Thank you. Fun video to watch! I’d be curious to see what solid point slugs out of the Panthera would do in next one!

Outstanding work! Don't be down on yourself. We now know which pellets/slugs offer effective penetration. Looking forward to part 2.

04-23-2023 12:53 a.m. (my time)(Sunday morning). This is what I would be interested in seeing you test, using .30 cal. hollow point slugs (as heavy as possible), glue steel bearings (slightly smaller than the .30 cal. obviously), at max power on the rifle and shoot around the sticker to prevent the slugs from stacking on each other. Do the same thing again using copper coated pellets, make sure to keep them from stacking on each other, see how this perform versus the steel bearings. Use the rifle that will give you the most speed & power. I hope that you see this comment before you do the 2nd round of testing on that bullet proof glass. And yes, please use safety glasses. Thanks for sharing.

Something different, good video and very interesting! Good luck at rmac! Are those zan premium pellets sorted for size and weight? Have you found them to be more accurate than the jsb 44’s or 50’s?

Good job. Looking forward to part 2 comparison.

I suspect that panel is made out of Lexan, at least the outside layer. Bullet resistant panels are made of layers “glued” together, and they gain their useful properties because the impact energy is used up defeating each layer’s structure and the adhesion. The bubbles you see growing is the adhesive giving way on the outer layer. You may be right about it being “backwards” and I look forward to part two!

Great video!! What are your settings on your 30 cal for pellets??? 👍🏻 thumbs up

More like this please, especially with the impact

Really found your video interesting because No One in airgunning has done this before! While you used the term bullet proof glass, I'm familiar with it as BR glass... meaning Bullet Resistant glass. Either way I found it interesting to watch, so thank you for putting it together and sharing. There has to be a scientific explanation of the spreading pattern? Perhaps something to do with a chemical process formulated to displace heat while absorbing the impact of a projectile. Hope you have a great time at RMAC!

Interesting. Thanks man.

Would have been better shooting random spots instead of trying to group. I know you said you’re not trying to group but clearly you were. It would be nice to know if that glass is weaker with different areas being shot

Very interesting thanks for sharing

Dude, please wear eye protection on these experiments!! Other than that, great video, keem them coming!

Thats pretty koo buddy great job thanks for sharing bsafe buddy 👍

While shaking m3 up down does it make sound, mine does is there any fault, sound comes from the valve/hammer area,like something is sliding back and forward,

Thanks for the video. Great work. Must have taken a lot of time to make.. Shooting it from the other side ? I think (70/30) the pellet will be stuck in the same depth. Anyways. If the pellets did not exspand (where made of steel)..The .22.. 34 Grains. 1000fps. Would have the best potential for penetration..34G at 1000 FPS is 102 J.. Front area is 23,75 mm2..A .30 pellet has a front area of 45,6 mm2..So a .22 at 102 J has the same J/mm2 as a .30 at 196 J.. A "small" .357 Magnum handgun has between 550-800 J. Front is 64,5 mm2..Or the same J/mm2 as a .22 at 203- 295 J..

Mooi gemaakt Kan niet wachten om te zien wat er met de andere kant van het glas gebeurt. En veel succes bij RMAC

FX Airguns are for tickling squirrels... Try AEA next time.

So you want to draw attention to air rifles in attempt to more rules and regulations. Nice job. Keep up the good work

Mooie video weer toppie 👍😉

Make a video and see how many shots with the 30 cal impact it takes to go through the bullet proof glass, cool results and good luck at the competition 👍👍👍👍👍

Acril glas laag. Meest transparant, warmt op bij wrijving en vertraagd projectiel. De lagen er achter zijn meestal triple gelaagd getemperd glas. Hoe ze het precies doen is wss aan Saint gobain om het uit te leggen

I use 1/4 “” ( 6.35mm ) Acrylic Plexiglass . It will stop a 50 cal 250 grain slug going 700 fps . (272 FPE )

Ha ha ah😅 finally now you are thinking out of the box. 👌

Thank you for posting it very interesting 🤕

I wonder what happen if you shoot it with 72 cal Zeus.

Try .177 HN hornets going as fast at you can shoot them. 😂

i designed a .457 slug for bullet proof glass. But I dont have the glass. Im too afaid to fire them out my bulldog.

Yoooooo my friend

It is a polycarbonate not glass as we know it. You can bend it in a sheetmetal brake. Stuff I have is brand Lexan

Forgot the 👓?

😁😁😂😂😂🤣🤣🤣🤣🤣🤣