You don't have a camera treepod?

Do this changes with the "springer" bring more power to the gun?

Great video ! Accept Jesus Christ before it’s too late. Christ is coming very soon.

Que medida es el o ring

how much is the thread of the pressure gauge rifle cricket carbine

Có bán con ốc chỉnh lò xo bứa ko😊

Hi I found your video helpful even I am not using cricket, I have Vulcan 3 the 500mm and I want to ask a question about adjusting the FP without changing original spring, is it possible to loose the retainer a little bit? Which will give less stress on the original spring?

Thank you 👍🏻👍🏻👍🏻👍🏻

Congratulations on the channel. Some questions to help me out. Is this system the same as the one in the Cricket 2 WSA? Can I increase the regulator pressure just by opening that Teflon seat very, very slightly without needing to adjust the regulator plates? Thank you 🙏🏻

Muchas gracias amigo,solucione este problema, gracias a tu conocimiento que no has regalado,muchas gracias de parte de un mexicano, saludos 👋hasta donde te encuentras de parte de un mexicano🇲🇽

My cricket has air coming out of that valve, could you tell me why that happens and what should I do?

My cricket has an air leak, but I don't know which of the two regulators is failing😢

Now I understand why my cricket leaks air through the regulator and I haven't been able to go hunting for pigeons for 1 year. I think I need to put new o rings on it🤔,thank you very much bro.

thanku so much sir 💯

Any chancenof doing a video like this for the boss owners... we have been left out when it comes to these types of videos... I'd like to know exactly what I'm doing to adjust and repair my regulator.. and gun

Ernest My hammer is stuck projection out in the firing position. Connor retract it with the cocking arm. Essentially it will NOT cock?

How are you sir I need regulator tester for vulcan air gun pl help

Excellent video. Congratulations. A question, WHAT is the best regulator value for a cricket tactical II 60 in .22 caliber for 50 meters? Thank you so much.

Help i had my hunter compact apart cleaning it up. Put it all back together and had a huge poi shift. Probably should of market the position before removing the sleeve. Any advice ? Was thinking spinning the liner in 1/4’s and seeing if it shoots close to where it was ?

R3m, r5m or Kalibrgun cricket gen1???

Hi Ernest, I'm having trouble with a leak from the first hole from the valve assembly low pressure side I have used 2 lots of o rings with the same result leak from first hole from the rear is ther any thing else I could be missing other than o ring 8 thanks for any help

Useless. How do I adjust the regulator on my Bobcat. You only showed how to remove it. I need to bring it back to 130 bar as it is 120.

Greetings from France Sir. If you come back arround here, just a quick question. My Cricket (carabine model but same mechanic I guess) has got a sudden loss of power. When I got it, it was shooting between 260 & 263 m/s. Now, it's only between 220 & 223 m/s. Any idea where the missing 40 metters per second are gone ? I can't hear any leaking. I was thinking about a problem with the regulator but well, the shots are well regulated, just like before when it was shooting at 260. Just, now, it's regulated between 220 & 223 instead of 260 & 263... I'm not sure what's happening. Your thoughts would be appreciated. Thank you !

Are you out there no videos in long time Trying to contact u ..

Hi I’m wondering if anyone can help please my .22 crown mk2 after a service of the regulator isn’t showing any pressure on the gauge I have done a few services on my 2 crowns and I’m stumped I did seem to have a blow back from the side vent but it all seems fine when I took it out to check there’s no leaks whatsoever 🤔

I can’t adjust my FX Crown MK1 for pellets. Slugs no Way… What’s you recomend ??? Thanks

Can you do an update video for the new style barrels

Ok. A minha vaza no buraco abaixo da válvula, eh uma válvula huma aonde pode ser o problema. Na verdade o cilindro está en Zero ar y não enche já sai direto o ar ali no buraco abaixo da um.

I have FX bobcat MK2 in.25 cal, can i remove sylender with out degas the airgun

Great a $200 break line with rifling smashed into it. 🤡

Có bán nắp bịt đó k

Hi Ernest! Love your film. Could you please make a film about how to install o-ring C39 into the Crown mk1 house fot the tegulator? I have very hard to install it. Best Regards Rolf

Como vou saber que válvula usa la mía. Si hay una de 8 mm y una de 10 mm?

Благодаря за видеото!

After removing my gen 1 crown regulator and replacing the adjustment screw and piston. I still have about a 10 bar leak overnight. The culprit should be the oring at the bottom of adjustment screw. But it’s new. I took a close look inside the regulator body where that oring seats. And find tiny scratches in the body. I’m now attempting to polish them out with metal polish liquid and a q tip on a drill. Just remove some of the cotton till a get a semi firm fit. This maybe why some new crowns have creep from the factory.

Sir , i m from India and I have fxcrown.22 mk1 and regulator is already set at 150 bar but i want to know how many time tighten my power wheel spring for good fps and smooth functioning. Please reply i m waiting 🙏🙏 I have not chrony 😭. Please give Idea/approximate no. Of Crank to power wheel spring

La isiste vos ala valvula reguladora

Hoi Ernest, happy New Year! Can you do the dismantling of the cricket II? I want to install a Huma Air regulator but can't find a manual! thanks in advance

That spring is to long which restrict the air flow

Good day. May I ask what is the size of the manometer on crown. Thanks

Hi How do you remove the stainless adapter from the tube? it feels glued on my M3. I need to remove it as the seal inside it came out with the other 3 o rings :(.

@ ernest How i can do i cant put the part that is on hammer is more big

I have 50 bars per day leaks in my Fx crown. Both gauge always show same pressure. What part could be the reasons 🤔

Thanks for video… very valuable Where can I get the regulator tester?

The 8x1 o ring that you don't have a tool for. How and where exactly does it go in? My impact is missing that o ring and I'm trying to figure out how to put it in. Mine is a .25 so its a 9x1

Amigo entones para Mallorca potencia hay q apretar poco verdad

Hi Ernest apologies if you've made a correction, but at 3:09, the o-ring is 4x1.5 (it is on mine and in the service kits) Best regards Mark.

Hola estoy interesado en aumenta la potencia de cricket kalibrgun me podía aconsejar por favor

Where did you buy the gauge tool?

Thank you for these videos. After years of good service and a few o ring changes my R3 is all over the place! power wise. I think i need a few new parts. Could you let me know where i can buy regulator parts ? I am in the UK. Many thanks.