KZfaq is only good for searching up how to learn things other than that it's full of nothing...But gems like this is why I still am on here. This is one of those teach a man to fish things and I appreciate you for it 🙏🏾

U saved me, Belt was the problem but now it’s working, Thank you!

A bad drain pump or clogged filter can also cause the drum not to spin .. and it's a very common issues as well .. should've been added to the 5 top ... the controller would be the last point to check .

I should start making repair videos. As a technician the main cause I see on stator motor style, is Bad SPEED SENSOR. Which is attached to the stator. It’s a 10-15$ part.

cant believe it changed switch and it works like new thanks

So nothing on KZfaq worked, so I did my own analysis. Looking at the board there were some dirty parts on the components traces. After cleaning it with robbing alcohol. It looked like one of the traces leads were rotten off maybe because of moisture or dust. I used my phone camera to zoom in 10x times it's a realme xt phone. I saw that it's indeed disconnected so I took a small flexible wire. Used fine sand paper on it so the solder would stick to it easily. I also used the sand paper to expose the leads on the circuit board. After cleaning it with alcohol I soldered the wire to the board to make the jumper. I also noticed some of the components in the same area looked worn. So I took the heat gun put some soldering paste on the components. And covered any vulnerable plastic components with aluminium foil to help it not get burnt. After I use the heat gun to heat up the components, reflowing them it looked brand new. Plugged it in after and works perfectly.

I fucking love you!!! The belt wasn't broken , but it was just laying inside the washing machine. Don't know why , just rented this shitty whole. Thank you!!

Yesterday, my washing machine wasn't spinning to rinse. After going through all the checks, realissed knob was accidentally set to zero. May be when cleaning it. So sometimes start with settings checks. 😊

If the belt is just off the pulley, check the bolt holding on the pulley. They are well known to work loose and cause the belt to slip off.

No refunds if they tell you wrong solution. Buy parts somewhere else. I learned the hard way.

Ours is doing the same thing gets to a certain point & then will stay there for a long time.

Ge smart front load . It spins fast when it's empty . But I washed 1 Towel , and it will spin that 1 Towel but not fast . When it's " done" the towel is soaked dripping still . So it's not spinning the heavy out of it. Any thoughts?

I actually clean the filter drain the water below before I saw this video I was proud of myself I thought maybe I fix the problem but the code keeps coming up early I keep draining the water out the bottom door it just won't finish the cycle of spinning and draining and now there is a loud noise in that door area

Great video. This help me troubleshoot and repair without calling a repair man

Good 👍

Thku v.much it's working

My sharp automatic washing machine's spinning problem stop at mid cycle, it immediately proceed to washing without finishing the spinning cycle,

Needs some help here😢 my samsung washer don’t spin and stock at 9 minutes after draining. Pump motor can be heard running but the drum doesn’t spin! Any thoughts on this? TIA

My Samsung front loader washing machine stops mid way, doesn't complete the time cycle. What can you suggest sir

Great video , it helped me

I asked what to do if the Samsung washing machine doesn't spin actually this video states that what are the causes

My lg F1480YD5 wont rinse and spin

My GE front loader want start it goes directly to the last minute, it shows rinse on the screen, and the rinse doesn’t happen either and it turns off. Please help!

The number one cause is issue with a drain pump!

For me the belt had snapped and i replaced but when it spins it sounds like it dragging on something. Any advice please thanks in advance

I have a Maytag front loader washer and dryer. If I put it on the fresh rinse and spin cycle it will spin, but on all of the upper cycles on the knob it won’t spin so I don’t think it’s the belt or the motor. It must be some kind of switch?

I have a Kenmore front loader machine that keeps stopping when it gets to the spin cycle if there are more then a couple of towels in the machine. it says "ND" on the screen.... help!

I have a samsung front loader which is not rinsing after wash replaced motor and pcb control board as instructed per repair still have issues after no codes shown, any ideas.

My frond load washing machine motor while washing rotate very slowly and heating the motor within 30seconds .bare motor take 6A load of spec. washing 93v 60w 580Rpm. what could be reason

my kenmore front load washer gets to the 6th minute then wont finish washing it will will stay on 6 minutes for like 5-10 minutes then finish but will not go into its final stage where it washes rapidly?

Hello I changed the roper lid lock and Shift Actuator. The lid lock still flash and washer still wont spin, HELP PLEASE.

My automatic washing machine Samsung front loader model number wf 7600nas does not whant to spin

Had to stand on Samsung front loader drum (210 lbs) several times when fixing constant incoming water while unplugged. Now tub is not aligned with front door seal. Any suggestions?

It indicates. DC mean what reason

I have a Kenmore elite front load washing machine, when I try to wash it on Express Wash the washer stops and I get in 02 f code on the display and it doesn't spin

I have a samsung crysral washing machine serial no: 06SU53AG900047F. I replaced the inverter checked the belt filter is clean the drum turns left and right but it will not spin it stops at 9. Is there something else to check? Will appreciate if you can help

hi can u please help me, I have a indisit washing machine and the drum doesn't turn at all but the belt and everything work on the rear. Just the drum doesn't move from the front. What do u think is wrong

I have a ge front loader and it wont spin properly. Spin once, stop, spin than stop spinning

kenmore front load washer serial # XC32716687 will not go into high spin , it will drain and slow spin though

My washer does spin but not finish the cycle. We have to start the rinse and spin cycle. Please help

I have a Samsung front load washer giving code 4E(water supply) I have tried a new water pressure sensor, my husband put in a new MCB. The water supply inlets have been changed. Samsung is the worst for repairs abd too many hoops to jump thru. Sears repair guy changed time twice in the same day, didn't come. It fills with water, then drains flashes code 4E but don't trigger to spin. My filter is clean.

Number 1 Brushes?

why my washing machine does not spin Samsung P1453GW/XEE

Samsung front load power on and off problem?

fix it

This is great, but my anxiety went off the roof watching this video I’m too paranoid to even attempt this 😫

My bosch washing machine not start it's automatically water coming out through exit hose

I give you more interesting puzzle: In wash mode device rounds the drum. After 1 min drum stop rounding and just shakes by motor. Load of machine is low. What it can be? BTW in "rinse and spin" mode drum again works as it should!

How about turning off the bell!

My Hotpoint front load washing machine's belt slips regularly when machine start spining and drum stop working. Belt change works for some time but again it slips.Can someone give suggestions. Thanks.

Logik won't spin take water front load washer machine

Why is my samsung washing machine spinning the screen goose off

Ifb spin not working

Bought a belt, remove the back ,the belt is n it's place...washer Not spinning or even agitate,will get to o1 on timer & just keep running Will not stop. timer dose not move after after O1.juzt keep on running,unt I manually turn Off.Please Help!!!!

Could the control panel be faulty ?

Can i share a video??? It tries to spin..but doesnt

Mine will drain, but *usually* not spin. Rarely, it does, and it seems to do so reliably if it is empty. It is a direct drive model. I have replaced the drain pump and the door lock assembly. I have made sure the drain line is free. I'm honestly out of ideas. :-(

Ok so I can't unlock the door it's jammed or something

Maytage model number MFW9700sQ1 trouble code FO7

Sometimes it will agitate or spin slow with a damaged stator and rotor

ooooo...

The washer I have sucks I hate it

I have replaced the door lock but it still it will not spin with clothes in it. It worked when I just turn on drain and spin after replacing the door lock.

Gfwh2405l0mv GE washer machine doesn't spin

whirlpool sensation EX it spins clock wise ,after sometime time goes on but wont spin more.if i press pause button then reapeat it motor spins agin and stops again.any idea any body cud help.thankin you.☺

Too many problems just buy a second hand one

The washing machine is a washing machine, but not spinning?

Xqg80-q814de

Totally irrelevant 😞😞

Not impressed. His first solution is the belt. But if the machine has been washing rotating the machine back and forth, then the belt isn't broken! Unless it happened to break at some point in the wash cycle. I'd prefer a more step-by-step approach, and start with the most common reason, working on from there. Diagnose, don't just chuck out random answers.

🦧👍

My front load washer isn't spinning correctly. It will spin just never spins fast. It will spin slowly or even stop. It will stop and change directions, but never spins fast enough to pull water off close.