Front Fork - Removal & Oil change & New Seals | HONDA INNOVA GARAGE | WAVE | 2010
Рет қаралды 1,373,383
6 жыл бұрын.How to: Motorcycle front fork - Removal, Oil change and New Seals
My full D.I.Y series Video for Motorcycle self mechanic jobs - Service guide And Repair manual:
• HONDA INNOVA GARAGE | ...
************************************************
MyINNOVA motorcycle Souvenir Shop:
teespring.com/stores/my-innov...
DONATION to production an original videos in my KZfaq channel. Thank you very much!!!
www.paypal.com/cgi-bin/webscr...
************************************************
אין לראות בחומרים הנ"ל המלצה לפעולה או תחליף לביקורת במוסך במועדים שקבע היצרן או מכל סיבה אחרת. השימוש בחומר הכתוב, המצולם ובקטעי הוידאו, הוא באחריות המשתמש בלבד. עבודה על האופנוע יכולה להיות מאוד מסוכנת ולהסתיים בפציעה קשה, תאונה אחרת, אפילו מוות.
These materials should not be considered a recommendation for action or replace the garage at the times prescribed by the manufacturer or any other reason. Use of the text, photographic and video clips, is on the responsibility of the user. Work on the bike can be very dangerous and result in serious injury, other accidents, even death.
************************************************
All Good In The Wood by Audionautix is licensed under a Creative Commons Attribution license (creativecommons.org/licenses/...)
Artist: audionautix.com/
Country Cue 1 by Audionautix is licensed under a Creative Commons Attribution license (creativecommons.org/licenses/...)
Artist: audionautix.com/
@wearenotconsumers 6 жыл бұрын
Another thing is to NOT over tightened the front and rear axle nuts. Many failed seals/oil leaks caused by that mistake. Greeting from Vietnam.
@MyINNOVAMotorcycling 6 жыл бұрын
OVER tightening the axle nut will break the axle bolt!!! And if the fracture occurs during riding, the broken axle will destroy the seals , and the entire motorcycle can be destroyed in a motorcycle accident. This is not the over tightening that destroys the seals (because the seals are protect by COLLAR), the tightening is metal to metal, not metal to rubber. The broken screw causes all the damage, which is really dangerous !!! The destruction of the seals is the smallest problem, the big problem is the possibility to body injury include DEATH
@MyINNOVAMotorcycling 6 жыл бұрын
Looking back at the video, I think you're right, I did not notice. kzfaq.info/get/bejne/h55hh8Z6y7C1j2Q.html It seems that the leak is from upper seal that is an O-ring seal. The O-ring held seven years and 35,000km, so I do not think the failure is due to over tightening, although I admit it's possible. very weird. thank you!!!
@maartenja7292 6 жыл бұрын
Great (AAA) video again Tamir. Only 7.000 km on my innova yet. With help of your video's and good maintenance, endless km's to go! Thank you.
@guard4301 4 жыл бұрын
Possibly the best explanation available, thank you
@herbertkunze3610 6 жыл бұрын
Very, very well produced video, vivid and well explained! Thank you, tamirkr. :)
@Darob14 6 жыл бұрын
thx... lov Honda innova may 60 000 km
@hannahfaithmag-aso6779 3 жыл бұрын
Thankyou My dad really enjoyed this.
@roberto3262 4 жыл бұрын
I always work on my forks while wearing my steel toed socks too!
@rolandoruto3647 6 жыл бұрын
good job sir and God bless you
@MrJim7627 5 жыл бұрын
My friend,that's an excellent job.Some details make the difference such as heating bolt removal method or using lubricant on hex bolt thread e.t.c.Excellent job,pro done.I would like to add an ease for kids that will follow these instructions.If you don't have the guide for the seals installation ,you can use a socket with the right diameter and seating surface clean and equal very very carefully.My INNOVA Motorcycling:congratulations,keep walking...
@fostexfan160 3 жыл бұрын
Great video....Need to do the seal on one of my forks on a honda pcx 125. Local Honda dealer wants £48 for a pair of seals and 2 hours labour for the job totaling approx £150....I bought a brand new pair of shocks for £65 and did it myself without hassle changing the seals
@sebatub 5 жыл бұрын
Excelente!! Muchas gracias
@jesselee4405 5 жыл бұрын
Well.............................. That was fricken awesone. Thanks!
@easonwee 6 жыл бұрын
Very great editing n make full use of the screen n time. i like the video n love the last part. tamirkr can be funny too!!!
@peminatduaroda4301 5 жыл бұрын
The most good video bro
@arkadiuszdabrowski7658 4 жыл бұрын
Thank you it was helping for me
@murti517 5 жыл бұрын
Woow what a work and good video tnx
@hickey4747 2 жыл бұрын
Watching this I was just thinking I think buying new one would be cheaper and less cost affective. Am so glad you did that ending. Made me laugh. Great video keep up the good work.
@MyINNOVAMotorcycling 2 жыл бұрын
THANKS👍🙂
@meltedpants8846 6 жыл бұрын
Wonna maintenance my super cub by you) so careful and accurate
@MyINNOVAMotorcycling 6 жыл бұрын
Sorry In each of the videos you will find a WARNING: The films are only for professionals. A person who treats a motorcycle without proper authorization and does not have the necessary knowledge of a mechanic endangers himself, and can lead himself for serious injuries and even DEATH. The use of the videos is on the responsibility of the viewers only.
@M.khan9998 5 жыл бұрын
Nice...
@prakashfulzale7642 4 жыл бұрын
Dekhane se pahle like kiya hai
@georgenikolaoy6887 2 жыл бұрын
Very good job!
@Dolla_7756 2 жыл бұрын
Thank you
@auraautospares9737 3 жыл бұрын
Good work I like it..
@Lamdodienbaychim 4 жыл бұрын
Very good
@shortstroker 5 жыл бұрын
Nice bro..
@BHBAG 3 жыл бұрын
Bahut achha bheya
@r2kgarage 5 жыл бұрын
Nice
@lalaazerty5158 3 жыл бұрын
اللهم بارك لك فى عملك
@MyINNOVAMotorcycling 3 жыл бұрын
الله حفظك
@hannannajmi2955 4 жыл бұрын
Nice video boss
@Goodfarmer369 Жыл бұрын
A Big thank you from VietNam ❤
@MyINNOVAMotorcycling Жыл бұрын
THANKS 👍💖
@sshardchrome 3 жыл бұрын
Nice video, it also works with Kymco People S 50. That upper plug inventor should be punished with 20 lashes.
@elsokhasalemotorcycleservi9418 10 ай бұрын
Good idea
@sharkgaming4035 2 жыл бұрын
very2 good content👍🏻
@salvadorsorgorb6934 6 жыл бұрын
Hey! First of all congrats for your channel i'm a follower of your videos and I would like to ask you where do you get new pieces for the Honda Innova, thanks in advance and greetings from Spain!!!!
@MyINNOVAMotorcycling 6 жыл бұрын
I purchase parts from several different Internet stores, as well as from local suppliers here in Israel. I check prices, and invite where the price is the cheapest, including the shipping price of course. I do not know what the situation in Spain. I purchase parts from Greece, others from England, Thailand, USA and more. One way to find a part is to type in Google its catalog number.
@frank1989115 4 жыл бұрын
Look similar to my Honda lead 110
@loanchi3290 3 жыл бұрын
Nice Video and Thanks. I'd rather buy a new one. I think that would be your conclusion too. More power to your Channel.!!!
@MyINNOVAMotorcycling 3 жыл бұрын
It's true that all the parts was cost me too much money. If I had noticed the right problem in advance, it would have only cost the price of a O-Ring. The leak appeared only in the left fork from the upper O-Ring. Look here (Left is Black Oiled): 0:51 the O-Ring here (Screen #2): 8:18
@gurglejug627 2 жыл бұрын
Hi matey, a number of people want to make DIY high pressure compressors (4000psi/200 bar) for refilling paintball guns- People are discussing the idea of using motorbike forks to do it - they look meaty enough. Do you know what pressures they are designed to handle? And do you have any suggestions or interest in looking into it... it would be a very popular video I reckon. I might try myself, but need to know the pressure tolerances of forks, plus I don't have a lathe and am worried about getting stuck 99% of the way through the process. With a proper air filter/dryer these could be used to fill diving bottle, too (reserve air source for filling paintball guns). Any help or ideas gratefully received!
@kan815k 4 жыл бұрын
Hi Great video and detailed. I have keeway f-act evo 2012 model and looks exactly the same shocks. Can we have the link where you bought the seals from? Thanks
@MyINNOVAMotorcycling 4 жыл бұрын
Hello and thank you very much for your compliments. I don't know what to say about if it is the same part as my Innova. Google according to its part name and Keeway catalog number and find the deal that suits you the best.
@jm1329 5 жыл бұрын
Muy buen video lastima que no esplica en español
@MyINNOVAMotorcycling 5 жыл бұрын
Hice las explicaciones del video en un idioma internacional. ¿Hay algún segundo en el que la explicación de un detalle en el video no sea clara para usted?
@constantineaeson3686 6 жыл бұрын
Excellent video. But I have a question , changing oil on my forks I've notice that the left fork spring is smaller than the right one . Is that normal or is time to replace it? Or put a spacer?
@MyINNOVAMotorcycling 6 жыл бұрын
I did not check if there was a gap between the two lengths of springs, I only checked that they separately meet the specification. A spacer with soft or weak steel will cause damage. I would not insert a spacer. What lengths did you measure? Because in any case a difference of one millimeter would make no difference. I have also shown that when you start ordering a few parts, it comes out more expensive than purchasing the whole fork, so you have to pay attention to that as well.
@constantineaeson3686 6 жыл бұрын
tamirkr thanks for the quick response. The difference is 2 cm.
@MyINNOVAMotorcycling 6 жыл бұрын
Thanks, but I would not rely on my quick response, I'm usually slow, and sometimes it can take a weeks. Two centimeters is a strange and unlikely gap. Maybe you got two springs from different models? One before 2007 and the other after 2007, because according to the Hynes Guide, this is the gap between them, two centimeters. kzfaq.info/get/bejne/h55hh8Z6y7C1j2Q.html
@constantineaeson3686 6 жыл бұрын
Very impressed...! That's the case and that explains it all. Bought this bike last year second hand, from the very first look I've noticed the front fender was from wave (the bike is innova) possibly they have had a small crush and replaced the fender and one fork. Tamir thanks again and keep up the good work..!!!
@leobro2018 11 ай бұрын
wow great video! thanks dude! Do you think your instruction video can be applied to Honda super cub 110 (dream cub) samely?
@MyINNOVAMotorcycling 11 ай бұрын
Hi. If the structure is the same, then the answer is yes. You can check it in the parts diagram of your model.
@mantukumar4705 5 жыл бұрын
Agar front socker ke pipe ka paint kharab ho jaye to kaise solve krenge
@benialpianto5315 5 жыл бұрын
Ganti oli sobreker depan
@sopheapan8773 4 жыл бұрын
Hello bro..nice video i would like to ask you please my Honda wave- 110cc How much ml oil each fork? Thanks u
@MyINNOVAMotorcycling 4 жыл бұрын
I do not know. Try to see if the parts are with the same catalog numbers. If this is just a difference in volume engine then there should be no difference. But I really don't know.
@tomysanchez5522 5 жыл бұрын
Con el mismo rresorte kitaste lo de abajo para k no diera vuelta
@stefanmelo 3 жыл бұрын
Whats the thing with this 4 split cameras videos!?, how are those suposed to be watch?
@MyINNOVAMotorcycling 3 жыл бұрын
I provided a lot of information in this video, and edited it as one relatively short video. You can welcome to focus on what is important for you. Overall the close-up shots are very clear even when the screen is split. I gave numbers to the split screens(1 to 4) in the order of work. The video is built as a fast clip, in the KZfaq toolbar there is an option to reduce speed to 0.25.
@omarothman3804 4 жыл бұрын
I have another option of servicing the fork. 1. Go to any service centre 2. Done
@MyINNOVAMotorcycling 4 жыл бұрын
You missed the whole point? The video channel came to amuse you, show you how a garage works, teach beginner mechanic the profession, and help DIY enthusiasts who make the repair as a hobby. Hobby as you known need time and money.
@newtalent4273 4 жыл бұрын
@@MyINNOVAMotorcycling 100% true bro, 👍
@AMXM-do5kw 4 жыл бұрын
Any service centre must have this knowledge to begin with. Great video.
@slh0077 2 жыл бұрын
Hello sir, my lower damper bolt just spinning, I cannot get the bolt out. What should I do?
@MyINNOVAMotorcycling 2 жыл бұрын
4:06 You need to put the spring and the spacer back in place, close the fork from the top, then push the piston inward. The force applied on the damper in such a position should stop the rotation of the damper and allow you to open the screw. Maybe you will need the help of another person to hold the piston pressed.
@slh0077 2 жыл бұрын
@@MyINNOVAMotorcycling Does it need to push hard?
@MyINNOVAMotorcycling 2 жыл бұрын
@@slh0077 Hard as shown in 4:06 it should work. The spring is very strong and you most to be careful, it can be really dangerous!!! You may get an another person to help you, and if not go ask for the help from professional mechanic in your area.
@slh0077 2 жыл бұрын
@@MyINNOVAMotorcycling thanks sir
@faizkhanm242 5 жыл бұрын
Aap ne. 8 ki t me bering fit ye ek naya karnama hai
@maricelsiccuan3244 5 жыл бұрын
Pwedi po ba ako mag training sa inyo
@dimasreza2711 5 жыл бұрын
Can you share manual book link download?
@MyINNOVAMotorcycling 5 жыл бұрын
These are the sources I know from the Internet (These are not my publications): docs.google.com/file/d/0BwmYWlzMWkPhemxqcHUtRXA4Yk0/edit?pli=1 docs.google.com/file/d/0B6EDVo72Y5BfNjIwYTFkNWYtODZhMS00MTYyLWFmYjYtNDFhYTYyMjEwZmEx/edit?pli=1 I also recommend HAYNES guide, worth every penny: www.amazon.co.uk/ANF125-Innova-Service-Repair-Manual/dp/1844259269/ref=sr_1_1?s=books&ie=UTF8&qid=1330845803&sr=1-1
@romanosstroggilis9970 4 жыл бұрын
Are you sure the 4 bolts that hold the 2 suspensions need 64nM?
@MyINNOVAMotorcycling 4 жыл бұрын
Yap
@romanosstroggilis9970 4 жыл бұрын
@@MyINNOVAMotorcycling Oke!
@ganeshsawale9395 5 жыл бұрын
Aap sangit ke jagah bataya kare please
@MyINNOVAMotorcycling 5 жыл бұрын
The music is taken from KZfaq's free audio library kzfaq.info/get/bejne/h55hh8Z6y7C1j2Q.html kzfaq.infomusic
@tongchidiymotofix2716 5 жыл бұрын
do you mean its better to buy new fork assembly for only 90$ rather than to repair your old one because it much cheaper and most of all its brand new.
@MyINNOVAMotorcycling 5 жыл бұрын
I'm not trying to say anything, I'm just sharing. My films are not a course in mechanics. Besides, the new pair costs 56$, my patch cost 90$. I'm talking about the cost of the parts and materials, in the garage you will also pay for the wages of the mechanic's work. The total expenses, and as an amateur mechanic, the repair cost me about 90$, while a new pair of forks costs about 56$. You can also see this as a kind of self-humor. In retrospect, it seems that only the replacement of the upper seal was sufficient. That O-Ring cost only 2.9$
@tongchidiymotofix2716 5 жыл бұрын
@@MyINNOVAMotorcycling but I think if you have a tools already your costs my less, you only pay for seal.
@MyINNOVAMotorcycling 5 жыл бұрын
Absolutely true, but in that case(Honda INNOVA), I could not find a way to make the repair without that special tool which cost me 28$ The special tool was added to the general account. But again, it was impossible without him, so as an amateur mechanic who did not have that special tool, I added his price to the general cost.
@MyINNOVAMotorcycling 5 жыл бұрын
@Gary Dodgson Excellent thought, of course you can produce such a tool yourself, or use a Socket in a suitable diameter. Either way, the set that I bought, and made from aluminum, is cheaper than the price of professional tools. There is a unique difficulty here for this particular model, the seal is adapted to the pipe with extreme pressure. That's why you need a lot of strength And power to bring it in place. Using strong force on the delicated seal, without a special tool, will destroy the delicate springs that sit inside him. See the comment attached in the beginning of the comments area, a comment of Tyler Durden from Vietnam.
@obbysianjelele-jn5md Жыл бұрын
How many milliliters of front shock oil is required in one fork(shock) for XL125 l? Please may you help me !
@MyINNOVAMotorcycling Жыл бұрын
Every model and its specifications, I recommend the Haynes books, which year is your model? You can try to fill according to level like in Honda Innova, according to height, 8:46 then take out or add oil according to the feeling.
@Bob-pn4zx 11 күн бұрын
Hello Thank you for the video To injection is the same fork? Can i put 5w fork oil and how much ml?
@MyINNOVAMotorcycling 11 күн бұрын
Yes, the shock absorber is the same for both models, the injected one and the one with the carburetor. A less viscous oil is possible, I'm not an expert on that subject, but as far as I understand, the amount is the same amount of oil. You can also change the pair of rear shock absorbers to softer ones.
@jamescedricdavid6454 3 жыл бұрын
Do I really need to replace the small spring?
@MyINNOVAMotorcycling 3 жыл бұрын
It is mainly the replacement of the oil, and the replacement of the seals. Note, for me all the components were found to be OK, but I replaced because I had the parts to replace. In my particular case, the malfunction that caused the oil to leak was a defective O-Ring in the top Left Fork.
@fazllylee7585 4 жыл бұрын
What brand fork oil you use bro?
@MyINNOVAMotorcycling 4 жыл бұрын
RACING FORK OIL SAE 10 W MEDIUM - 500ml Fuiiy synthetic LIQUI-MOLY, Made in Germany
@juliusferguson5393 2 жыл бұрын
Is any other oil valid other fork oil that I can use?
@MyINNOVAMotorcycling 2 жыл бұрын
Yes, oil from other manufacturers, and oil more viscous like 15W(to stiffen forks), or more thinner like 5W. It must have a Fork Oil ("Fork Oil" written on it). I do not recommend deviating from the manufacturer's recommendations: Fork OIL10W
@User-R03web 2 жыл бұрын
The D.I.Y. Special tool at 04:52 you must buy it , or you can create it by your own?
@MyINNOVAMotorcycling 2 жыл бұрын
I cteate it (D.I.Y)
@Izzulsif 3 жыл бұрын
Do we really need to pump the fork when refilling it?
@MyINNOVAMotorcycling 3 жыл бұрын
Yes, it is necessary (8:35). The operation ensures that the oil penetrates all the oil passages in the shock absorber, it also ensures that the quantity measurement by height will be correct.
@Izzulsif 3 жыл бұрын
I see, thanks for the answer 😀 👍
@user-zy9fs3us3v 3 жыл бұрын
What sae? Thanks
@destramandala8902 5 жыл бұрын
kalau baut bawa sok suda rusak baut nya suda dol cara nya gimana
@MyINNOVAMotorcycling 5 жыл бұрын
If the screw is broken you must take a deep breath, you must not lose control. Look for KZfaq videos on subject: "Screw extraction" Or "How to remove a broken bolt" kzfaq.info/get/bejne/ldOEebSTxrqXipc.html Good luck
@SaapeXD 4 жыл бұрын
What is a good rear suspension for innova? Also can an aftermarket shock be installed with the chain cover?
@MyINNOVAMotorcycling 4 жыл бұрын
Thank you for the question. If the aftermarket part is the same size of course there shouldn't be a problem. If you have a doubt please ask the seller and ask him for a commitment on this issue. If you order an upgraded part it will be possible not fit, and then adjustments will be needed. Either way, only a qualified mechanic can do the job safely, so I encourage you to contact a qualified mechanic. From what I know sometimes there is an adjustments that need to be made on the plastic cover . Maybe sometimes an adjustments be necessary to the metal chain cover? The original shock absorber is relatively hard and gives more stability, and a soft one giving more comfortebl riding. In countries where there are leagues of sports competition, there are also a number of other upgrades. KZfaq has begun to block iterant links to stores, but you can share knowledge and tell us what brand and model you are debating about? what the name of the store you are going to purchase from? at what price? thank you very much.
@SaapeXD 4 жыл бұрын
@@MyINNOVAMotorcycling Thanks. I am a mechanic. But i do not work on motorcycle but large diesel engines and generators in a powerhouse (small ones are 1 MW , large ones 9MW gensets) Recently i purchased a motorcycle and i want to do maintenance works myself as the garages are very expensive and they cheat a lot. Honda innova / wave series is very fuel economic, thats why i bought it. I am yet to learn the maintenance works of small gasoline engines. Its pretty much similar to big engines. Infact even easier as its only having one cylinder unlike twenty or 16 cylinders in the engines i am working on. The default rear suspension is a little hard for me and for many passengers hence i was thinking of buying an aftermarket shock with the oil reservoir. Do you recommend?
@MyINNOVAMotorcycling 4 жыл бұрын
@@SaapeXD I am not a certified professional mechanic, I am a very high level non-qualified mechanic because I did not did state certification exams. Either way, mechanics are very nice people, in every profession there are unfair people, I don't get a sweeping statement blaming mechanics for "they cheat a lot". If you also have a good mechanic hands, and you have the tools, that's another matter.A self-repair(DIY) is very enjoyble and thar has advantages, for example: you don't have to waste a time for accessing the garage. And yes, engines no matter the size, built from similar assemblies, this small volume engine means less screws, less weight, less special tools, and therefore easier to maintain. I had a successful experience with the absorber of the Greek CUB model 2011(Nipponia) , yes, there are absorbers that are more comfortable, and as I wrote may require cutting in the plastic cover for adjustments.
@SaapeXD 4 жыл бұрын
@@MyINNOVAMotorcycling What about this one: bikerzbits.co.th/honda-wave125i-g-series-yss-shock-absorbers-rc302-340t-55-gold.html The picture is exactly my bike. But it does not have the Chain Cover with the shock absorber installed.
@MyINNOVAMotorcycling 4 жыл бұрын
The link doesn't work, assuming I watched the one you mean.....YSS All New Gold Series G-Series RC302-340T....It's a shock absorber for racing. It is very expensive ,relative to the standard. It can be ordered tuned according to your weight. And of course, its wide structure in the upper area(the nitrogen gas tank) probably requires a change in the rear plastic cover of the motorcycle. It seems unnecessary to me, you claimed that you are with a scooter to save costs. On the other hand, it's a quality shock absorber, only you know what's good for you.
@jamescedricdavid6454 3 жыл бұрын
When doing this, do I really need to replace the inner ring and the small spring?
@MyINNOVAMotorcycling 3 жыл бұрын
If there is abrasion or wear then you need to replace. Sometimes it will be cheaper and of course also requires less work, to buying a new set of shock-absorbers(Forks). Try to check the cost of parts versus purchasing a complete set of a new shock-absorbers(FORKS).
@jamescedricdavid6454 3 жыл бұрын
I also changed the parts that you changed, by problem now is how much fork oil do I need to put?
@MyINNOVAMotorcycling 3 жыл бұрын
There are two measurement methods, by quantity(70.5-72.5ml) or by height(76mm), see the attached link, in the split screen at the top left. kzfaq.info/get/bejne/h55hh8Z6y7C1j2Q.html
@jamescedricdavid6454 3 жыл бұрын
@@MyINNOVAMotorcycling What's the best method? I measured the available fork travel and it showed 84 mm and I also learned that I should leave a clearance of 5 mm so that I get a 79 mm fork travel. Will the oil height method achieve this?
@MyINNOVAMotorcycling 3 жыл бұрын
I do not know the numbers 84mm or a clearance of 5mm. I know what I wrote down for you earlier. The two methods I have listed are equally good. The two methods I presented work when the spring is inside, and the tube is inserted all the way into the cylinder.
@pablob6520 4 жыл бұрын
What's that guitar into off of? I need to know 😬
@MyINNOVAMotorcycling 4 жыл бұрын
I didn't understand. Give me a minute on the timeline. I would happy to reply if you will giving me a chance to understand your question.😬
@pablob6520 4 жыл бұрын
@@MyINNOVAMotorcycling ahh no worries. Turns out it's produced by KZfaq, not an actual band. Thanks anyway
@gehleeace 5 жыл бұрын
How much one Honda fork of 125
@MyINNOVAMotorcycling 5 жыл бұрын
The shock absorber is not completely symmetrical. There is the right side, and there is the left side. Some parts are the same, and some do not. For price reference (pair) looked here: kzfaq.info/get/bejne/h55hh8Z6y7C1j2Q.html
@chrislabago5426 4 жыл бұрын
This video has more edits than the avengers end game and harry potter combined 😒
@MyINNOVAMotorcycling 4 жыл бұрын
You're right. There is so much to explain. I edit the material in a quick clip style. Anyone who wants to explore the details go to the KZfaq toolbar and lowers the speed to 0.25.
@kheintech 3 жыл бұрын
Savage 😅
@sridharnalli3206 4 жыл бұрын
Xtreme bike 150cc fork me kithna ml oil dalna cha he a
@MyINNOVAMotorcycling 4 жыл бұрын
I do not know the manufacturer's recommendations for your model. More oil will give you a shock absorber with more rigidity, less oil (more air) will give you a softer shock absorber. The main thing is that on both sides you put the same amount of oil.
@sridharnalli3206 4 жыл бұрын
How much oil both fork in Xtreme sport bike 150cc
@MyINNOVAMotorcycling 4 жыл бұрын
I guess less than the contents of one 500ml bottle. Only GUESS
@eddiemaranan6790 5 жыл бұрын
hi I dnt see how many ml the oil? pls
@MyINNOVAMotorcycling 5 жыл бұрын
In the upper screen on the left kzfaq.info/get/bejne/h55hh8Z6y7C1j2Q.html 70.5ml to 72.5ml
@elmerindig7280 5 жыл бұрын
@@MyINNOVAMotorcycling 70.5 - 72.5ml oil each fork?
@MyINNOVAMotorcycling 5 жыл бұрын
@@elmerindig7280 Yes 70.5ml to 72.5ml oil each fork.
@pp-si2dm 5 ай бұрын
This job isn’t for the faint hearted! 😂 Seriously guys, even if you have the knowhow, it’s is seriously tricky requiring professional tools. The time it took me outweighed the reward of doing it myself. Never again. Will be going to garage next time! So please THINK before even attempting this job.
@MyINNOVAMotorcycling 5 ай бұрын
Sir thank you for sharing. Yes, this is a job that requires a relatively high skills. I failed the first time. The idea in DIY is not to save money, it's the enjoyment of the hobby. You pay money for hobbies, in this case the money for learning from your mistakes, or the money for special tools and so on. Do-it-yourself mechanics is a nice hobby, not the cheapest hobby, there are cheaper hobbies than that. Those who do not have time, or those who do not have the patience for this hobby, the cheapest for them is to go to a qualified mechanic that they trust on. In the case of the Innova front forks, sometimes it is cheaper to buy new ones than to repair the used ones, and then the whole job of replacing them is much less challenging, and a lot easier.
@PavanKumarHB 5 жыл бұрын
When it needed?
@MyINNOVAMotorcycling 5 жыл бұрын
According to the manufacturer's instructions, it is recommended to replace fork oil every two years (Hopefully I am not mistaken about time). If you will decide to change oil, you will need to replace all the seals. In my case, I opend the fork because there was an oil breakout from one of the seals (the O RING at the top edge). When there is an oil leak, dirt will be stucking on the shock absorber, and you can also see signs of oil moisture. When the oil begins to come out, the fork stops functioning, and what you feel is only the strong vibrations of the spring, in such a situation it is very dangerous to ride.
@PavanKumarHB 5 жыл бұрын
@@MyINNOVAMotorcycling so, in my case . My bike working fine from 2 years(new ) so no leakage, so not required so early!!
@MyINNOVAMotorcycling 5 жыл бұрын
Yes
@christianstevejuliada9522 2 жыл бұрын
Where i can find the parts catalogue of the motorcyle?
@MyINNOVAMotorcycling 2 жыл бұрын
search in Google "Honda ANF 125 parts catalog PDF" And also in the online stores selling spare parts you will find there a full catalog pages
@seramafika4589 5 жыл бұрын
Where you from bro?
@MyINNOVAMotorcycling 5 жыл бұрын
ISRAEL
@marvinloka1246 5 жыл бұрын
Hello How much oil to put in it?
@MyINNOVAMotorcycling 5 жыл бұрын
70.5ml to 72.5ml oil each fork. See Split screen(1), in the upper left corner of the full screen: kzfaq.info/get/bejne/h55hh8Z6y7C1j2Q.html
@marvinloka1246 5 жыл бұрын
@@MyINNOVAMotorcycling thank you very much for the answer.
@olympiojr.belesario4563 3 жыл бұрын
What is the size of the oil seal?
@MyINNOVAMotorcycling 3 жыл бұрын
I only know the catalog number as mentioned in the video
@rfakn5582 5 жыл бұрын
😳
@jhomotovlog3874 Жыл бұрын
Ano po gagawain pag malambot pag sakay palang bumabaon na
@MyINNOVAMotorcycling Жыл бұрын
If the shock absorber is soft because the oil has escaped, then you need to replace the seals and put in a new fork oil. The shock absorber can also be stiffened by putting in thicker fork oil (depending on what you have now). I put in 10W fork oil, and I think there is also 15W and 20W. Other methods: insert a stronger spring, or insert a longer spacer (which will make the existing spring to be harder).
@firdausarrahman4798 4 жыл бұрын
What is 64Nm ???
@MyINNOVAMotorcycling 4 жыл бұрын
64 Newton meters is a torque. Torque is a rotary force, in this case 64 Newton = 64kg force, acting on an arm of one meter from the point of rotation. Newton includes the Earth's gravity.
@argietorregosa3481 3 жыл бұрын
Pwede ba tangalin ko yung spescer nang shock ko sa frontshock may may spescer kasi
@MyINNOVAMotorcycling 3 жыл бұрын
Sorry, I'm not sure I was able to understand your question, it is possible to make changes and upgrades, I do not recommend it at all, it can reduce safety and may cause an accident.
@Mla7e 3 жыл бұрын
How much oil is for one
@MyINNOVAMotorcycling 3 жыл бұрын
Please observe at 8:17 In the screen (1), the top left screen. 70.5 to 72.5 ml. Another method: when measuring the level 8:42 Screen (1), the height measured is 76 millimeters (without the spring, when the inner tube is inserted all the way in).
@mogias7 3 жыл бұрын
9:00 1window with the spring how mm?
@MyINNOVAMotorcycling 3 жыл бұрын
Go for the first method 8:18, by volume, it can be measured with a large syringe. the syringe costs pennies (At pharm shops).
@shahfri 3 жыл бұрын
What song?
@MyINNOVAMotorcycling 3 жыл бұрын
see at 9:51
@hayriAkbyk 5 жыл бұрын
Yenisinin fiyatını görünce, verdiği emeğe acıdım.
@MyINNOVAMotorcycling 5 жыл бұрын
Bu komik bir video. Gülmen gerekiyordu. Rehberlerimde mizah buluyorsun. Bana acıma? gereksizdir. [Google Translate]
@hayriAkbyk 5 жыл бұрын
My INNOVA Motorcycling pekâlâ 🤣
@MyINNOVAMotorcycling 5 жыл бұрын
Tabii ki sorun yok🤣 Bazen sadece O-Ring in değiştirilmesi gerektiğini unutmayın. 2.9 $ Parça Numarası 91304-MJ0-003
@User-R03web 2 жыл бұрын
The genuine fork set is very expensive, it costs around 140 euros
@MyINNOVAMotorcycling 2 жыл бұрын
Yes 9:22
@mogias7 2 жыл бұрын
8:23 4window 303.1 is to short..maybe is 330.1mm or 333.1 mm ?
@MyINNOVAMotorcycling 2 жыл бұрын
Hi. At your request I have checked again, these are the minimum dimensions that appear in Haynes Guide No. 4926 on page 5 * 1 I do not know if the measurements are too short, I know that these are the minimum measurements according to Haynes' guide, less than that, according to the guide., the spring needs to be replaced. (303.1 mm MIN is ONLY for models 2003-2006)
@mogias7 2 жыл бұрын
@@MyINNOVAMotorcycling i have 2003 model....my spring is 330.1mm and has softened a lot so that it has sat down and hit the puddles
@MyINNOVAMotorcycling 2 жыл бұрын
@@mogias7 The standard size for the 2003 models is 316.3 cm, at least according to the Haynes guide, so I think you are holding the wrong spring. On the other hand, according to the same guide the standard for the 2007 model is 328.8 cm, and I measure 350 cm (time 8:23) , so I do not know how much we can trust that data in the guide. It happens, not much, even rare, but it happens that in books, even technical books of the manufacturers themselves, you will find mistakes. Bottom line, it's possible that (1) your spring did not fit your model, (2) old weakened spring , or (3) maybe you forgot to put one of the spacers? Or other assembly malfunction?
@dimisdnc710 2 жыл бұрын
In how many kilometers this work happens ? By the way, nice pajamas 😎😎😎
@MyINNOVAMotorcycling 2 жыл бұрын
31,170Km I was not careful about riding on bumpy roads, or getting on sidewalks. Now I'm more careful. Other commenter here suggested that the problem is with the assembling in the Honda factory: The gripper nuts on the handlebars were tightened too tight and therefore thay destroyed the top O-Ring.
@lambrostsalis Жыл бұрын
I have 102.000 km on my innova 125i and all parts are working perfectly.
@dimisdnc710 Жыл бұрын
@@lambrostsalis έχω κάνει την διαδικασία στα 20.000 χιλιόμετρα μόνο! Γιατί το μηχανάκι δεν είχε καθόλου ανάρτηση! Κοπανουσε σαν παλαβό. Οπότε σου συστήνω να το κάνεις κι εσύ και θα καταλάβεις την διαφορά.
@lambrostsalis Жыл бұрын
@@dimisdnc710 Λογικά θα γίνει λειαν συντόμως γιατί είδα λαδάκι που έτρεξε στις πίσω, οπότε θα θέλουν και οι μπροστά φτιάξιμο
@devilalrawat62.devilalrawa28 5 жыл бұрын
Devi lal reset
@mohamadazlan7771 3 жыл бұрын
Serabut..
@corneilcorneil Жыл бұрын
No "special tool" needed, just use a socket
@MyINNOVAMotorcycling Жыл бұрын
Hi, Thank you for your advice👍👍 What socket did I use (what is the size of the wrench, and what his outer diameter? And with what technique did you pull the old seals out of their place? 4:52
@user-df1qr2fe4g 4 жыл бұрын
7:55 (3) What is it?
@MyINNOVAMotorcycling 4 жыл бұрын
The Four initial assembly steps in order from 1 to 4, on one split screen.
@MrWebuser 3 жыл бұрын
en.wikipedia.org/wiki/Thread-locking_fluid
@vergeltuble5497 Жыл бұрын
😯😯
@jeromesalazar3744 4 жыл бұрын
not complete, coz without info about oil, to how many,.
@MyINNOVAMotorcycling 4 жыл бұрын
The information you request exists in the video. Look again at step 10. On the split screen you will look at screen (1), this is the screen in the upper right corner. There are two methods of measuring the amount of oil, one of which is 70.5-72.5 ml. kzfaq.info/get/bejne/h55hh8Z6y7C1j2Q.html
@marcellovecchiarelli3774 4 жыл бұрын
il video sarebbe anche molto ben fatto solo che la visione a 4 immagini video accellerate ti fa uscire di testa e nonsi capisce niente.
@MyINNOVAMotorcycling 4 жыл бұрын
Grazie per la recensione Non volevo fare un video di un'ora intera. Nello stile che fotografo, senza editing, diventerà noioso e poco interessante. Alcune persone guardano le mie clip con piacere. Alcuni stanno guardando per imparare. Puoi interrompere il video nel punto che ti interessa di più. Puoi anche rallentare la velocità del video a 0,25 modificando le impostazioni di KZfaq Player. Per i film in tempo reale hai altri canali. Mi piacerebbe vederti di nuovo qui.
@saintstv2224 5 жыл бұрын
Not clear... Its to fast
@MyINNOVAMotorcycling 5 жыл бұрын
It's fast because it's a video clip. You can slower the speed to 0.25. Click the Settings button, click Change Speed, and select a slower speed.
@dianecovena6319 5 жыл бұрын
h
@rachelguzman8812 3 жыл бұрын
nice tutorial 👍 idol keep it up please visit channel - THE EXPLORER FOR ALL 1. paano mag repair ng starter relay bubuksan natin 2. paano mag repair ng fuel gauge napundi sa gas 3. paano gumawa ng tester light for continuity 4. paano mag tune up
@miltonanding213 3 жыл бұрын
.
@joeycottontail943 Жыл бұрын
Horrible way to do this. Get insurance and leave parked on street. Gets stolen immediately and get fresh new scooter. How it’s done here.
My INNOVA Motorcycling
Рет қаралды 97 М.
MOTO MENTOR
Рет қаралды 65 М.
My INNOVA Motorcycling
Рет қаралды 7 М.
Thoy Chomnan
Рет қаралды 11 МЛН