Watch Robs 5 part Drawer Making Series, #1 is here: kzfaq.info/get/bejne/pLiHgtecnt-xcn0.html
@curtdrahn85222 жыл бұрын
I make hundreds of dividers and find a few practices that make it a lot easier. The depth of cut does not need to be exact half and half, it be slightly more, it will not be seen. If you use masking tape to gang the length parts together and cut the joint they will be the same. Do the same for the other width parts. My dividers are the thickness of the blade cut and it does not matter if you use a regular saw blade and the little "ears" are hidden. The same truth will be for your example. You make it a lot harder than it needs to be. The one thing is to make sure all the parts are the same thickness. Great show.
@TheMrPastry15 күн бұрын
Really appreciate the precision and attention to detail.
@Borescoped3 жыл бұрын
Watching Rob think and work, while I’m working on flattening chisel backs on a 1K Trend. Peaceful.
@RobCosmanWoodworking3 жыл бұрын
Ah the joy of flatten chisel backs!
@joellefougere13223 жыл бұрын
Rob, you’re simply the best! Thanks for doing what you do.
@GraemePayne1967Marine3 жыл бұрын
Learned a new measurement unit today! The thickness of a shaving! 👍👍
@RobCosmanWoodworking3 жыл бұрын
Of course .....its a tried and true standard!!!!!!!
@markturbitt88073 жыл бұрын
Great instruction Rob. The attention to detail in a relaxed pace makes the entire lesson memorable. Learned a great deal on a project I would normally fly through. I become a better woodworker each time I watch. Thankyou
@RobCosmanWoodworking3 жыл бұрын
Wow....Thanks so much and thanks for commenting
@dougjunebennett99623 жыл бұрын
One fun thing to do while watching Rob's videos is to try and count the times Rob says "and then we'll go in..." or "and then we'll come in..." . What is the difference between going in and coming in? We'll never know. I'm just kidding around of course. I've learned so much from your videos Rob, thank you for all that you do for the woodworking community!
@RobCosmanWoodworking3 жыл бұрын
The difference betwen going in and coming in is where you start from....isnt it obvious????? 😀
@QuadDoc3 жыл бұрын
It so awesome watching you work! It’s so motivational and gets me pumped up to get out in the shop and get to work!! 👏🏼👍🏼👊🏼
@RobCosmanWoodworking3 жыл бұрын
go make some shavings
@davedunn42853 жыл бұрын
Patients and Presision to detail definitely wins
@anthonyhennegan36762 жыл бұрын
Your videos are incredibly helpful. Thank you, Rob!
@clemensmartin38963 жыл бұрын
You could also fit the assembly using felt on the ends like a humidor divider.
@RobCosmanWoodworking3 жыл бұрын
I have never tried that, have you?
@clemensmartin38963 жыл бұрын
Yes, when I made a desktop humidor. It’s pretty standard for a humidor divider
@NBCRGraphicDesign3 жыл бұрын
Cigarette paper (rolling paper) is generally .001" in thickness and many old time pattern makers and machinists would use it as a quick & dirty gauge for spacing items. Many tool chests get discovered with a few packs of papers tucked into the drawers-- sometimes people wonder if grandpop was a "stoner" because of the rolling paper-- Nope... He was just accurate and efficient, too. Good video. Kosman Komiko!
@patfinnerty11153 жыл бұрын
I believe in the US it is called dumpster diving the Submarines were being decommissioned at Garden Island Naval Dockyard. The Joiners and the Shipwrights wanted to make it into tables for the yard but were told by the managers to cut it into small sections and put it in the bin. Some went into the bin but a large part of it disappeared. One young joiner (3rd generation) made some beautiful furniture from it and kept the numbers that were brandied onto the boards but not on the face side. I believe the wood I had came from the Ovens each of the Subs were named after a river in Britain. It makes me sick to see someone waste something rather than let someone benefit from it and in this case our heritage would have been all the greater. Had management had the idea the Dockyard would have had some remarkable furniture Have a good day Rob and thanks for all your shows
@rwilliam01 Жыл бұрын
On a government project all the material is paid for with tax money. If you reclaim any of the material, even on a decommisioned project techinically you have to repay the taxpayers by refunding some of the money. (politician are logical aren't they)
@The_Harbinger2 жыл бұрын
Love watching the problem solving thought process, although the thickness of a shaving measurement is only something a few could reliably use. lol
@maxkaiser93163 жыл бұрын
Thanks for all the hard work and instruction !!! I would love to know how long some of your projects take in real time sure takes me longer than 13min52sec. To make anything ha ha and your boys and crew do a amazing job filming, editing, etc. Is a ton of work Great job !!!!
@theeddorian3 жыл бұрын
I have a saddle square that I use for transferring lines around edges and faces. The fun part is that the square is a test join for that exact joint I built a torsion box trap door for the cellar, joined the interior skeleton that way. The practice piece has always remained dead square so it's perfect for transfers. It is in the form of a white pine, equal armed cross, 6 inches square.
@RobCosmanWoodworking3 жыл бұрын
Thats a great way to do it
@TheSMEAC3 жыл бұрын
‘Cosman Kumiko’ 👍
@RobCosmanWoodworking3 жыл бұрын
Thats funny!! Oh-rah
@kiwdwks3 жыл бұрын
Your videos are a must see! Thanks!
@Lapsin1212 жыл бұрын
I've recently learned the drill bit technique to make the perfect slots for the dividers. Set the stop to the outside edge, than use a drill bit the same size as blade kerf to offset.
@joeldcanfield_spinhead3 жыл бұрын
My wife is going to start discovering dividers in every drawer in the house.
@robertbamford82663 жыл бұрын
“It’s just shop furniture.” Ha ha ha! Mesmerizing as always.
@RobCosmanWoodworking3 жыл бұрын
Just shop furniture!!!
@patfinnerty11153 жыл бұрын
Thanks again I have some Oregon Pine in my shop that came from the Oberon Class submarines and have been thinking of what to do with it. The planks were greased and used to slide the batteries into place.
@RobCosmanWoodworking3 жыл бұрын
Wow. Where did you get that?
@fayz44awad2 жыл бұрын
thanks , U R Great teacher
@arthurmccutchan70006 ай бұрын
Thanks
@andrewbrown81483 жыл бұрын
Great video, Rob~! I just used this technique for dividers in a shadow box. It turned out great~!
@RobCosmanWoodworking3 жыл бұрын
You should send us some pics
@robertschaeffer21963 жыл бұрын
Used spruce for drawers and dividers. Didn't realize how much spruce expands and shrinks so much in an open air shop. I make and use comb style dividers to separate rasps and files.
@RobCosmanWoodworking3 жыл бұрын
Thanks for watching and commenting
@davidpisarski56203 жыл бұрын
Fun project! I enjoy custom fitting custom dividers drawers to drawers. I have been using a CNC router to cut foam for each item. This would be a way to dress up the look with the foam in between the wood dividers. I'm going to try on my next drawer.
@RobCosmanWoodworking3 жыл бұрын
That's a great idea!
@KimbrellBrad3 жыл бұрын
What sort of foam are you using David? Not just plain foam rubber? Wouldn't think a router would cut it. Maybe some high-density stuff? Thanks in advance!
@davidpisarski56203 жыл бұрын
@@KimbrellBrad I'm using Kaizen foam I bought on sale from rockler. it is a high density foam and cuts great on my CNC router.
@43braden3 жыл бұрын
“So there’s a simple and easy way to ….. all you need is every tool in the shop, paper, business cards, tooth picks, gum, paper clips” 😂 love you Rob but this was CRAZY busy!
@dashriprock57203 жыл бұрын
The guy takes a little time to plan and design according to it's use and you call that crazy busy? Do you get headaches at simple math too?
@blahh3973 жыл бұрын
Excellent video, as always
@RobCosmanWoodworking3 жыл бұрын
Thanks for commenting
@thefleetfarmer18153 жыл бұрын
I’m anxiously awaiting your Bench Flattening videos! 🙂
@RobCosmanWoodworking3 жыл бұрын
Ok. Coming soon
@waratahdavid6963 жыл бұрын
Love you approach and professionalism Rob. But seriously mate you need to move to metric, that inches and fractions is doing my head in.
@RobCosmanWoodworking3 жыл бұрын
Not happening. I grew up on imperial and this old dog is not changing now
@colinchesbrough5772 Жыл бұрын
I often thought of myself as a loner...a true "wood freak", if you will. Then I watched Rob pare micro-fibers of wood with his chisel, just to get a flawless half lap joint on two tiny pieces of wood, in an obscure drawer he may only go into a few times a year. Then I felt much more normal
@jimsjacob2 жыл бұрын
I don’t know what it is, but I find that Shooting Board oddly satisfying…
@RobCosmanWoodworking2 жыл бұрын
has something to do with the efficiency I think
@McMonkeyful7 ай бұрын
Nice video. I need to make some of these up for my workshop & kitchen. I have to say what torture it is for the ears to hear the imperial measuring system. 16 eighteents minus 14 32nds x 9 fifteenth of an inch. How do you do it? I'm from the UK where we are still half & half imperial/metric & I do use imperial measurements when doing large projects, but as soon as I'm working on anything detailed that requires a level of precision or any calculation, it has to be metric. So much easier to work with.
@philquinn738 ай бұрын
What species of wood is the one in the middle that looks like red marble? It’s beautiful!
@virtualfather3 жыл бұрын
What if you roughed out to the boards cut the slots and then playing the boards to fit the slot would that be quicker and easier
@RobCosmanWoodworking3 жыл бұрын
then your slots would not line up with each other as you could not plane exactly the same amount from the ends to fit the drawer
@markb2763 жыл бұрын
"I put them in a bit of order" See what you did there Rob 👍😁
@RobCosmanWoodworking3 жыл бұрын
Well I cant be perfect all the time!!!!!
@garryverniest5893 Жыл бұрын
I've watched a fair number of your videos. You do incredibly fine work but OMG you are building shop cabinets. Set up the dado blade a giter done. I hope your mrs. gets that much attention.
@RobCosmanWoodworking Жыл бұрын
Garry, my shop is my showroom, folks come here with high expectations and I can’t disappoint!
@szymonz.75423 жыл бұрын
9:13 I really love that whispy sound!
@RobCosmanWoodworking3 жыл бұрын
Music to my ears
@peterscott136410 ай бұрын
Most helpful! Do I spy an APDS round lurking in the background...?!!
@RobCosmanWoodworking10 ай бұрын
Yep! Al, retired tank commander, Strathcoma, Canadian Army, works here and he gave me his first round he fired.
@matthewmarello1347 Жыл бұрын
1/8 to 1/4 dado every half inch or so on center not glued in so you can change it as needed. Add or reduce dividers.
@dpmeyer48673 жыл бұрын
nice
@MrMemusashi3 жыл бұрын
Either we got a new camera man or someone has learned the need for close ups......thanks Rob and crew!
@RobCosmanWoodworking3 жыл бұрын
Same old camera man. Jake
@garybadger3253 жыл бұрын
I have a question...Why did you not cut the notches for both horizontal and vertical pieces at the same time? It seems that it would elevate alignment errors. Thanks again for your videos. Enjoy watching them.
@christianestrada53623 жыл бұрын
I used to always put dividers in stopped dados to keep them fixed. I think I'll do them this way from now on since the extra work is too hard and unnecessary. Having the dividers fixed in place also makes it harder to clean out the bottom of the box.
@RobCosmanWoodworking3 жыл бұрын
I agree
@johnyb9884 Жыл бұрын
What did you mean “I want the bevel on the inside” when you flipped the piece and cut lines at 1/2 height? 14:52 mark in video
@J.A.Smith23973 жыл бұрын
Elegant
@RobCosmanWoodworking3 жыл бұрын
Thanks for commenting
@williamfitzer48053 жыл бұрын
An adjustable stop that allows micro adjustments would simplify that a lot.
@andrewbrimmer1797 Жыл бұрын
I hope this question isn't as silly as it seems to me. I tried to reclaim wood from a pallet and also from a bed. The wood just seems too dry or something it just splinters. Is some wood just too low a grade or too old or dry to use or is it my skill is not developed
@TheSmiley3162 жыл бұрын
Pack of cards.
@clemensmartin38963 жыл бұрын
You could also fit the assembly using felt like you would a humidor divider
@RobCosmanWoodworking3 жыл бұрын
I dont smoke so I am not sure what that is all about, can you explain?
@clemensmartin38963 жыл бұрын
Sorry about the double post, lost my mind there, just for a second. If you leave the pieces with a bit of “wiggle” room, you glue a strip of felt to the ends. It will fit snugly, and because the felt is on all ends, the assembly won’t move. Also, there will be no chance of altering the fit of the drawer.
@northernbrent63343 жыл бұрын
Great video… something tells me you like Lee Valley
@RobCosmanWoodworking3 жыл бұрын
Thanks for watching and commenting
@nialstewart82633 жыл бұрын
Rob, you took longer to cut those slots on the table saw than by hand (after editing). Years of experience! :-)
@RobCosmanWoodworking3 жыл бұрын
When doing small runs hand tools are almost always faster than power tools
@michaellinahan77403 жыл бұрын
Rob, good video. I would use the kerfmaker to set the width of the notches, it saves a lot of mucking about. Also is that a repair on the back edge of the dovetailed drawer at 1.25 and is that face piece some sort of burl?
@17penobscot3 жыл бұрын
38:05 If Rob pulls a hair out of his head....😆
@richs54223 жыл бұрын
Too cheap to spend $120 on a joinery blade for the table saw, so I picked up a TCG melamine/laminate blade on sale. It left corners that needed clearing for a year and then I had it sharpened, but told the person sharpening that I was going for a flat top grind. That made the corners a lot smaller and easier to trim. It's out for the second sharpening now, should be pretty close to perfect. With 80 teeth, it works really well cross-cutting joints in hard woods.
@RobCosmanWoodworking3 жыл бұрын
Let me know if it gets a true flat grind on the top when you get it back from the sharpener
@richs54223 жыл бұрын
@@RobCosmanWoodworking Looks perfect to me without magnification; at 20X there's a few thousandths bevel on one side, maybe 2-3 thou? Sorry, said it wrong above. The blade started out as a laminate/melamine blade. It's good to go for cross-laps and kumiko now. Not much of any rake angle, but cross-cuts ash just fine. It's sorta close to a specialty joinery blade on the cheap. On the other hand, I've never used an ATBR blade. 50 teeth is a bunch, but they seem to have a fair bit of rake. How much rake would one want in a joinery blade?
@memo12693 жыл бұрын
I don't understand the table saw safety disclaimer. Use the saw however you see fit, i really don't care, but you tout all of these videos as educational. And I can't imagine that in your Purple Heart Project classes you're teaching the students like this. Surely more than a few come to you with fully or partially missing fingers or limbs. Don't take it the wrong way - I've learned a ton from your channel and I'll keep learning as long as you're teaching. I'm not the safety police guy, but this particular case just strikes me.
@RobCosmanWoodworking3 жыл бұрын
I put the safety disclaimer in there to ward off the numerous emails and comments about how I am doing it wrong etc. etc. if I didnt put that disclaimer in.
@danimalmaxasis27622 жыл бұрын
Me continued... next I would decide on my distance between 1in 2in 3in cetera... using a box joint jig simply cut into all parts at whatever interval you decided... I would do probably every inch... once you make all Cuts in all parts... simply put parts together as necessary to accommodate space as necessary
@bobbenzuly78933 жыл бұрын
I love the tightness you get side-side and front-back. Seems like it would be difficult to take the dividers out if your needs change later. Any tips how to get it out?
@RobCosmanWoodworking3 жыл бұрын
they come out...you just have to pull them out all that the same time and not get it twisted so it jams against the sides of the drawer
@yannickbourassa25543 жыл бұрын
Using fingers as a push stick. I'll try that. Because it's a beginner video for beginners.
@RobCosmanWoodworking3 жыл бұрын
Knowing where your blade is and where your hand is in relation to it, is the safest thing you can do.
@johncoops68973 жыл бұрын
He's cutting 2" wide stock. Imagine Yannick trying to use a bandsaw or a nail punch!
@markh74303 жыл бұрын
Could you state the brand and / or provide a link the the set of height setting gauge blocks used for the table saw blade height at 31:45 please? Thank you.
@lawman55112 жыл бұрын
I can’t believe you got away with those rip cuts on the table saw with all your fingers.
@darrylbrook59683 жыл бұрын
Could you use one of those “kerf gauges” to set each cut thickness for the table saw? Don’t have one my self but have been intrigued enough with the samples I have seen online to make one like the Andy Klein version as an example… but as all the others have already stated loudly…. A threat example of how it is done well. Cheers from Western Australia.
@RobCosmanWoodworking3 жыл бұрын
I know what you are talking about but I have never used one so I cannot comment. I just take my measurements right from the wood as shown...no need to spend money on another jig
@bobd.3 жыл бұрын
Couldn't you set two stops, one on each end (left and right) of the piece so you could cut the notch for multiple pieces without having to stop and reset your one endstop. Then flip the divider and cut the other notch providing it's the same distance from the end.
@RobCosmanWoodworking3 жыл бұрын
Sure you could do that. I just prefer working form the same end. I guess my brian thinks its more accurate somehow
@donpeterson92823 жыл бұрын
Always use a push stick on the table saw when your fingers are within 6 in of the blade. Hooking the little finger over the fence does not provide an adequate level of protection.
@Zaranathax2 жыл бұрын
It's OK, he's 'experienced' which means his fingers won't be cut off when he inevitably puts them in the blade.
@matthewmarello1347 Жыл бұрын
He's old enough to make the decision on his own. Thanks mom.
@jethropebs3 жыл бұрын
Love the videos Rob! Sorry if you addressed this already or somewhere on your site, but can you state the reason why your planes cannot be shipped to the U.S.?
@RobCosmanWoodworking3 жыл бұрын
As part of our distribution agreement with Woodcraft we don’t ship them into the US so as to not step on the toes of the individual WoodCraft Franchised stores.
@farmerjohn87263 жыл бұрын
Feeler gauges too crude! Marking gauge as paring chisel ... astonishing! Next we'll find out that its cutting wheel is high speed steel and that there's a Wolverine sharpening jig for a CBN grinding wheel ... that was the ultimate in hand tool accuracy! ... and that was for a tool drawer! "Honey, close your eyes! The fit is better than in your wedding gift jewelry box!" Cheers, Farmer John, Ontario, Canada
@RobCosmanWoodworking3 жыл бұрын
Next video: why the dog house needs to be made with dovetails!!!!!!!
@reidmoule33583 жыл бұрын
What was that fine cross-cut saw at 43:26?
@befmx313 жыл бұрын
Rob, where do you get the headgear with the magnifiers in it? Thanks.
@chasingzeroscrypto1502 жыл бұрын
What marking knife is that?!
@philmorris15703 жыл бұрын
Rob, why don't you make a marking gauge with the wheel flipped? Then you could score the inside line without needing a panel gauge.
@RobCosmanWoodworking3 жыл бұрын
You can do that, and I’ve had to do it plenty of times before. The issue is that the shape of the cutter either pulls your marking gauge toward the board or away from the board. I will usually only do that if I find myself in a situation where I can’t use a different tool.
@robbyyant62133 жыл бұрын
Oddly enough, I'd just been working on a tool chest and trying to decide the best way to make the dividers. Do you miter the ends of the sidewalls/perimeter pieces where they meet in the corners?
@RobCosmanWoodworking3 жыл бұрын
Yes I do!
@Haforn-ng2vy3 жыл бұрын
Rob, I am curious as to why you use the marking gauge instead of the square using the reference edge to transfer the marks across the top and on to the opposing face? Is there an issue with using the square or is it just preference .... as not all of us have the longer gauge
@RobCosmanWoodworking3 жыл бұрын
I just trust the marking gauge more than squaring around with the knife. Squaring around is fine 99% of the time and the wood is so small here that using marking gauges I admit is overkill.....but that's just how I roll I guess
@ZacEckstein3 жыл бұрын
I was hoping you'd show how to glue or attached the dividers into the drawer more permanently, which is what I always have trouble with.
@RobCosmanWoodworking3 жыл бұрын
I dont permanently attach mine, i want them to be removable in case i want to redo the grid
@przybyla4202 жыл бұрын
Tiny nails or little bamboo skewers as dowels would work well. I like the ribbed nails, they hold a lot better. For hidden bamboo dowels, use a 1/2” thick plywood template to locate where to drill the holes, drill through the guide hole in the template, and point the ends of the dowels to give some leeway.
@whittysworkshop9823 жыл бұрын
I know this is a "halved joint" :) im a bit OCD when it comes to my tool drawers too, hate it when stuff is loose to roll around. Everything is either divided off you like have done, or bigger tools have "holders", nearly like theyre french fitted :) Good camera work too Jake, some really good close ups :)
@RobCosmanWoodworking3 жыл бұрын
Yup loose stuff in drawers drives me nuts too....we are OCD together
@locduc63742 жыл бұрын
What sells fast?
@batavuskoga Жыл бұрын
Why don't you cut all the pieces and also the joints by the table saw ? Much faster and more accurate and even easier.
@johncoops68973 жыл бұрын
A fixed size divider like this is hard work to build and VERY inflexible. It's far better to use a series of rebates in full-width LeftRight dividers, then have a set of movable inserts for the other direction. That way, when things change (which always happens) you don't have to re-make the whole thing, you can just move the dividers around. If you use 1/8" ply for those small dividers, you can just use standard table saw blade cuts as the rebates.
@RobCosmanWoodworking3 жыл бұрын
That will work...but doesn't give me the fine craftsmanship look and feel I demand of myself
@mehmetguzeldere59953 жыл бұрын
Hi Rob, what kind of wood is the small drawer's face?
@RobCosmanWoodworking3 жыл бұрын
Doug fir
@mehmetguzeldere59953 жыл бұрын
@@RobCosmanWoodworking Thanks for getting back quickly. The one I asked was the red/black color wood.
@RobCosmanWoodworking3 жыл бұрын
That’s some Claro walnut Burl
@mehmetguzeldere59953 жыл бұрын
@@RobCosmanWoodworking Thanks much Rob!
@ianjay32863 жыл бұрын
Another great video. What i've noticed about the back of your drawer box's you don't plane the drawer sides down to the backs after the glue up. Is there a reason for this, I know its only seen when you remove the drawer from the carcase.
@RobCosmanWoodworking3 жыл бұрын
I talk about this in my drawer making series, so for the details see it. I like the back lower to make it easier to get the drawer in an out
@johncoops68973 жыл бұрын
The sides need to be a certain height so that the drawer works. You cannot plane them down after glue up, because that would make the drawer loose! If you make the back the same height as the sides, then you cannot easily close or open the drawer, since the air (behind the drawer) has no way to escape.
@KimbrellBrad3 жыл бұрын
@@johncoops6897 Exactly! And when you work to Rob's standards of a piston-fit there would be no way to get it to stay closed LOL!
@johncoops68973 жыл бұрын
@@KimbrellBrad - you could drill a large hole in the rear of the casing, then connect some duct tubing. Instant bellows for your iron working forge!
@williamfitzer48053 жыл бұрын
Hahaha…your using your fingers as a push stick that close to the table saw blade is a huge no-no. But I do it all time too. 🥴🥴
@RobCosmanWoodworking3 жыл бұрын
Not if you know how to have positive control on your wood. You will note that I loop my finger on the edge of the fence to keep my hand tied to the fence and my finger away from the blade. I pay very close attention to the cut and I have 100% control of the wood. This method is NOT for those who cannot achieve these critical elements, but done correctly and EVERYTIME it is a safe procedure
@williamfitzer48053 жыл бұрын
@@RobCosmanWoodworking I agree. I do the same. I keep fingers over the top of the fence as well, while applying downward pressure on the wood as I push it thru. The standard ‘safety protocols’ however say to never do that. I have been doing it also for many years. I only have had a riving knife on a saw for two years, so I get it.
@aljones47193 жыл бұрын
Longest size is length, usually along the grain. The middle size is called Width and the thinnest size the thickness. Keep cosistant to enable learners to get the correct terminology. I started my woodwork learning 66 years ago and am still learning.
@mick147313 жыл бұрын
It's a little intimidating as a beginner too see 5 different tools used just to lay out a notch.
@RobCosmanWoodworking3 жыл бұрын
Well you could just use a knife and a square and carry your knife marks around. I just dont like to do that in case your wood in not perfectly square, but I must admit its a little bit of an overkill. Just carry your marks around with the square and knife, you will be OK
@steviebye13 жыл бұрын
I love all of your work, but please America go metric and save my poor British brain.😄😄
@RobCosmanWoodworking3 жыл бұрын
Thats not going to happen. They tried it in the 70’s and the public revolted against it.
@michaelroy5427 Жыл бұрын
Are GREY sofas out of fashion?
@jmpsck233 жыл бұрын
First comment!!! 😆🤣😂
@RobCosmanWoodworking3 жыл бұрын
Yahoo….2 gold stars!!!!
@Zaranathax2 жыл бұрын
There are much easier and quicker ways to do this on the table saw: use two stops, one on either side, to cut the slot to the dimension of the smallest one, then remove one stop and refine by adding paper or whatever to the remaining stop. Also, don't ever, ever arrange wood on the saw with it running.
@virtualfather3 жыл бұрын
Planed not playing
@RobCosmanWoodworking3 жыл бұрын
Thanks for commenting
@weibullguy11 ай бұрын
WARNING: Even if you ARE as experienced as Rob, use a push stick.
@cranelift3 жыл бұрын
good vid but to much camera movement
@jcoul1sc3 жыл бұрын
You really don't need all this unless its high end. Just butt joint snug fitting and glue it well. I have and never come loose.
@RobCosmanWoodworking3 жыл бұрын
depends on what quality of woodworker you want to be
@setdown23 жыл бұрын
I think you can make it even more complicated...😩
@danimalmaxasis27622 жыл бұрын
Man I am sorry I could not watch anymore after about halfway through you need to productionize this let me help you out a bit... I would measure the width of my drawers and then the depth of my drawers whichever is the longer I would call that the length whichever is is shorter would call the width off the bat... Now set up your table saw for your depth of cut to be halfway into all parts length and width...
@raynierllewis2827 Жыл бұрын
Please switch that machine off in between 😮
@kreech682 жыл бұрын
IMHO, that level of table-saw trimming/tuning is "ridiculous". There are SO many little steps involved, it's prone to failure. The video is interesting and gets a thumbs-up, but that parts gets a thumbs-down from me.
@stephankraft347 Жыл бұрын
9:25 into the video; experienced or not! Rob should not be showing that!!
@RobCosmanWoodworking Жыл бұрын
Why? I have full control, I have two fingers sliding on the fence, and to top it off, I’m using a SawStop. I put the disclaimer in there so I can do whatever I want, but if you’re not comfortable, use a push stick.