I need your help

Where

I need a screen, home button and rear glass… How much will all that cost, Namibia $….?

Thank you

Thank you!

That's great! thanks

Thank you that's great to hear!

For how much you got the new screen if I may ask?

yes I would like to know too. As I assume your from the Uk?

Thank you

Thank you

What adhesive did u use?

@@tylerwonderz4933 here is some pre-cut adhesive for that model amzn.to/2VChKGE and for the rear glass amzn.to/2Vbjlnu

Thank you!

Thank you

Thank you too!

Thanks

iFixit.com sell them also eBay or Amazon

Try Ebay or Amazon. No loca glue is not used for this type of repair. I would not do glass only repair on this model.

.

there are another videos that explain how to replace only the glass and this item is much less expensive then the whole screen

What's holding you back?

I have two broken ones and wish I had some tools to fix them :(

Try these 5mm amzn.to/2XneOw3 and 2mm amzn.to/2rOmhbA

It is very difficult to do glass only repair by hand. A heat gun or hot air station will more likely cause heat damage to the display. Otherwise with the proper expensive equipment it is not impossible just not practical for one repair.

Oh dear lord I think you Fkd up but you can redeem your self. Yes you can buy a donor to help you out.

Well if the screen is cracked then water resistance is already compromised and physical damage is not covered under the manufacturers warranty.

It just depends on what you want to do. "Glass Only" repair is difficult, time consuming and not very practical. It is up to you.

@@FixItPlanet1 Well, all I want is a new screen without spending 250E. when my phone costed me 650E. 2,5 years ago. This looks indeed less hassle free.

Replace the whole screen

Most are all the same with a few exceptions but not like the iPhone

If it is done properly it will be fine better than a cracked screen but would not pass factory spec..

I would not recommend using any kind of liquid glue.

Fix It Planet in time, the adhesive does not peel off?

Lololol

Varies depending on temp, distance, preheating, etc.

You could but it will take longer to heat up.

You can get different widths here amzn.to/3nBoX5m

At this time we are not a parts re-seller. We do sell some accessories and a few tools but pretty limited. Our primary focus is on repairs. We may decide to expand what we sell in the future but not yet. That display is very expensive (the glass only is cheap but requires more labor, UV glue, special tools etc.)

Cut to fit and apply where needed, or you can buy pre-cut adhesive.

Maybe

Yes..I did use a hair dryer for the removal of the "back glass"..(note, Not the Front!!!)...the hair dryer, was on high...for about 45 secs...as i moved around the back edges..focused around the edges..You do not want to heat the inside..like the battery or the touch pad area.....I felt the back layer, with my fingers..I.e the temperature is just "hot" enough to be able to hold...as i pry open..using a PLASTIC pry tool...(Not Metal..as i didnt want to SHORT any electrical connections like on the mother board!!... i didnt allow the edge- layers to stick back again by inserting a plastic card, or guitar pick, all around the edges...Dont force the layers apart!!! with too much force..as the back glass is flimsy and cracks easily..(i can only guess the reason it is glass is because the wireless charger may need that and not metal etc..just a guess..but inwould have used thin plastic...but than i dont know specifics. so pull and pry just enough for the Back layer to be moved away. So heat and pry ..and repeat..be patient and slow work helps. Do not push the pry tool too far in...although there is no great danger like in S9 where a ribbon cable connector is in the way...especially at the top..around the camera lens areas..SO start from bottom corners...so again slow work around the edge...Not much glue in the centre. When finished and you are replacing the back layer , if not cracked..or if slightly cracked...you can alays use some stickyvtaoe etc to strengthen the inside ...as a nice back civer later will cover it anyaway!! You may want to buy a sticker sheet ...instead of using a glue tube...A sticker layer specific for the model to stick the back layer..glue sticker sells online for about $2...and back glass layer cab be about $5. The Challenge is the front...and my guess why the phone needs to taken apart to change just the glass layer (high difficulty)...is most likely because of the heat that needs to be used...and we do not want the logic board and other components from being heated. Of course if you think you can...like in some videos go ahead. But if you replace the LCD display WITH frame it's a lot easier...but slightly more expensive. Most replacement I see are from canibalised sets...which means they cab fail soon...I have seen a different OEM displays that maybe better or slightly less brighter..by some manufacturers...and I prefer the new ones.but I guess older models don't make commercial sense for OEM manufacturers to produce...unless it's iPhone screens that seem to have more demand...Not Androids..SO..cheaper phones have more cheaper spare parts..but for a shorter time...and replacement costs are more than the phone..which is crazy..frustrating...but I guess that's life!!!

If the screen is damaged you already lost water resistance. It will never be as good as a factory seal, but you can get the original adhesive strips and if you do a good job it will be better that when it was damaged.

Fix It Planet thanks man

Full screen

Not really.

Unfortunately not. Entire display needs to be replaced. Glass only repair is also very unlikely.

my digitizer is perfectly fine and working only the upper glass is slightly broken I already purchased th8 front glass panel and seen many videos of glass only replacement by removing just the front glass and then sticking the new one on it would you recommend me of doing so

No but have fun and good luck.

Were you able to successfully swap out the glass screen? My screen is cracked but the image is fine and it responds to all commands so I think my digitizer is fine. I dont want to take my phone apart yet if i need to order the digitizer first.

I tried and it failed so i bought a whole new screen.

Too much

Here are some without the frame amzn.to/2IGqJ3h here are some with the frame amzn.to/2GxK6rV

I'm not wasting my time but you go right ahead.

Fix It Planet I'm confused now. Can the repair be done for the front glass only?

$200, I can't find an OEM class "A" for less than $260 . I'm not into the Chinese-ium knock off class "B" and "C" screens.

Go with ebay. I got my lcd and digitizer in an auction for $84.

Did it work out for you? (s7 edge lcd and digitizer) I need to buy one too.

It is working so far -which I know cause I tested it with the motherboard and battery I already have. Repair wise, I still haven't removed the broken screen glass on the digitizer I ordered but thankfully, there are several videos that show how to do so. Also, I also bought the replacement glass on Ebay, brand new without paying an arm and a leg. What type of phone do you have that needs repairs?

No it will not be "waterproof"

A new screen should fix.

Search the internet for replacement screen. Try Ebay or Amazon

Among other things, you cannot disconnect or reconnect the display or disconnect the battery without removing the back cover.

You can just replace the damaged button flex.

thank you. I meant to say I tore the cable that connects the flex buttons to the USB charger. I guess I have to buy the entire USB assembly right?

Yes?

IKR Oh the humanity!

Damn what are we gonna do now

What is this one saying

I repaired the phone

replacement of parts to make a unit work is still a REPAIR.

You’ve titled it a screen repair. You haven’t repaired it. You have replaced it