@elboa8 9 жыл бұрын
One to build, for sure. Thanks Peter.
@mortenrolsing7137 9 жыл бұрын
Realy love your videos, Thanks. I am realy learning a lot. Greatings from Denmark
@TheBreadboardca 9 жыл бұрын
Here is a post on Element 14 where I have the schematic posted and the STL files for the front panel I created www.element14.com/community/groups/test-and-measurement/blog/2015/07/31/complete-analogue-dc-load-0-5a-0--60v-but-not-300w
@necbd8893 Жыл бұрын
Great job 👏
@milanmladenovic 9 жыл бұрын
Great video. Thanks
@gnomishworks 7 жыл бұрын
Great job on the DC load. A bit long a parts, but well done. Question on the voltage reference. Would it help the Mosfet drive if you used a 10v reference instead of 5v and amplified the arbitrary waveform input by 2. It seems everything else is 10v capable. I have a couple of LT1236AIS8-10 references and wondered if that would work/help. Thanks
@TheBreadboardca 7 жыл бұрын
It is all 10V compatible so it would not harm. and yes, if you up the reference to 10V you will need to either adjust the ARB input to match or divide it a little differently to compensate. either way will work
@jurgenollig6196 9 жыл бұрын
Many thanks also for that, I am learning a lot too.
@hankus253 9 жыл бұрын
Wish some of the items you were pointing out were in view of the camera.
@felixcat4346 7 жыл бұрын
Nice vid, but it would have been better to not compartmentalize the theory using the function gen utilization and the trimmer pot. Not obvious to the uninitiated what the benefit of introduction of wave forms in a device like a dummy load is useful for.
@suzaneouroumis8150 7 жыл бұрын
Hi Peter, I believe there is a weak link in the DC load circuit. I build one and it was working fine. For some unknown reason the DC load mosfet shorted inside - while checking the mosfet offline - i found its showing continuity between drain and source. After replacing the mosfet the DC load was not working- i found the opamp is heating - replaced opamp and its working now. Do you think the gate should be driven through an optocoupler ?
@TheBreadboardca 7 жыл бұрын
It should not be necessary, I have seen many similar designs and they all drive the FET directly., an opto would only be needed if there is a significant difference between the source voltage and the op-amp output range that would take it out of its operating range or common mode voltage. I have used mine several times with no issues. If you have further information regarding the scenario that caused the failure i would love to hear it.
@thecombatengineer7069 5 жыл бұрын
DC load BOM : $50, Agilent 33622A $3900. For just $3950 you could have your own!
@TheBreadboardca 5 жыл бұрын
Actually the 33622A is about 8000CDN ++ as it also has all the options, Memory, GPIB, BenchVue etc. But more seriously, if I had a really low cost wave gen with as good a rise time at the time I would have used it as the source, the point there was to have an excelent input rise time in order to minimize its effect from the final measured rise times. When your measuring or characterizing something you should try to have measurements and source signals at least 10 times the resolution, im pretty sure I exceeded that lol.
@elboa8 9 жыл бұрын
Final circuit please, Peter!
@TheBreadboardca 9 жыл бұрын
elboa8 www.element14.com/community/groups/test-and-measurement/blog/2015/07/31/complete-analogue-dc-load-0-5a-0--60v-but-not-300w
@elboa8 9 жыл бұрын
Peter Oakes Thanks...
Family Games Media
Рет қаралды 30 МЛН
DroneBot Workshop
Рет қаралды 1 МЛН
Scullcom Hobby Electronics
Рет қаралды 106 М.