehahahe....⚡🥰

@ANKSU_ULTRAMASTER 2 ай бұрын

Tesla coils seem to not be the best for bass do they?

@L1413_ 2 ай бұрын

Thanks for the video. Can you tell us the total cost of building such a tesla coil? Thank you!

@franzolielectronics 2 ай бұрын

Thats a good question. The most expensive parts are IGBTs and capacitors. The small sized coil of this series, will have an estimated market value of around U$2000. On this secondary coil, the expense was only ~U$12,00

@L1413_ 2 ай бұрын

@@franzolielectronicsOk, so say a high school wants to build one as a project, it’d cost about $2000 total?

@franzolielectronics 2 ай бұрын

@@L1413_ Yep, much more complex things are to come, I started with the simplest part. There are more affordable / cheaper Tesla coil models too

@L1413_ 2 ай бұрын

@@franzolielectronicsI’m a high school electronics and informatics teacher, and as soon as I can find a stable position in a school instead of being a substitute teacher I’ll start a "music using electronics" club for my students, hence my interest. ^^

@theremoteman4504 Ай бұрын

What's the name of resin and epoxy that you used?

@GeoffryGifari 2 ай бұрын

would the resin and coating on the wire provide a degree of capacitance to the circuit?

@GeoffryGifari 2 ай бұрын

and also, what would happen if the soldered disk on the top end weren't included?

@samagoncik4536 20 күн бұрын

Hey when will be part 2

@vegandr.u_mme_rprefRR Ай бұрын

🥹😍🤩 Thank You❣️💖❤️‍🔥

@1701CARA 2 ай бұрын

Can you share the stl files for the 3d printed pieces?

@nihalkbeats 2 ай бұрын

Please make teslas play "Du Du Du Du, Max Verstappen" pls ppls plssss🙏🏼🙏🏼🙏🏼🥺

@senhortesla4381 2 ай бұрын

Boa tarde Fabrício preciso ter perguntado sobre a ponte full de igbts se tiver alguma rede social que posso entrar em contato com você , é sobre os igbts G40N60B3 estou tentando colocar eles na minha Drsstc mais não sei qual diodo reveso ficaria bom neles o Alexandre que te conhece ele falou que você a muito tempo parece que usou desses igbts , poderia me ajudar nesse quesito??

@franzolielectronics 2 ай бұрын

Alguma coisa como "RURG5060". Mas ao meu ver, é inviável. Você pode adquirir bons IGBTs que já possuem diodos de roda livre internos, por um preço próximo do próprio diodo. Usei "HGTG40N60A4D" e "IRGP4063D", mas descobri que esse esse primeiro componente, foi invenção dos chineses. A Fairchild nunca criou de fato haha Para ter ideia, não existe "HGTG40N60A4" com diodo interno num encapsulamento TO-247.