Garden Tractor Ground Ripper Cultivator Attachment Build
Рет қаралды 580,942
Күн бұрынIn this video I build a Ground Ripper/Cultivator attachment for my Ingersoll 4118 Cat 0 3 point hitch.
For IST Brand Parts for your Old Kohler K Series Engines visit:
www.isavetractors.com
PSA: In this video you see a bad habit I had. I would not take the extra time to move my can of anti-spatter spray further away from me before welding. The contents are non-flammable but are still under pressure so there is always a risk of an explosion occurring. I am aware of this mistake and have made an effort to slow down and move the can away before going back to welding. Enjoy the video but please don't pick up this bad habit yourself. Weld Safe and thank you for saving the tractors!
@garyelderman8391 7 жыл бұрын
Neatly done and a ton less expensive than a disc. Picked up a lot of good info .Thanks.
@bobpaulino4714 5 жыл бұрын
To Isavetractors, Very nice build. It's wonderful to see a younger individual with passion and drive (instead of addicted to all of the electronics). I have a number of older tractors. Wish I had more free time for creativity and tinkering. Keep dreaming! Blessings on your future endeavors.
@sparky72 2 жыл бұрын
Finally getting around to watching this one; just about all the way through the channel! Hope you and your family & farm have been doing well.
@otisdebraburns8539 4 жыл бұрын
I recently discovered your channel and I really enjoy each episode
@Laffy1345 6 жыл бұрын
Norman, great idea. I use to weld with tennis shoes, but I got tired of burning my feet, and I wear jeans, a welding jacket, hat burned my scalp alot. Can't blame my bald spot on that.😂😂😂 Subscribed for more.
@Isavetractors 6 жыл бұрын
Yea, I have burned up one pair of shoes so far. I stopped wearing my steel toe work boots because bending over with the boots up would hurt my toes. I need to order soft toe boots! I wear Arm protectors now.
@Laffy1345 6 жыл бұрын
isavetractors your tuffer than me😒🍺
@011CJ 5 жыл бұрын
That worked realy well another job done with pride
@tonysantana1493 6 жыл бұрын
Awesome job I think I'll have to make one. You do great work Thanks for the video !!!!
@JohnMarionDotCom 3 жыл бұрын
Great video. I attached a Titan ripper on my 1993 Craftsman garden tractor using a sleeve hitch from Johnny Products.
@steiger256 8 жыл бұрын
cool videos. I am in the process of getting my shop going. I can't wait to start fabricating And restoring my old garden tractors. You seem very knowledgeable on w h at you do. Love watching And learning new tricks. Thanks again for your videos.
@Isavetractors 8 жыл бұрын
You're welcome and thank you for the kind words! I have videos coming out weekly now so stay tuned. When you need parts for your old small engines think of isavetractors.com
@paulg444 3 жыл бұрын
He is such a great guy!!.. I wish he lived next door to me!
@mrbrown3546 3 жыл бұрын
Nice job, a little wider would've made it perfect, won't be driving over what you've just done and less passes ...but still a good job. Little tip for drilling, don't go straight to a large drill bit, step it from smaller sizes, your drill bits will last longer. Also if it's smoking like it did it's getting too hot, over heating drill bits will wreck them fast, you need some coolant/lubricant on there. I've seen people use many things in a pinch 😉
@yorkwilson4367 5 жыл бұрын
Great job. You've inspired me to give it a shot.
@Isavetractors 5 жыл бұрын
You comment is the kind I like the most!
@shawngleason1345 7 жыл бұрын
Enjoyed your video, great project. P.S. That Clean Weld spray is meant to be sprayed inside welder nozzle it prevents slag from building up on the tip.
@zack7699 8 жыл бұрын
Nice work... Love that tractor too!
@alphaone101 7 жыл бұрын
Very nicely done Norman. The only thing more that I would have done was round off all the sharp corners which I seem to always manage to find a way to tear my jeans or cut my leg on! I purchased a new utility trailer a couple of years ago and when I got it home I spent probably an hour so with the angle grinder rounding off the 90 degree corners all over the trailer and touching up the paint. I use a quarter (coin) and a scribe to mark the radius on the corners and that way when I grind them off they're all the same radius!
@Isavetractors 7 жыл бұрын
Thanks for your comment, I agree, I should have taken off more sharp corners. Truth is I did this project on a whim to handle a problem on my property,, and decided to film it. I did not expect to get this much interest on this video!
@davidelo5843 7 жыл бұрын
Great video ! High quality build !
@jason-white 8 жыл бұрын
Keep it up Norman, I am REALLY!!!!!! enjoying your videos. I hope to build half the stuff you do some day.
@Isavetractors 8 жыл бұрын
Thank you for the kind words!
@GreenAcreHomestead 8 жыл бұрын
@5:28 just curious why you chose not to use your new chop saw. Was it because the piece is small and hard to clamp in, or was it too big for the cut?
@Isavetractors 8 жыл бұрын
it would not clamp well in the chop saw because of its short length.
@briggsmedia 7 жыл бұрын
Excellent job!
@robpond7385 5 жыл бұрын
norm i am hoping to build fel on my 446 case onan motor hyd love the old tractors after learning from you
@davidcurry6444 7 жыл бұрын
Let the blade do the cutting, don't force it through, great job...
@1941pearl 7 жыл бұрын
Excellent build there friend!
@LordCarpenter 3 жыл бұрын
Nicely done!
@cordellrush9806 8 жыл бұрын
very nice quality work
@IHcubcadet 7 жыл бұрын
Nice job! That came out great!
@chuckcole2200 7 жыл бұрын
IHcubcadet
@robertdavis6708 7 жыл бұрын
I save Wheel Horses too. You do good work. Congratulations on a successful build. Keep saving them, as many people don't understand our passions or sicknesses. lol. Cheers.
@Isavetractors 7 жыл бұрын
Thanks for your kind comment! I appreciate it!
@mahavirmukati6523 7 жыл бұрын
Robert Davis
@AlfredoPerez-fq2yp 6 жыл бұрын
Robert Davis OKok u
@jeffscomments1865 5 жыл бұрын
Awesome build and works great. Word to the wise, when you use the angle grinder for cutting, wear thick welding gloves cuz when it kicks (not if) you will be missing a finger in a jiffy.
@funkidslearning9646 3 жыл бұрын
That looks great... I do 5 acre farm and I looking for a mini tractor to clean weeds between places of rows..
@zbigniewteterycz1571 2 жыл бұрын
SUPER IDEA . POZDRAWIAM .
@compacttractortv5074 5 жыл бұрын
very nicely done
@jbshomestead7694 7 жыл бұрын
great job, I messed my cannon camera up by recording my friend weld on my horse trailor
@Isavetractors 7 жыл бұрын
J&B's Homestead I use a lens cover to protect the camera lens. but I do have to replace the lens cover after a while. it will catch spatter
@trdavis55 4 жыл бұрын
NIce! Would like one to recondition my gravel driveway...
@CaptRuss1 7 жыл бұрын
Nice job
@homesteadspirit9209 8 жыл бұрын
you should have yourself a big old garden. you have a whole line of garden tractors. you would be set!
@tykellerman6384 Жыл бұрын
Great job🤠👍
@jajaid6 5 жыл бұрын
what type of blade is that?cut through the metal so easily!!
@johnturgeon979 4 жыл бұрын
I noticed on a couple of your videos you use flux core wire do you like that better than using gas and bare wire?
@karlbuschtoolmaker 7 жыл бұрын
Nice injuneering hats off
@1amelka 5 жыл бұрын
Nice spelling! LOL
@hermayneMUNSTER 4 жыл бұрын
Hey Norman, long time listener first time caller. Starting to get into welding myself and picked up a multiprocess welder to dabble in all the disciplines. With your flux core builds, any issues with welds breaking or welds not holding up compared to stick welds? I enjoy the content, keep it up!
@nariyabangali9814 3 жыл бұрын
Good tractor !
@roberthowland4503 5 жыл бұрын
Good job
@PullStartStables 4 жыл бұрын
Norman, cool video! I am contemplating some type of ripper or even a tiller on the back of a Wheel Horse C-161-8 / Ark Loader I am picking up soon. I know I need weight behind me for loader ballast, but I’d like to tear up soil and scrape it off with the same piece of equipment.
@Isavetractors 4 жыл бұрын
It's a good idea. You can use a fixed weight bracket that is separate from your implement lift, so you can have both ballast and a ripper. You should also install ripper teeth onto your bucket and use it for both ripping and scooping
@PullStartStables 4 жыл бұрын
isavetractors good ideas as well! I have yet to see the machine but have an agreement with the current owner. It’s not really on the market. Once I pick it up, I’ll figure out how to make it all work for me!
@canifixit3504 2 жыл бұрын
Hey im working on a simplicity 9029 i need a bering for the forward revers lever where can i get one
@hallaabin5637 7 жыл бұрын
Terima kasih banyak .....
@meandthemrs7403 8 ай бұрын
Why were you running the chop saw with a generator? Testing the generator?
@negativefishermen9286 7 жыл бұрын
should have made it longer. its narrower then the tractor so you cant make passes without running over what you just broke up
@mrbrown3546 3 жыл бұрын
Just two extra blades would've worked well, plus a little extra weight at the back wouldn't hurt when ripping.
@robpond7385 5 жыл бұрын
1 am 66 never to old to learn ty norm
@JasonTate86 5 жыл бұрын
You do awesome work, I am going to be looking for a k series rebuild kit for a 12 hp 301. Do you sell complete kits with new cams ?
@Isavetractors 5 жыл бұрын
We sell complete rebuild kits. Check out our website. we dont sell cams. If your cam is not broken. Reuse it.
@funkidslearning9646 3 жыл бұрын
How wide for both tires are from left to right?
@MrVailtown 7 жыл бұрын
Is that welder engine driven ? And is it a comb unit, stick/mig, AC/DC and what brand/Model please ?
@Isavetractors 7 жыл бұрын
It's just a 140 AMP inverter wire/mig welder. I run it off of a 3650 watt portable generator. Nothing fancy. It's a Klutch 140si welder.
@ChrisSingleton299 5 жыл бұрын
just wondering what size generator are you us to power your welder, an if you ever want a tougher paint try Magic Paint its sold at tractor supply the only bad about it is it take 24 hours to dry but when it does its almost like powder coating
@Isavetractors 5 жыл бұрын
Back then I think I had a 4000 watt generator. I no longer use a generator to power my welders but it worked back then. Thanks for watching!
@mikegill4471 4 жыл бұрын
Did you make the scarifying teeth or buy them?
@umerbilal2909 3 жыл бұрын
Hi dear could you inform me where from I can get this kind of tractor
@NilsKall 8 жыл бұрын
Nice video! I like how you explain what and why you do stuff. I didn't really hear what you said about the spray you are using(my native language is Swedish). Are you using a no gas welder and the spray is to keep the splatter to attach to the steel? I have a no gas welder to and will soon be using it to build a new mower deck for my 28 year old Stiga Park. That tip could be useful then. Regards Nils from Sweden.
@Isavetractors 8 жыл бұрын
Hi Nils, yes the spray is a keep the spatter from sticking. It's called Kleen Weld. It works great!
@1941pearl 7 жыл бұрын
Norman, do you or could you build those Ground Rippers for a 3 point hitch 2510 Kioti, 50 in wide with five tines?
@Isavetractors 7 жыл бұрын
Hi Ken, I could build one for a 3 point hitch, but I am not currently set up to cost effectively manufacturer any attachments for customers. Maybe in the future. Thanks for watching!
@chopperhedduck 6 жыл бұрын
Nice design, good work. I see a few similarities to my setup.What did you use for shanks? Were they store bought? You should have stuck with your original width, or possibly gone wider. Can you gear down and go deeper?
@Isavetractors 6 жыл бұрын
The shanks are from Agri Supply. In the video I test it digging it in pure compacted sand and gravel. It works much better in our garden area which is a nice loamy top soil.
@charleschapman2428 7 жыл бұрын
Add Gypsum to the soil it helps break it up along with some Organics . It will take a few application's, you don't have to till it in.
@GeorgeMcIntyre-jw2jr Жыл бұрын
Do you sale part's for a Allis chalmer 611 I'm looking for a carburetor and looking for and brake pads and also parts for a mower
@conley_v5848 8 ай бұрын
What size are the tines?
@funkidslearning9646 3 жыл бұрын
How can I buy a minn tiller which can clean weeds like that and what the price is...! ? I like a mini one with 5 acre farm
@davidshowalter2537 8 жыл бұрын
nice man i built one about like it for a wheel horse goes on where the mower deck was about like a grader blade does OK
@Isavetractors 8 жыл бұрын
Very cool! Would love to see it some day!
@davidshowalter2537 8 жыл бұрын
I don't have a picture on my phone but I will get one and send it to you
@DKTractors 8 жыл бұрын
Awesome job I'd recommend getting a large shop fan to blow the welding smoke away from you. Cheaper then a fume extractor or hospital bills :)
@Isavetractors 8 жыл бұрын
Thanks! I do have a box fan running off camera, but I could use a stronger one for sure!
@Isavetractors 8 жыл бұрын
As a result of your suggestion I am going to buy a pedestal shop fan today at Harbor Frieght! I rewatched the video and even with my fan, that welding smoke comes right at me
@DKTractors 8 жыл бұрын
Yeah the commercial floor fans are good for keeping mosquitos away too!
@DKTractors 8 жыл бұрын
+isavetractors just read your article in LATMag nicely done keep the articles coming!
@stuartluig2911 3 жыл бұрын
Great video and effort but it’s not actually braking up the hardpan, it’s just scratching the top of it and making more layers of compaction.
@JC-hp3cx 3 жыл бұрын
What is the model name and number of the 🚜 you use please I like the size of it and how much?
@akaeldin 7 жыл бұрын
just two things that i have noticed that needs some work on one is not to have your spray can that close to your welding a hot spark could explode your can and if you got closer to your weld about 1/4 inch away from your material you should have less splatter. at 378 on time line looks like you are over an inch away with your nozzle.
@popsknows5648 7 жыл бұрын
akaeldin yes ive seen one explode in the shop. serious injury and burns.
@GreatnPwrfulSteve 4 жыл бұрын
Every time he says “here I am” you must take a shot.
@davidvickers8425 3 жыл бұрын
Lol i was going to say "and here i am, commenting...."
@owentimo 5 жыл бұрын
AMAZING job, what brand was that saw? I need one.
@maggs131 4 жыл бұрын
Listen to the video he says its name clearly
@bradenhollander4491 4 жыл бұрын
I have an Ingersoll two and a 112 John Deere lawnmower
@kylerzonca1875 6 жыл бұрын
If you were located in tx i would pay you to get my 49 ford 8n and bolens 1050 to run lol
@sharavinv4586 6 жыл бұрын
can u describe about the actual material(steel or iron type) used?
@Isavetractors 6 жыл бұрын
Regular Hot Rolled Mild Steel from a local steel supplier
@157dixon 7 жыл бұрын
Good businessman
@justinwolford1087 6 жыл бұрын
Soft dirt , or is it sand ? Do you think it will work in harder dirt / rock ?
@Isavetractors 6 жыл бұрын
Our property is mostly sand. I think it will work with denser material, but you would have to make multiple light cuts. It works well in our garden with well amended soil.
@kimutairop2847 6 жыл бұрын
Does the "A" attachment come with the hydraulic to lift it. What drives the hydraulic pump?
@Isavetractors 6 жыл бұрын
The "A" Frame is a separate attachment for the 3 point lift. The engine drives a hydraulic gear pump that drives the entire drive train of the tractor.
@GodofAbraham 3 жыл бұрын
You sir are a bad man welding in shorts I tried it once and nearly died.
@dougshaw9701 3 жыл бұрын
if i had any welding skills i would build one also for my LS tractor...but i suck at welding
@Isavetractors 3 жыл бұрын
Only 1 way to get better. Do it!
@denniswable3116 6 жыл бұрын
You should sell them... I myself would by one, honestly in need of one
@lloydjohnston9348 6 жыл бұрын
I have been using kitchen spray it is called {PAM }here in Canada mucher cheaper
@Dc-po7zt 8 жыл бұрын
do you have any simplicitys?
@Isavetractors 8 жыл бұрын
I have an Allis Chalmers B1, that's the closest tractor I have to a Simplicity. (They were the same company at one time)
@wahouakha8308 5 жыл бұрын
I need to buy one now let me know
@Isavetractors 5 жыл бұрын
seach Facebook Marketplace
@ThePadutch 3 жыл бұрын
Welding in shorts Norm, I'm surprised your legs don't look like you've escaped from a leper colony ... lol I've burnt holes right through my leather boots with hot slag from my mig ...
@johnfarmall127 7 жыл бұрын
I got a case 448
@znovosad555 6 жыл бұрын
Hmh. Maybe a grader blade isn't what I need at all for what I want to do. A ripping bar or box blade with ripping teeth might be what I need initially.
@Isavetractors 6 жыл бұрын
You will find you will end up buying/building a lot of implements. Not only is it a lot of fun, sometimes you just need a custom tool
@znovosad555 6 жыл бұрын
isavetractors that's very true. I'll probably end up getting a grader shortly after the box blade with a ripping bar haha
@lloydjohnston9348 6 жыл бұрын
cooking oil in a spray can does a great job and is very cheep try it
@socorrocalzada2534 6 жыл бұрын
What is the number of horsepower the tractor has?
@Isavetractors 6 жыл бұрын
18HP
@Isavetractors 6 жыл бұрын
Onan P218
@socorrocalzada2534 6 жыл бұрын
Ok mine has 12 and also you REPLIED!? You are a very cool and talented person and I love your videos!
@armandolanda5082 6 жыл бұрын
That was my question, I am totally wowed! Amazing!
@seansysig 7 жыл бұрын
Do yourself a big favor, get a welding jacket to protect your skin from harmful UV rays from the welding arc! Melanoma (Cancer) is escalated by UV. Also a particulate mask to protect your lungs.
@Isavetractors 7 жыл бұрын
Thanks for looking out!
@rohanduvenage8459 5 жыл бұрын
Get a life..
@biggetl1319 7 жыл бұрын
Who welded that? Ray Charles!
@kartsandcameras2441 7 жыл бұрын
Yep! And probly with his feet!
@s.pursell8901 5 жыл бұрын
It didn't go but two inches in the soil. I like the design but it never proved you can bury the tines 6 inches and rip the hard soil. After all that work and money spent on the metal, it would be cheaper to rent a rear tine tiller for a day if it can only go 2 inches. Seriously I really like your design. Good luck. That Klean Weld is meant to be sprayed inside the tip of your welder nozzle. To prevent buildup of slag from the spray. Not to be applied to the welding seem. That you want to be clean metal on metal. Good luck fella!
@user-ip4gv8wl3g 4 жыл бұрын
I like the vids but... how bout replacing generator noise with music, commentary, or anything else? Good job though
@Isavetractors 4 жыл бұрын
Done! You will see in my later videos I add more commentary. Have a proper welding outlet now too so no more generator noise. Thanks for watching!
@velvetelvis43 4 жыл бұрын
Now here I am.....
@BlueberryStinkFinger62 2 ай бұрын
Is this guy even still alive?
@Isavetractors 2 ай бұрын
The myth is, he is around somewhere saving the tractors...
@fishinginpa4716 6 жыл бұрын
The anti splatter spray is intended for the nozzle of your mig gun ,not the piece you are welding on , just saying save yourself some money that way
@Isavetractors 6 жыл бұрын
Anti Spatter spray is for anything you don't want spatter to stick to. It works great on the metal you're working on. You should try it. I dip my nozzle in an anti spatter gel. I weld with Flux Core Wire so anti spatter spray is a great time saver.
@popsknows5648 7 жыл бұрын
I have seen an aerosol can explode sitting on a welding table. great job just be safe so we can keep seeing your videos.
@Isavetractors 7 жыл бұрын
PT SUTPHIN yea it's a bad habit of mine but the contents are non flammable according to the can but still is under pressure. I have since kicked the habit and you won't see the can in future videos. thanks for watching and for your concern.
@maggs131 4 жыл бұрын
Get rid of that shitty flux core and get a tank of argon. You wont have all that splatter to worry about
@danieldavenport274 Жыл бұрын
I'm not so sure that works great. ... I have planted a money tree in my back yard though.....works great also...
@allenmckinney9533 6 жыл бұрын
I cringe when I see flux core welders used for stuff like that. For thick steel I'd use a stick welder unless I had a good mig setup.
@Isavetractors 6 жыл бұрын
I cringe when I see comments like this. It spreads false information that flux core is not a capable welding process which is untrue. Flux core wire can weld much hotter than gas shielded mig.
@allenmckinney9533 6 жыл бұрын
@@Isavetractors not saying I wouldn't use one but for thick steel I rather use my stick welder. Mig is mainly more convenient but cost more to run. I've been thinking of getting a flux core to do thinner stuff with.
@Isavetractors 6 жыл бұрын
On the contrary I dont like using flux core for the thinner stuff. When I fix the hood on the 4040 I will be getting bottle of gas for it. Check out my JD400 suitcase weight bracket build. I use .035 flux core out of a 200 amp wire welder. Welding 3/8". Keep in mind this Cultivator build is an old video. The suitcase bracket was my most recent welding project. Big difference in the end result.
@allenmckinney9533 6 жыл бұрын
@@Isavetractors ok. I subbed today so I'll check it out. I got my hands on a 89 craftsman gt6000 Onan 20hp with sleeve hitch.
@Isavetractors 6 жыл бұрын
Nice!
@allthegames2013 8 жыл бұрын
Get a valmet if you want a real tractor.
Josh's Green Garage
Рет қаралды 13 М.
isavetractors
Рет қаралды 31 М.
Micro Food Plots
Рет қаралды 708 М.
Lanning Long Arm Mowing LLC
Рет қаралды 84 М.
John Marion
Рет қаралды 48 М.