Freightliner Cascadia DD15 DD16 engine EGR valve actuator removal replacement OM 472

Рет қаралды 108,550

Күн бұрын

Warning:
Always use the proper tools and safety equipment to perform this job.
Failure to perform the job correctly can result in engine damage.
__________________________________________________
this process will be similar to all DD13 DD15 DD16 OM 471 OM 472 OM 473 ENGINE from 2009 - 2013.
__________________________________________________
Freightliner Cascadia DD15 ENGINE wiring harness replacement
Coming soon...
Freightliner Cascadia DD15 ENGINE EGR cooler replacement
• Freightliner Cascadia ...
Freightliner Cascadia DD13 DD15 EGR valve actuator failsafe mode problem spn 2791 fmi 14
• Freightliner Cascadia ...
Freightliner Cascadia DD15 engine repair information playlist
Freightliner videos: • Freightliner videos
____________________________________________________
Now accepting support and donation to my channel.
accepting: personal check, business check, money orders, gift cards, gifts, tools, shop articles, etc,..
send your checks or money orders payable to Francisco Amaya
send your support and donation to:
Francisco Amaya
P.O. box 672
Fontana CA, 92334
OR
PAYPAL
www.paypal.com...
(remember to add your address at PayPal donation)
Follow me on Facebook
www.facebook.c...
__________________________________________________
Radio station: 96.7 FM Kcal rocks IE
#franciscoamaya #franciscoamayaDD15

Пікірлер: 183

@vivianjohnson208 Жыл бұрын

THANKS FRANCISCO....I MAY NOT REPAIR IT HOWEVER YOU HAVE EDUCATED ME ON REPAIR SOLUTIONS......YOU ARE GREATLY APPRECIATED

@AleksandarSilwi 6 жыл бұрын

Francisco my friend you should tell people after EGR Actuator replacement, we need to do little bit of computer work , " EGR Actuator need to be programed " overall you are good man !

@davidmoran8539 6 жыл бұрын

Excellent work. As always very thorough explanation.

@llope8231986 2 жыл бұрын

Buenas noches francisco me podria dar una segerencia mi camion tiene el codigo spn3058 fmi 9 ya le cambiaron el egr actuator ya le cambie el delta sensor y el manifold sensor pero todabia tengo el codigo prendido tendre que cambiar el harness por igual o seria necesario actualisar el ecm antemano gracias

@craigoneil142 3 ай бұрын

Thank you. Was very helpful

@stevenliberadzki9160 3 жыл бұрын

You must retrain the egr valve after replacement. A sweep test must be preformed also. Only done Detroit Diagnostics. You can physically watch to see if it sweeps when you turn the key but a manual sweep test and recalibrations is needed in the software.

@preslavgaev8611 2 жыл бұрын

Where is your shop? Can I come to you to work on my truck

@stevenliberadzki9160 2 жыл бұрын

@@preslavgaev8611 no you can not. Contact work only

@larryjohnson6043 Жыл бұрын

Is it necessary to replace the egr actuator on a 2010 cascadia that has been deleted. If so, does the actuator have to be calibered? When replaced? The old actuator has a leak.

@franciscoamayaYT Жыл бұрын

if the egr system was deleted is not necessary

@felipephillips5357 Жыл бұрын

Is the EGR the same as a turbo actuator or a turbo waste gate on a dd 15 ?

@robertocasillas8717 2 жыл бұрын

Francisco Amaya muy buen video el mío está tirando agua del radiador por la orilla del actuator pero está eliminado el EGR al reemplazarlo se tiene que eliminar de nuevo eso o solo lo cambio por otro nuevo ?

@markmattson7439 6 жыл бұрын

Thanks ! Now I know what I'm about to get into...

@user-xi9no5hv2x 6 ай бұрын

What would be the difference because I have a 2015 dd15

@ericcastaneda58 5 жыл бұрын

I have a question i change the part but the actuator valve is hard is not soft like the old one and its throwing a kkt a black smoke from the muffler pipe

@franciscoamayaYT 5 жыл бұрын

Maybe it is defective.

@ericcastaneda58 5 жыл бұрын

@@franciscoamayaYT it was defective it was not working when i put it on it was smoking and lost power stupid freightliner wanted me to buy a new one wait 90 days and they will return mi money back sure like i have 1,070 extra to give them so after 3hrs faithing with them manager replaced it

@mustafamusse648 2 жыл бұрын

I have 2014 Freightliner Cascadia the truck it won’t have power up hill I been told either turbo charge or the Accuatir??

@vivianjohnson208 Жыл бұрын

WHAT TO DO WHEN COOLANT HAS OIL IN IT ON 2012 FREIGHTLINER ?? THANK YOU

@oscararellano6941 3 жыл бұрын

My egr actuator rod does not move so freightliner wants to replace the whole exhaust manifold? I'm confused

@martinmuniz3525 4 жыл бұрын

Que tal Francisco. Seguido miro sus vídeos. Muy buenos yo tengo un problema. Con mi truck es 2012. Con Cummins isx 2013 tengo como mes y medio que le pusieron ese motor. Pero desde que lo pusieron me falla en las subidas. Como que se le corta la fuerza pos segundos y empieza de nuevo. Me ase como unas 6 veces solo en la subida no me da engine light y los mecánicos. No le Allan. Me podría ayudar

@tejinderghotra9831 4 жыл бұрын

Hi Francisco, Just need some insight on a very stupid problem with my 2012 cascadia with dd15. Code is Spn 2791 fail 14 Changed Egr actuator Changed engine harness The code still comes up when I start the engine and start rolling. But then goes away. It happens if shut off engine and start rolling, if i wait a little bit before rolling then no code. Can you suggest something what to look everytime mechanic hooks to the computer there are no active codes. Computer says happened only once when I started rolling and then no repetitions. Any suggestions please.

@TheDm951 Жыл бұрын

Hi I’m having the same problem. Did you resolve the problem I had spent so much money with the mechanics no can’t figure it out😢

@tejinderghotra9831 Жыл бұрын

@@TheDm951 The problem went away after a few weeks but no idea what the issue was.

@libanbeyle6027 5 ай бұрын

I had the same issue three days ago, truck was park for two days, the third day I started few seconds later two check engine lights came on with the spn 2791 fmi18 Emmission system will derete 25%. I reset the power five minutes and then started again no code, I’m driving the third day no code, what’s your thoughts please Thnks

@Armans-World 5 жыл бұрын

Do we need to change the actuator only or the kit because the kit is double the price why can’t I use my old bracket

@GurpreetSingh-nx7rj 5 жыл бұрын

They don't make the older actuator anymore for those motors.. so you need the new kit for 1300

@dontegrissom3343 2 жыл бұрын

My egr linkage seems to move when it wants to. But I am experiencing the problems that you point out in your video about the Delta sensor and carbon build up. Would you suggest replacing the Delta sensor first? And checking the pipe to see if it is clear before replacing EGR Actuator?

@vickymultani8446 3 жыл бұрын

I have 2013 freightliner cascadia before my Truck def bypass and after reinstall all systems one box but problem is code 2791 fail 14 aculator and engine harness already changed but this code still on the screen and my Truck on the road power lose please give me any suggestions what I do

@hddm3 5 жыл бұрын

What socket or wrenches do you have for these trucks. Specialty ones. Like fuel lines those egr pipes etc. thanks man

@franciscoamayaYT 5 жыл бұрын

Nothing special. I use conventional tools for this job.

@alongwang3582 Жыл бұрын

Hello! Can you fix SPN 625 FMI 14?

@dallc4877 4 жыл бұрын

Hi Francisco I have 2013 Freightliner Cascadia and I got EGR Differ Pressure 13 and 00 code, Please let me know what should I do

@johnnieburnett9249 3 жыл бұрын

I have a dd13 with a code egr slow response any ideas thank you

@ZafarIqbal-qe2po 3 жыл бұрын

Wonderful - Thank you

@alvaromartinez5641 3 жыл бұрын

Holla Francisco, I have a 2015 freightliner cascadia with a dd15. My code is 3058/9 and the software is telling me to replace the ECM. How is that making any sense? What do you think I should do? I replace the delta pressure sensor already n nothing.

@kevinsosa866 6 жыл бұрын

great video as always

@veselchaq 3 жыл бұрын

how much coolant gotta be drained?

@prisr31 4 жыл бұрын

Y esa parte es la que hace que no jalen parejo el motor o qué rollo

@gsageorge2008 6 жыл бұрын

Hey Francisco thank you for putting this video together because I found it to be really helpful. No I have a question because I replace the EGR valve actuator just like how you show in the video by the computer keeps flashing a code for the valve actuator motor fail safe and it won’t go away. It seems to me like it’s not detecting the new EGR actuator. Any ideas what to do?

@franciscoamayaYT 6 жыл бұрын

It is possible that your engine sensor harness is bad Check this video to see how to replace it. kzfaq.info/get/bejne/bdGkl8dp1KybgIk.html

@mostwantedtv8790 5 жыл бұрын

Hola francisco, como quitas la parte de atras la egr valve, que medidas y herramientas necesita mi camion esta haciendo ruido de ahi cada vez que presionas el acelarador al soltarlo hace un chiflido de esa parte crep lleva 4 tornillos solamente y la clampa

@j.l.r.384 2 жыл бұрын

A mi me está pasando lo mismo … como arreglo ese problema?

@HayateAzekura 4 жыл бұрын

I have a 2013 Freight liner Cascadia I have replaced, the EGR valve actuator, wiring harness, ECM and new filters I am still getting fault for "egr valve actuator no failsafe mode" I have gotten my truck's ECM updated and I don't know what else to look for. Can you please help

@franciscoamayaYT 4 жыл бұрын

Check the harness plug but sometimes the EGR actuator comes defective from factory.

@btomas225 2 жыл бұрын

@Francisco- I have a 2014 Cascadia with a DD15. It has the delete installed. It has exhaust in the coolant (I did a test). It is losing coolant someplace. Could the O-ring in the EGR valve body cause the exhaust to enter the coolant? Would I see coolant when removing the hose in the manifold from the EGR? I see no antifreeze there now. Dry as a bone. I don't see any external leaks from the EGR either. What do you think? Could it be blown head gasket?

@abnerzarate2231 Жыл бұрын

What ended up being the issue ???

@zeke1eod 5 жыл бұрын

Thanks for sharing, God bless

@martinanaya9311 6 жыл бұрын

Thanks Francisco. Mine is leaking antifreeze from the bottom when the weather is cold. Should I replace it right away o do I have some time. What do you recommend. Thanks again Francisco.

@franciscoamayaYT 6 жыл бұрын

That will depend on the amount of coolant it is leaking. If it is a lot, I recommend you to replace it.

@martinmuniz3525 4 жыл бұрын

De antemano gracias

@cedricdouglas6152 2 ай бұрын

Are you located in Dallas

@laresurrection 5 жыл бұрын

Hii francisco I got 2011 cascadia dd15 I got the same code and we did change the egr actuator. Now i still got same code with both check engine comes on.the one with chek in it is dissapeiring after a few moment and yellow engine light stay son .after the both go off. And come back again...when I check the code it's still 2791 fm14 . Do you have any other idea can cause this?

@Highwayman8 5 жыл бұрын

Ive got the same thing happening. Lights come on, truck loses power, lights go off and the truck runs fine again. I was wondering if i should replace the actuator or not

@franciscoamayaYT 5 жыл бұрын

Maybe the wiring harness is bad.

@TheDm951 Жыл бұрын

I have the same problem I change both the wire harness and get actuator

@Gotro72 6 жыл бұрын

Good job.

@titopotente5453 6 жыл бұрын

Hello Francisco...do you need to use any pipe dope or thread tape on any of the fittings? Thank you

@franciscoamayaYT 6 жыл бұрын

It is better to use it to prevent leaks. I do.

@homegymequipmentreviews5409 4 жыл бұрын

Egr actuator replaced but now there is a SPN 5588 FMI 9 code. It says “CAN 3 communication error” 2014 DD15 Engine. Any idea how to fix it?

@franciscoamayaYT 4 жыл бұрын

I don't get anything with that code. Does it have a different one?

@hoolarzf 6 жыл бұрын

maestro, what are symptoms are bad EGR actuator? does it give you engine light or noises, or what? in what basis you decided to replace that part? or what's the lifetime for that egr actuator?

@franciscoamayaYT 6 жыл бұрын

Yes, it does turn the CEL on and sometimes it leaks coolant. Around 600k miles.

@jaouadzidour2024 5 жыл бұрын

Hey fransisco I hope you doing well, question please, freightliner cascadia 2012 I got amber engine light and check engine light with 2 codes spn 411 and spn 2659 a day after my truck kind of yenky at 1300/1400 low gears ,I did change the egr delta p sensor and the pipe now it's running normal but I still have the same codes ,please help..

@chrishale6117 4 жыл бұрын

What was you spn 411 code ? Did u get fixed? Having same issue egr spn 411 fmi 1

@miguelmendez1638 5 жыл бұрын

Francisco I have this code eng. 2 00 spn002791 supposedly egr valve control or position incorrect and I replaced the actuator but still have the same code

@franciscoamayaYT 5 жыл бұрын

What engine do you have?

@chrishale6117 4 жыл бұрын

Will bad actuator cause spn 411 fmi 1?

@chrishale6117 4 жыл бұрын

Replaced delta p and venturi pipe already

@chrishale6117 4 жыл бұрын

Smokes bad under heavy load then stops when i let it idle nd coast for a minute

@franciscoamayaYT 4 жыл бұрын

Maybe you have a bad egr pressure sensor

@brauliogoris516 2 жыл бұрын

Cuánto es el costo del kit?

@maymusmuhammad9362 4 жыл бұрын

What is the book time on R/R for this repair?

@paulhernandez1432 4 жыл бұрын

Where is the egr vale located on a 2017 frightenliner cascadia

@franciscoamayaYT 4 жыл бұрын

It is in the exhaust manifold and the actuator is behind it.

@prisr31 4 жыл бұрын

Her carnalito. My 2010. Cascadia eel motor se oye así como si se acelera y se baja. Es por esa parte o qué rollo.

@franciscoamayaYT 4 жыл бұрын

No, vea este video para esa solution kzfaq.info/get/bejne/l7Byfc-WysuqiIU.html

@Foolish_activities 2 жыл бұрын

Lifesaver #SalvaVidas 🤧

@DementiaJoe91 4 жыл бұрын

Hello, so I recently had this code spn 2791. I replaced the egr actuator with a new style one, the check engine lights went away, but after driving about 15 miles the same spn2791 and check engine lights came back on.... any idea what the problem might be? Any help would be greatly appreciated

@franciscoamayaYT 4 жыл бұрын

Probably you need to replace the harness

@arthardy8716 4 жыл бұрын

My EGR stays in failsafe mode after the EGR has been updated. Any suggestions?

@franciscoamayaYT 4 жыл бұрын

It is possible, but also can be caused by a bad wiring harness

@marcusjones1082 6 жыл бұрын

Francisco, what kind of tool did you use to remove the pipe where it connects to the block (maybe it connects to the egr cooler)?

@GurpreetSingh-nx7rj 5 жыл бұрын

It's to the block and your use a crow wrench socket 3/4 or 19mm

@prisr31 4 жыл бұрын

Hey Francisco. Mi troke me está dando. La Luz de el egr control valve. Anormal update rate que significa. Y que tengo que remplazar. Hay si me hechas la mano por fa

@prisr31 4 жыл бұрын

💡

@franciscoamayaYT 4 жыл бұрын

Que el numero de codigo y el año y model de motor

@prisr31 4 жыл бұрын

Francisco Amaya no se l código pero es un dd15 2010. Cascadia Se lo que dice por qué tengo el. Bluetooth que se llama. Nexiq. Conectado. En le troke. El mini. Sabes.

@adolforodriguez5911 6 жыл бұрын

buen video..pero no le entiendo..me gustaria q lo hiceras en tu idioma..gracias.

@jesusvillanueva2289 4 жыл бұрын

You don't have to relearn the egr actuator ?

@franciscoamayaYT 4 жыл бұрын

No, you don't

@bengonzalez7678 5 жыл бұрын

Francisco , I have a 2013 freight liner cascadia DD15 starting losing power off and on fault codes injectors 1,2,3 so we had injectors rebuilt still same issue soon as we drove it about 30 miles check engine light on again and lost power we replaced outside harness and inside engine wires. Engine light Will go away if we shut truck off wait 5-10 min and will run fine until 20-30 miles and will lose power again and check engine light on. Still have injector 1,2,3 fault codes. Not sure what to do now. Any ideas what else it can be?

@franciscoamayaYT 5 жыл бұрын

What is the code number when this problem happens?

@joshsims2061 5 жыл бұрын

Ben Gonzalez when they rebuilt or replaced injectors did they replace the injector harness for those injectors.. usually if you pull the first injector harness connection you see oil inside I would bet the harness is bad.

@joshsims2061 5 жыл бұрын

Or you have a bad MCM

@crisanocj 4 жыл бұрын

Hola, tengo en spn 3058 fmi 9 , delta p sensor nuevo, que puede ser? gracias?

@franciscoamayaYT 4 жыл бұрын

Que motor tiene?

@franciscoamayaYT 4 жыл бұрын

See codigo piece ser por lo sifuentes Valvula egr mala Delta p sensor malo Bloqueo en el flujo de egr

@giovannisocci8793 5 жыл бұрын

Francisco,I noticed black in my coolant reservoir,and noticed pinkish (coolant color) around the egr actuator,plus coolant is being pushed out out of the reservoir thru the top cap...Would replacing this stop the blackness in the reservoir? I thinks is exhaust fumes.

@franciscoamayaYT 5 жыл бұрын

The most common cause of the black material in the coolant tank is the oil cooler seals. The coolant leak in the EGR actuator is a bad EGR actuator

@giovannisocci8793 5 жыл бұрын

@@franciscoamayaYT I ll have it looked at by the tech,the egr stopped leaking,but the coolant is going into the reservoir overflow part of the tank,but the coolant level is at normal level,and coolant is still being pushed out thru the reservoir cap...too much pressure I guess.

@giovannisocci8793 5 жыл бұрын

@@franciscoamayaYT Prior to this,I had the oil cooler replaced,bc I had lots of oil in the coolant/reservoir,but I never had temperature issues,I flushed it out until it was clean,replaced the reservoir and coolant as well. Then the reservoir got darker,but that could be bc as much as I flushed it out it,there must be oil residue left in the cooling system,enough to darken the reservoir. But what worries me is the coolant going into the overflow and out thru the reservoir's cap...could it be back pressure? but there are no overheat or abnormal temp issues.

@franciscoamayaYT 5 жыл бұрын

Have you tried replacing the cap?

@eidayal 3 жыл бұрын

How do you perform the relearn egr?

@franciscoamayaYT 3 жыл бұрын

For the 2015 and up, you need the DDDL software

@carbombtorres1761 6 жыл бұрын

Vas hacer mi mejor amigo

@rero6212 6 жыл бұрын

Hello Francisco, do I have to clear the codes after installing the actuator?

@franciscoamayaYT 6 жыл бұрын

Yes

@stevenliberadzki9160 3 жыл бұрын

Once you finish the replacement you'll have to dive into dd and preform recalibration. This driver waited to long a regen was needed. Remember regens are only supposed to be for diagnostics if they are completed in a manual mode. All others like passive the truck does it for soot removal.

@michaelgriffin1179 4 жыл бұрын

How long does it take to complete this job ??

@franciscoamayaYT 4 жыл бұрын

Around 2 - 3 hour. Sometimes can take a little more when you have problems removing the bolts.

@donaldglover4627 5 жыл бұрын

My truck needs this, it's at the dealership now and they quoted me $2,400 for the job 😔

@-tinayoufatlard-5814 4 жыл бұрын

Cash_NYC where’d you buy the kit? Freightliner told me $1400 today. I’ve tried ordering a used one but came in broken.

@loganamo 5 жыл бұрын

Francisco Great video I have learned a lot from your post. My question is I keep getting a code EEC 061 SPN 4364 Nox conv EEF 18 I replaced both intake and exhaust and two weeks later the same code popped up. Wht is ur Recommendation. Thx.

@joshsims2061 5 жыл бұрын

maurtice logan need to have your Nox sensor checked for bias sensor.. If you have the diagnostic link you can unplug the Def doser electrical connection and run a low temp ATD and make sure that the sensors are within 50ppm of each other.. usually you have replace the outlet Nox sensor. Other issues has been def build up around the def doser you could also fix this issue by burning off excessive def with it also unplug.. but you will have to figure out why it’s using so much def or issue will come back.. good luck

@codyspencer-leahy3513 4 жыл бұрын

where is your shop??

@NomadChad 5 жыл бұрын

What are the signs of a bad EGR Cooler?

@franciscoamayaYT 5 жыл бұрын

Losing coolant and exhaust gases leak

@stevenliberadzki9160 3 жыл бұрын

Take the clamp off and look into the egr or connecting pipes near. If you see a buildup replece it. They have kits to clean it but it doesn't work.

@cosme2032 4 жыл бұрын

Why did you replace?

@franciscoamayaYT 4 жыл бұрын

It was stuck close

@cosme2032 3 жыл бұрын

Eres Chingon

@capsula2007 6 жыл бұрын

THANK U BRO. Is it worth to buy this cascadia DD15, DT12 with 320K miles that it had these issues and fixed already with:engine head gasket oil leak, flywheel housing gasket oil leak, front cover gasket oil leak, high pressure fuel pump leak from mounting O RING, rear oil galley plug leak, coolant leaks from DEF header coolant line pfp, coolant leaks at DEF tank area...would this truck be reliable for the future? If the head gasket blown out caused some other compenents to messed up and it will have problems in the future...any true answer I will appreciated

@franciscoamayaYT 6 жыл бұрын

What is the year of the Cascadia? No, DT12 automatic transmission is not reliable. I will recommend me you a conventional Eaton Fuller manual transmission to prevent problems.

@capsula2007 6 жыл бұрын

Maestro, this truck is 2014. Do you still think the same or 2014 year is better for automatic? thanks

@franciscoamayaYT 6 жыл бұрын

I think the same for all automatic transmission, they are nice when the are new but used truck with AT is not very reliable. Anyway, it is up to you to decide. If you really want a truck with AT, I recommend you to get the service history of the transmission so you can know if the transmission was serviced in the past.

@jorgegrealty 6 жыл бұрын

What did it cost parts and labor?

@franciscoamayaYT 6 жыл бұрын

Around $1400, just the EGR actuator kit cost around $1000 but if you need to replace it on the future the EGR actuator itself cost around $600

@simuljustusetpeccator5547 4 жыл бұрын

Easy breezy

@elviscocho9256 4 жыл бұрын

Más videos en español

@ovidiofs1 5 жыл бұрын

Too much maintenance I think, prefer epa 98 mbe 4000 the best engine ever made

@fieri67 5 жыл бұрын

how much the mechanic wants for this job ? any one knows ?

@CarlosMartinez-dh9zl 5 жыл бұрын

$2800 dlls is the answer to you question, for replace EGR valve so you can do it and save a lot money parts is 1400 dlls

@jamesdavis7473 5 жыл бұрын

Do you have an video on how to calibrate actuator?

@franciscoamayaYT 5 жыл бұрын

What actuator?

@lemuelwest404 4 жыл бұрын

That clip ain't that easy

@joka503dagamer5 5 жыл бұрын

“V” side to valve or actuator?

@martinanaya9311 6 жыл бұрын

So you don't need a computer to set the actuator?

@franciscoamayaYT 6 жыл бұрын

No, it is not necessary, you need to reset the self learning data but it is not mandatory.

@cactusjack1806 6 жыл бұрын

Francisco Amaya reset self learning data? How is that accomplished? I recently changed my actuator and I'm still getting this code intermittently- eng calib 128 411 13. I'm thinking I need to clean the delta P or have the ECM reset.

@franciscoamayaYT 6 жыл бұрын

You need to replace the EGR delta pressure sensor and perform a calibration with the DDDL software.

@cactusjack1806 6 жыл бұрын

Francisco Amaya thank you for the reply! I removed the delta P sensor and the port holes were completely clogged with soot. After cleaning those out the truck runs completely normal now and no more codes.

@bloodflow7238 6 жыл бұрын

Hello sir. I'm getting EEC 061 spn 4335 DEF pressure 01 Can I help me out and let me know where I can start off. Thank you

@franciscoamayaYT 6 жыл бұрын

The codes means: no def air pressure from supply. This could be a problem with the def air limiting valve

@bloodflow7238 6 жыл бұрын

Francisco Amaya copy!!! I got that part You're talkn about the DEF pressure limiting valve right?? If so. Once I replace it, will the code go away? Or do I have to get it connected to the software and get codes erased Thank you

@franciscoamayaYT 6 жыл бұрын

You need to do a scr air test with the DDDL software but with some luck it will go away once you start the engine for 5 minutes and then turn it off for 2 minutes and then turn it back on.

@bloodflow7238 6 жыл бұрын

Francisco Amaya cool. I appreciate the info.

@plukas7580 6 жыл бұрын

Oye bro how do you know when the egr actuator not good no more ?

@franciscoamayaYT 6 жыл бұрын

It will give a fault code or it will leak coolant.

@musheghhayrapetyan8982 6 жыл бұрын

I had a truck that was building excessive soot in venture pipe and it was closing delta p sensors holes. After 3 months of headaches I found that stupid actuator is faulty. I had no codes. So what needs to do. Remove big pipe that goes to one box. Start previously warmed engine and let it idle 10-20 seconds. push down accelerator pedal and monitor the exhaust smoke that comes out from pipe. the smoke will be size of foot ball. it just comes out and stop. if you see more then that, then actuator is performing slowly and needs to be changed. if you see smoke is coming continuously again actuator is bad.

@plukas7580 6 жыл бұрын

I see no codes but the coolant is going low level and already lost a lot of engine power

@benjaminfontanilla6719 6 жыл бұрын

You havce to use laptop and do a egr actuator relearn

@franciscoamayaYT 6 жыл бұрын

It is recommended but not mandatory.

@richardjolley6244 5 жыл бұрын

If I don't do the relearn will my check engine lights eventually go away?

@franciscoamayaYT 5 жыл бұрын

No, no check engine light will come on. Unless there is a problem.

@jorgetorres8250 4 жыл бұрын

Habla español,el inglés no se te entiende.

@thermroberts380 6 жыл бұрын

These trucks are trash. Same things wrong wit all Cascadias. It's an apparent design flaw.

@marcusjones1082 6 жыл бұрын

By all means, tell us which truck manufacturer makes one that lasts forever. Did you think you could run any truck for even 10k miles and not have maintenance issues? It's no wonder you didn't put your name there.

@thermroberts380 6 жыл бұрын

Marcus Jones, more than a maintenance issue. I'm guessing you don't own one, and if you do, I can tell you exactly what you've replaced already, or going to replace in the near future. If the same thing breaks across multiple units, then it's a design flaw. Plenty of people can attest to that fact. Sure, every truck needs repairs on a regular basis, but when the egr actuator fails on at least 80% of Cascadias, then it becomes very apparent what the problem is. And what the fuck does my name have to do with anything?

@marcusjones1082 6 жыл бұрын

CROWN ROYAL, you guessed wrong. I do own one, and I love it. But you have to take care of it, and you have to treat it like you want to keep it for a while.

@thermroberts380 6 жыл бұрын

wrxassa, man fuck you. You don't know shit about me or my abilities as a mechanic. Go find you somebody else to play wit..

@eltllcllc5925 6 жыл бұрын

just a note to Marcus Jones my NEW EGR actuator failed after 2 years I didn't want to believe it, cleaned my filter, EGR valve ports but still engine lite finally changed the actuator so my point even new part fails per mechanic its the electric part that failed, first time on my old style the coolant leaked it is sad Mr. CROWN ROYAL because these parts cost $500 and dealer wants $900-1100 cant even last 5+ years