G37 Brake light Halo install Step by Step DIY (GTR BRAKE LIGHTS!!!)
Рет қаралды 66,065
4 жыл бұрынIn this video I will show you how to remove your brake lights from an infiniti g37 and install halos in them to look like the nissan gtr taillights
--------------------------------Wiring Configuration-------------------------------
Factory to DIODE DYNAMICS
Black to BLACK
Green with yellow strip to YELLOW
Green with white stripe to WHITE
Green to RED
--------------------------------------------------------------------------------------------------
IG: @g37supreme
Car Club: @876ix.lifestyle
----------------Affiliate links------------------
-----------Items you will need-------------
1. Rotary tool Wired: amzn.to/3pMlTFz
1a. Rotary Tool Wireless: amzn.to/3QB48V8
2. Diamond Cutting wheel: amzn.to/3CjH3SH
3. Tail as turn module: amzn.to/3AtLyZw
4. Rust-Oleum Primer: amzn.to/3bYJAHr
5. Rust-Oleum Gloss Black: amzn.to/3AwfmEY
6. JB Weld Clear Weld Quick Setting Epoxy, 2 packs: amzn.to/3AvXx8V
7. Tarnish Resistant Silver Wire: amzn.to/3SWNjFU
8. Diode Dynamics 110mm halos with red driver: amzn.to/3Qzc8WZ
9. Diode Dynamics 90mm halos with red driver: bit.ly/3vDOkZl
10. Diode Dynamics 90 and 120 red 4 pack: amzn.to/3pqPG6r
@taylor_galster 3 жыл бұрын
You’re awesome for this. No reason to pay someone $600+ to do this when it’s not too hard of a DIY. Thanks for the great video
@1BuildMedia 3 жыл бұрын
Glad it was helpful!
@mannygee5111 3 жыл бұрын
Been trying to get these done for my 2007 Infiniti G35s sedan. Just took some spare ones to a shop down the street for me to see if they would know how to do it. They have the slightest clue. This is very much help that I will try and do on my own now and save money. #project 👏🏼
@jakemannino5344 3 жыл бұрын
You a 🐐 for making this video bruh
@deonpalmer8758 3 жыл бұрын
Real goat
@MIKEMARBLES 3 жыл бұрын
Excellent I'll definitely be doing mine. Looking for the spiralling effect. Thank you you're appreciated
@G37keith 3 жыл бұрын
Great video been wanting custom tails and honestly didn’t want to pay the price for them 👍👍
@ksich8142 2 жыл бұрын
I like this a detailed simple video , shows how to do everything , very creative and dope lookin mod thats actually custom , not just a sticker or blacked out tail lights
@pablocalvillo8921 2 жыл бұрын
Wow the best dioded dynamics halo video out of all here on KZfaq dyi with wiring details helps a lot!!!
@1BuildMedia 2 жыл бұрын
Glad it was helpful!
@VQMASTER 3 жыл бұрын
Just ordered everything! Found an extra set of tail lights in a scrapyard for $66! Let the project begin...... well I guess thats when DiodeDynamic gets the stock back in. Lmao
@e7bk 4 жыл бұрын
Best informative video on KZfaq
@1BuildMedia 4 жыл бұрын
Glad it was helpful!
@rg5856 3 жыл бұрын
Thanks man you really inspired me to do this on my own. I appreciate you 👍👍👍
@1BuildMedia 3 жыл бұрын
Glad I could help
@_.._i Жыл бұрын
Your the only one with good instructions
@conito925 2 жыл бұрын
What a life saver, thank you bro
@tonytonytony87 2 жыл бұрын
Real yaad man big up fam, I appreciate this vid
@bobmotherfuckinsmith3089 3 жыл бұрын
When you use a rotary tool the trick is to keep the rpm up high and not let it get dragged down so hard. It's like using a chainsaw but 17 times smaller.
@coreymorgan7310 3 жыл бұрын
About a hundred of these views are from me but I'm almost done, and without this video I probably wouldn't have attempted it, I would have paid someone's high price. So thank you
@1BuildMedia 3 жыл бұрын
This is what its about for me. I'm glad you are attempting it
@dakhangsta 2 жыл бұрын
That looks amazing
@juniorcts9747 2 ай бұрын
Hey got a question, currently working on a project doing the quad halo set up. I have the red halos going from black>to black Red> green , white> green and white And i have the switchback halos yellow> green with yellow and i have the black fused with the black from the red halos both going into the black from the oem harness. However when i brake the ambers turn on instead of the red. Any idea why? I only have black and yellow going to the harness.
@e7bk 3 жыл бұрын
What if add antoher ring but smaller to light back up I think it gonna be like Supra MK4 aftermarket tail light
@xpantherroo9083 3 жыл бұрын
Good looking on the video mad props!
@1BuildMedia 3 жыл бұрын
Appreciate that
@Mrquietstom2022 3 жыл бұрын
You can charge 5-750 easily for this and be backed up for months! Great tutorial sir
@nonameisthename138 3 жыл бұрын
You ain't lyin!! 🎯💯 With him showing how to do it, those who are brave enough, can tackle it themselves..
@1BuildMedia 3 жыл бұрын
Cool, thanks
@shaunoguinn1015 2 жыл бұрын
I do it for a living and I typically stay busy doing it.
@shaunoguinn1015 2 жыл бұрын
I'm actually doing a set right now as we speak lol
@xxoncorektsxx4179 11 ай бұрын
@@shaunoguinn1015Do you have any 90mm I can Purchase of you?
@josediegosilvasolis2247 Жыл бұрын
You inspired me to make my own , boss you are the best doing this video 🫶🏽🫶🏽
@MassiveAutoAddiction-wu9od 2 ай бұрын
How do you get the big red piece back on after you cut it out.
@elmangador7 3 жыл бұрын
Great video bro..
@1BuildMedia 3 жыл бұрын
Thanks for the visit
@vladz3654 4 жыл бұрын
90 and 110mm rings
@1BuildMedia 4 жыл бұрын
yes that is correct, you need a pair of 90mm and a pair of 110mm see the links in the description for diodedynamics,
@christians8114 3 жыл бұрын
@@1BuildMedia is a coupe the same?
@1BuildMedia 2 жыл бұрын
@@christians8114 apologies for just seeing this. I dont want to steer you wrong. I am not sure.
@tyreseewing4574 2 жыл бұрын
@@1BuildMedia can I use a 80mm or even 100mm cause I can’t find 90mm anywhere
@1BuildMedia 2 жыл бұрын
I'm sure you can make it work
@Rick_B52 3 жыл бұрын
Really nice mod!
@Solo-lo4ix 3 ай бұрын
So the diode dynamic turn and tail won’t work for halos ?
@Stock.Foreign Жыл бұрын
how do u disconnect the plastic connecter ?
@Angelg37s 9 ай бұрын
😍 I need this 😩
@wrkls_ 4 ай бұрын
Could you not wire the halos directly to the circuit board?
@larrysmith2647 2 жыл бұрын
Looking to try this on my G35
@Jordan-vy6fp Жыл бұрын
Hey man, great video. Helped through a lot of the work. Although, I’m having a slight issue, all of my things work except they don’t turn on when the headlights are on. Turn signal, lock/unlock, brake all work fine. But they don’t run when the headlights are on. Does it have something to do with the extra yellow off of the drivers? I didn’t touch those. Thank you
@1BuildMedia Жыл бұрын
Check the wiring config in the pinned comments
@jacobguitron9446 6 ай бұрын
Has anyone tried this on the convertible? Do the same parts apply?
@blessingshonor2137 3 жыл бұрын
Blessings fam...🇯🇲🇯🇲🇯🇲
@1BuildMedia 3 жыл бұрын
respect!
@imreeflexx1878 3 жыл бұрын
great video 🔥 will be attempting this soon will it work on my g37 coupe?
@1BuildMedia 3 жыл бұрын
I am sure the process can be applied
@user-jw7rr2zd1y 4 ай бұрын
Did you use 110 or 120 mm
@yusufkadi5304 3 жыл бұрын
I plan on tinting the taillights. How bright are the halos and will they shine through well? Also, how much did you spend for both headlights?
@1BuildMedia 3 жыл бұрын
Yes its bright enough to shine through. I spent about $230 i believe. Thanks for checking out the video, dont forget to subscribe
@deonpalmer8758 3 жыл бұрын
How’d you get the brake light in the middle the flash when you hold the brake boss man. + thank you so much for the video
@1BuildMedia 3 жыл бұрын
There is something you can buy that does that. You can find them on Amazon. Brake light strobe controller. They normally have the info on how to install it.
@jjamaya01 3 жыл бұрын
What would be the best way to color match the little part on the trunk with the reverse light? Tinting it maybe?
@1BuildMedia 3 жыл бұрын
That's right I tinted mine.
@shaunoguinn1015 2 жыл бұрын
If you open the trunk section and paint the housing with the same paint it will be identical to the main tail section. A little more work but perfect results.
@swainsonmckenley5850 3 жыл бұрын
Nice!
@aafaqvirk384 3 жыл бұрын
Is it possible to get amber tailnas turn? So normal red but turns to Amber when indicating
@1BuildMedia 3 жыл бұрын
Not with my method and what I purchased. They sell different halos with different drivers, check those out. Thanks for checking out the video, dont forget to subscribe
@ramongarrick2640 3 жыл бұрын
Big up 🇯🇲
@ez-duz-it9683 Жыл бұрын
What fits my g37 sedan the 120 or the 110? And does it have to be the red ones because I can’t find the 90mm red without buying the 120mm
@1BuildMedia Жыл бұрын
You should be able to get those to work
@MrTurbine777 3 жыл бұрын
You can avoid having to cut the housing by putting it in the oven at 350°. Just be sure to remove the ballast first to avoid damaging it. You then simply (and carefully) pry it apart. I didn't know this prior to watching your video and just now learned it since I'm thinking of doing similar. Thanks for the video!
@lulmoewiththegimpyleg6815 3 жыл бұрын
Try the oven method and post it.... cutting does seem kinda raw for me
@4DSCdude 3 жыл бұрын
i thought he was crazy cutting these up. i haven't tried it on my tail g37 lights but i've separated many lenses from headlights and tail lights by baking them
@37izzyyy 3 жыл бұрын
With Gs taillights in general you can’t bake them in the oven, there plastic welded to the lens, I retrofit and always have to cut the tails. Headlights easily go in the oven.
@1BuildMedia 3 жыл бұрын
Finally thank you.
@pablocalvillo8921 2 жыл бұрын
Who here has done the oven method instead of cutting them off ???
@dakhangsta 2 жыл бұрын
You have video on how you wired the halo to the OEM wires?
@1BuildMedia 2 жыл бұрын
See pinned comment
@Ray-il1jo 3 жыл бұрын
Awesome video supper informative and btw man how did you access the third brake light?
@1BuildMedia 3 жыл бұрын
I will do a quick video on that.
@davidgarcia9681 Жыл бұрын
If I added load resistors woukd I put them on the wires that came w the halos or the original wire of the tailight? (G37)
@1BuildMedia Жыл бұрын
That's a good question. You put them on the original wire that will also eliminate the need for tail as turn
@sanzonamckillit3763 3 жыл бұрын
You don't need the tails as turns modules. Sell em, and ditch them. You can wire directly to the OEM pigtails (ON/BRAKE/TURN) and will work fine. Maybe your issue is 1 driver trying to run 2 specific halos? Also, could just depin your wires, no need to cut unecessary holes. How is your seal? Why not use rubber buytl to seal those lights? Why ditch clear lens for halos? You recommend the 2 prime sizes for halo applications, however halo sizes can vary depending on application . FYI Halo sizes vary on build applications and builds can retain those clear OEM lens. All in all, thanks for the step by step and wish you the best
@zekekormos3917 3 жыл бұрын
This was lowkey a passive shady comment
@pablocalvillo8921 2 жыл бұрын
@@zekekormos3917 biggest hater on here bro if your so smart then please tell us how to do it without the driver
@juniorcts9747 3 жыл бұрын
Would it work if i do diode dynamics 110 mm and morimoto 90mm halos? diode is backed up for the 90mm . Sounds crazy but was just wondering
@1BuildMedia 3 жыл бұрын
Im not sure what morimoto connections look like. I wouldnt want to lead you blindly
@juniorcts9747 3 жыл бұрын
@@1BuildMedia another question did you have to use the t-tap connector ? Or the wire pigtails.
@juniorcts9747 3 жыл бұрын
Or did you just cut a bit of the cable and twisted both wires into one (for when using only one driver for two halos) . Also do you recommend using only one or is it better to use two?
@Usef320 5 ай бұрын
is it easy to take the trunk reflectors off too and spray those black? I dont like the mismatch
@1BuildMedia 5 ай бұрын
Three little bolts. I actually wrapped mine to match later on.
@ericwilkerson5 3 жыл бұрын
Is the lense glued on? I'm asking because I'd rather use the oven method to open the light instead of cutting.
@1BuildMedia 3 жыл бұрын
Yes its glued on. Its not like the headlights. You definitely have to cut
@MsFenix89 3 жыл бұрын
Taillights you can’t just open them by heating them up.. Is welded plastic so you need to cut them open..
@juliocampos3414 2 жыл бұрын
Anybody else have a white noise emitting from the speakers after installing? When I mute the audio it stops but once I turn it up even just one you start to hear the noise
@1BuildMedia 2 жыл бұрын
Check the comments you will see what i recommended for someone else
@bobmotherfuckinsmith3089 3 жыл бұрын
You can't use a heat gun to separate the plastic pieces?
@1BuildMedia 3 жыл бұрын
You can't no
@37izzyyy 3 жыл бұрын
Appreciate the vid brotha, any idea if it’s the same sizes for a g37 coupe?
@1BuildMedia 3 жыл бұрын
I am really not sure. I know the coupe has a bit of concave that cuts into the lights so you wont get the full halo for the smaller halo light, you would have to do some cutting to get it to fit properly there. Hope you find a video that helps.
@37izzyyy 3 жыл бұрын
@@1BuildMedia okay for sure thank you I subscribed🤙🏽
@juniorcts9747 3 жыл бұрын
did you end up finding the coupe size?
@37izzyyy 3 жыл бұрын
@@juniorcts9747 add my on insta. It’s the same as my name here
@370gtalej5 2 жыл бұрын
My tails are failing, the LEDS are going out. Is it possible to just do this to those?
@1BuildMedia 2 жыл бұрын
Just make sure it's not your actual wiring that's going bad. If not then you can proceed at your own risk of course
@juniorcts9747 3 жыл бұрын
Did you have to break the red thing that holds the connector/harness? Can’t seem to be able to take it off without cutting it
@1BuildMedia 3 жыл бұрын
I was able to take it out, but do what suits your situation
@juniorcts9747 3 жыл бұрын
@@1BuildMedia another question for the green wire , did you get rid of that bulb? Is it even needed? Or did u just tap it into that wire
@1BuildMedia 3 жыл бұрын
I'm not sure what you mean. Dm me on IG with a pic. g37supreme
@austintorreflores5104 3 жыл бұрын
How did you get the 3rd brake light to flash?
@1BuildMedia 3 жыл бұрын
I'll do a video soon
@swanknasty2527 3 жыл бұрын
Can u explain what wires to tap into u didn’t show us that part
@1BuildMedia 3 жыл бұрын
This is now in the video description and also pinned in the comments
@Liebs 2 жыл бұрын
Does this work if my driver taillight has the unlock button?
@1BuildMedia 2 жыл бұрын
Yes same principle applies. I have seem videos that details how to do it for g35 lights as well.
@rubixlighting1057 2 жыл бұрын
Did you get a whine from the cabin when you turned them on?
@1BuildMedia 2 жыл бұрын
with my factory radio no. with my tesla screen yes.
@josevilchez9829 2 жыл бұрын
Do you have to solder anything for this project?
@1BuildMedia 2 жыл бұрын
I didnt have to
@machneil1779 3 жыл бұрын
Are the halo sizes the same for the coupe?
@1BuildMedia 3 жыл бұрын
I'm not sure
@connorhearne8695 Жыл бұрын
Do we have to Dremel it or can they be heated and pulled apart?
@1BuildMedia Жыл бұрын
Dremel
@staticg4978 3 жыл бұрын
🤝
@marcusmaybin9505 2 жыл бұрын
Now I’m almost a gtr 😂
@cheyenne8735 Жыл бұрын
Hey bro, my right tail light is hyper flashing. Is there a solution to fix it ?
@1BuildMedia Жыл бұрын
Resistor or use the tail as turn
@iz1238 3 жыл бұрын
Same measurement as 2010 G37x coupe?
@1BuildMedia 3 жыл бұрын
Im not sure. Thanks for checking out the video, dont forget to subscribe
@CookedRigatoni1 2 жыл бұрын
How did u seal it, no water got in after a while?
@1BuildMedia 2 жыл бұрын
I used the expoxy to seal the edges no water gets in the ligt its been 2 years and counting
@kevovq3727 Жыл бұрын
Do u have to seal hole where wires come out????
@1BuildMedia Жыл бұрын
No
@TrustMyStyle Жыл бұрын
90mm and 120mm Should work fine right? what you think?
@1BuildMedia Жыл бұрын
I think those should be okay
@44w23 3 жыл бұрын
Do you need to buy 2 pairs of the halos?
@1BuildMedia 3 жыл бұрын
You need 1 pair of both sizes
@chasebandz7083 2 жыл бұрын
Any links for the halo rings
@1BuildMedia 2 жыл бұрын
see description
@alejandroalvarez6268 3 жыл бұрын
Can someone help me out, I did mine but my won’t turn on when my lights are on they will blink n turn on when break
@1BuildMedia 3 жыл бұрын
look at my pinned comments for wiring info
@alejandroalvarez6268 3 жыл бұрын
I did but now when I turn my left blinker they both off
@1BuildMedia 3 жыл бұрын
Did you figure this out?
@Samy-fk5tg 3 жыл бұрын
What about that trunk part, is it doable as well!?
@1BuildMedia 3 жыл бұрын
What do you mean? the only thing I did post video was to wrap it so it matches the look of the other lights.
@g37x-modsandclips37 3 жыл бұрын
@@1BuildMedia i think he meant doable as if the trunk light was solid too and matched, not little red dots that makes it the break trunk light
@1BuildMedia 3 жыл бұрын
@@g37x-modsandclips37 Haaa I see what you mean. The trunk lights dont light up with the break lights. they only house the reverse lights in a non red section that illuminates when in reverse. I hope this answers the question @s. galarneau
@clonehd6510 2 жыл бұрын
So I have to pay $170 in total? Anyway I can find halos for cheaper or nah.
@1BuildMedia 2 жыл бұрын
You can. But I went with a reputable brand.
@GoofysBandit 3 жыл бұрын
Dang the 90mm are on back order for like two months...
@swanknasty2527 3 жыл бұрын
Lmao same, just got mine & doin em this weekend tho!
@Caleb____ Жыл бұрын
What gauge wire do you use?
@1BuildMedia Жыл бұрын
Im not sure I understand the question all the wires cames with the halos.
@stevenvlogss8505 2 жыл бұрын
so 220$ for basically gtr tailights
@glocktv2411 2 жыл бұрын
Does this work on g35?
@1BuildMedia 2 жыл бұрын
I'm not sure. You got to go to the site and find out
@Stock.Foreign Жыл бұрын
from the taillights
@espy56 2 жыл бұрын
Hey I did this project and when the halos are at low brightness (like when you turn your headlights on) the LED driver box makes a very high pitch ringing noise, audible from the cabin. But when I press on the breaks and the halos go to a more intense brightness the ringing noise stops until it returns to normal brightness. Any thoughts on this noise?
@1BuildMedia 2 жыл бұрын
What kind of radio? Stock or android?
@espy56 2 жыл бұрын
@@1BuildMedia stock, and I know it was coming from the LED driver for the halos, I held it up to my ear.
@1BuildMedia 2 жыл бұрын
Took a minute to find this link. I had the same issue but I have the Android radio. It was so bad I put my stock radio in and all of that went away. That wasnt permanent as I wanted to put my Tesla screen back in. I ended up purchasing this device which pulls power directly from the battery: www.diodedynamics.com/switchback-solid-state-relay-harness-pair.html You will have to do this at your own risk. I have no videos of it nor do i remember how to install it. Also you should double check your wires as it could be a grounding problem. Like I said I had no issues when this was paired with the stock radio, then again I had a subscriber that did both his headlights and swapped the radio and had no issues whatsoever.
@user-fs4ci9yr4d 3 жыл бұрын
Видео крутое но был бы перевод цены не было бы
@moktarmalik1174 3 жыл бұрын
How much did the parts cost you?
@1BuildMedia 3 жыл бұрын
$280 I had most of the tools already.
@joeldiaz615 3 жыл бұрын
Does the paint affect the reflector at all?
@1BuildMedia 3 жыл бұрын
No not even a little bit
@joeldiaz615 3 жыл бұрын
What about the side leds? Did you do anything to those or just sprayed over it?
@1BuildMedia 2 жыл бұрын
@@joeldiaz615 I sprayed everything. only thing you see are two halos. see my ig @g37supreme
@jamesfarley4504 Жыл бұрын
Would you do this for money? Looks like too much work for me!
@1BuildMedia Жыл бұрын
I have thought about it. I am not there yet. alot of guys do it, you can find them on IG.
@mannygee5111 3 жыл бұрын
What’s that tool called that you’re using to open the lights up?
@1BuildMedia 3 жыл бұрын
Rotary tool or dremel. Link in description.
@moktarmalik1174 3 жыл бұрын
Would a 90 and 100 work?
@1BuildMedia 3 жыл бұрын
It would yes
@davidgarcia9681 Жыл бұрын
Do you have to spray paint them?
@1BuildMedia Жыл бұрын
see full video.
@davidgarcia9681 Жыл бұрын
@@1BuildMedia yea I know you did but do you have to?
@1BuildMedia Жыл бұрын
You don't have to but I'm not sure how it will look with the chrome when it's illuminated
@davidgarcia9681 Жыл бұрын
@@1BuildMedia just finished them I left them chrome still looks good though only because you just kind of see the reflection of the bottom but still look kind of the same thanks a lot for the tutorial saved a couple hundred bucks
@manuelpena8714 2 ай бұрын
You know you didn’t have too use a dremal you could of used a heat gun too take them apart
@thatdallastx7861 Жыл бұрын
Can u do mine
@1BuildMedia Жыл бұрын
I dont
@Bri11ante 3 жыл бұрын
Bro what about us 1st gens 🤔
@1BuildMedia 3 жыл бұрын
sorry man I could only work on what I have, I am sure some of it is applicable to you.
@sanzonamckillit3763 3 жыл бұрын
I can build you some! Check out my work on Instagram @sandiego.retrofit
@Blinx777 3 жыл бұрын
Can I pay someone to do these for mine?
@1BuildMedia 3 жыл бұрын
You can send me a dm on Instagram @g37supreme we can talk there
@Blinx777 3 жыл бұрын
@@1BuildMedia I have a g37 ipl coupe. Would it still work?
@1BuildMedia 3 жыл бұрын
The same method applies
@DJKIDWU 3 жыл бұрын
876lifestyle
@1BuildMedia 3 жыл бұрын
--------------------------------- Wiring Configuration ------------------------------- Factory to DIODE DYNAMICS Black to BLACK Green with yellow strip to YELLOW Green with white stripe to WHITE Green to RED ------------------------------------------------------------------------------------------------- -------------------------------------------------------------------------------------------------- IG: @g37supreme Car Club: @876ix.lifestyle -----------------Affiliate links------------------- ------------Items you will need-------------- 1. Rotary tool Wired: amzn.to/3zyRjmW 1a. Rotary Tool Wireless: amzn.to/3vFjShI 2. Diamond Cutting wheel: amzn.to/3zsjPqp 3. Tail as turn module: amzn.to/3zndH2M 4. Rust-Oleum Primer: amzn.to/3vBxrOU 5. Rust-Oleum Gloss Black: amzn.to/3OShFWJ 6. JB Weld Clear Weld Quick Setting Epoxy, 2 packs: amzn.to/3JqILTY 7. Tarnish Resistant Silver Wire: amzn.to/3oQzU4j 8. Diode Dynamics 110mm halos with red driver: amzn.to/3Ql7tHl 9. Diode Dynamics 90mm halos with red driver: bit.ly/3vDOkZl 10. Diode Dynamics 90 and 120 red 4 pack: amzn.to/3vDCKxw
Vehicle Freak
Рет қаралды 93 М.
VIK7ORIO's Workshop
Рет қаралды 1,4 М.
Workshop 12
Рет қаралды 24 М.
BMW GSA 1250
Рет қаралды 7 МЛН
Автосалон Синдиката
Рет қаралды 1,1 МЛН