I really appreciate you taking the time to translate this to English

I've made copper coils out of tubing and if you fill the tubing with sugar or salt before bending it will hold a circular cross section in tight bends as opposed to flattening out or kinking. I use salt or sugar because it packs well (using vibration from an Oral B toothbrush) and can be removed using water after the bend is completed.

If you fill the copper tube with sand first and flatten the ends you bend without worrying it will kink or crush. Really awesome flame from what you have built. what a beast!

It makes me feel all warm and fuzzy inside when he says "health and peace to you and your loved ones" it's a good greeting, I like it

I used cooper tubing before and at higher temperatures corroded inside, and the flakes clogged the burner nozel. Recommend using stainless steel tubing, the best place is brake lines for the car. Cheers the best idea ever

Nice prototype! Looking forward to seeing tested applications of it with more durable materials

that looks like a very effective little heater, thanks!

I can't say that I hold out much hope for the crystal structure of that copper that you're heating to Cherry red (and near the burner to yellow). As a bit of fun it was very impressive - as a heater, I wouldn't go within 20 feet of it.

Mr Robo, I admire your patience in replying to so many of these helpful(?) comments. Well done. And I enjoyed the video. Thanks!

So good to see your videos where you use 'best practices' - Cutting fluid when drilling, good tapping technique. etc. I've seen so many vids where they don't use any lube, and/or just keep cranking the tap/die without ever backing off to clear chips Thanks for posting this.

Ahhh 🙂 I can definitely see great uses for this. I need something like this for the burning of methane and HHO. I wanna make one small with multiple outputs to drive a heat pump system like a steam engine rig, or to run sterling engines.

Love the minimalist design! Ingenious! Health to you and your loved ones. From 🏴󠁧󠁢󠁥󠁮󠁧󠁿

Great work hope your copper will not fail soon. Mine did. Not exactly the same setup but something similar

Genius ! Keep it up . You are on the right side of creativity and success.

Awesome video my friend! Can’t wait for the next one! 👍🏴󠁧󠁢󠁳󠁣󠁴󠁿

Wow wow wow, this is the first on my list of DIY, I am so impressed. As a process operator, seeing this simple burner just makes my day

The reason there's no pressure and why you can't regulate the flame is because the valve is before the coil. If you put a valve after the coil but before it's burnt the pressure will increase according to the valve position. But be careful of the pressure, or it might explode.

The concept is quite similar to the way the Alladin lamps were built in the UK in 1800's. Worked well for them so I think this should work very well as a heater, I think it would be better to have the fuel reserve further from the flame though?

awesome working idea.superb workmanship , very neat & clean - viewer from the Phils.

Very nice idea.. love it..

Honestly surprised the the copper tubing wouldn't melt. Cool vid. Maybe stainless brake tubing, if it would? It will wear your hands out making the coil, but should last longer and take higher heat, but won't transfer heat as good as the copper. Cute dog, cheers.

You can protect that orifice from debris with a copper spun filter drier used in refrigeration systems. Cut it in half and empty out the silica beads, then braze it back together. Super fine mesh metal screen in filter.👍

Very nice setup. Thanks for the knowledge.

It’s beautiful, thank you so much. This kind of knowledge is crucial. 👍

The same principle is used on some camping stoves that work on different fuels. No need to carry propane canisters

Cool idea, one thought though, I’d invest in a good carbon monoxide detector (when operating in closed environments, outside no worries) rule of thumb, if it burns oxygen it creates noxious gases. But, I like it for many uses and I’ve been a HVAC contractor for a hell of a lot longer than I’d care to admit.

This is the best one of these I've seen. You pay great attention to detail, using the lost art of common sense.

This is great, modern old tech is way. With modern manufacturing process and types of material I think some of the old world tech is very applicable to today's world.

Did you like the idea friends?

you now need the copper coil burner to be surrounded with a heat sink, vented brake disks stacked on top of each other with a thick steel lid is what most people use, the radiant heat is much better, and a lot safer than exposed flames, and they look really cool painted up with HTP.

Very cool stuff, thank you and a big LIKE !!!

Fantastic ! Thank s for your video

На внутренней поверхности раскалённой трубки происходит крекинг углеводородов. Если часть образующегося углерода будет формировать механически прочный слой, трубка рано или поздно засорится.

Add afterburner in the form of steel mesh stretching far above from the coil.The flame will get even higher and will burn the rest of the gases that didn't burn when inside the coil or are a product of the inside-coil burn (like CO for example).

I'd like to see the video of you making this again using the input from the comments. A version of this with an adjustable flame would be incredibly valuable.

Отличная идея, надо попробовать когда-то.

este es la verdadera receta de un generador uroboro, esto simboliza realmente el dragon que muerde su propia cola o que la quema. yo estoy seguro, calentar el propio recipiente que contiene el combustible, tambien estoy seguro que los hebreos lograron hacer funcionar esta receta con sus lamparas de aceite, gracias a ellas no se quedaban sin iluminacion, aunque es cierto que emite monoxido constantemente. gracias por el video, maravillosa tu obra, te deseo lo mejor, ojala sigas subiendo contenido asi de bonito.

Great idea but instead of copper I will use heavy duty stainless steel break lines.

I'd like to see it using biodiesel. Nice work man.

wow i love this design, i am gonna try out something similar to this in my garden shed, i will ad a little chimney thou. TANK YOU FOR SHARING

ยอดเยี่ยมไปเลย

This is how a burner on a hot air balloon works. They use LP (propane).

Gracias querido amigo por el vídeo muy bueno !!

And here we have a snow puppy "yoink" 😂 You make some very creative heaters 🔥👍

Great imagine if you could ow make it with stainless steel tubing for greater long term durability. Fantastic work!

put some safety fail safe in there if you can otherwise might go boom if it melts down if possible do a safety check in a blast proof container or safe location make a second device and run it until failure just so you can improve upon the safety and longevity of your device you made

Aí e diferenciado parabéns 👏👏👏👍

Está genial me gustó gracias por la explicacion

Tick workshop- i’d like to see how it was when you get it to operate perfectly for your purposes. It would also be nice to hear about the adjustments that I took to get it to that point. A very interesting experiment. I had something tangentially related in my own mind just this afternoon. So it would have been all the more relating to see this work for you. Thank you for sharing. It takes a particular kind of courage and integrity to show the experiments that don’t turn out exactly the way that a person would like.

When I saw how he picked up the dog I said screw this video. Poor thing was cold

The idea is interesting, and I suppose works well in theory (short term). I don't think it's sustainable to heat copper to such high temperatures for long periods of time though. This will eventually go boom.

Mini jet ingine concept. That helps me understand. Thanks for posting.

Nice work. Be safe. Take care :)

very smart, good job!

Nice :) Thanks!

Sensacional 🔥🚀👏👏👏👏💪🇧🇷

Amazing

We have always had dashounds dad just got a puppy. Love ur projects and workshop. Keep up the good work.

Very cool thanks

Exelente, estoy aprendiendo en ese trabajo y si esta bien exñlicado

Perfect❤❤

I think the heat coil needs to be further from the tank and adjustable nozzle. Maybe also a piece of perforated metal in between for a heat shield.

For people wondering how this works… the same principle is still used in basic self-priming camp stoves, and in other low-tech devices. It can be very effective…. Look up how to make an alcohol stove out of a soda can. As Boy Scouts we made them all the time. Called “penny stoves” because a coin is used to regulate the pressure. 🔥 1. Prime it: Liquid fuel is put into a container that can hold necessary pressure. Then liquid fuel it is heated up by an outside source (like a fire) until it turns into high pressure gas fuel. 2. The new high pressure gas that wants to escape. (it does not explode inside his pipe coil because there is not enough oxygen in there to burn … but if the pressure container failed, there would be a tremendous and dangerous explosion ⚠️) 3. The high pressure gas created now escapes from an orifice of some kind and is ignited by you with a match, or more commonly, by the priming process itself. 4. The burning high pressure gas is now designed in such a way so as to preheat and vaporize its own liquid fuel source independently. …. This is why his big flame needs to blast through his copper coil. It must vaporize the liquid behind it. The whole process creates a cycle of pressure and combustion that will continue on forever, or in reality, until the liquid fuel source is either closed off or is completely consumed.

SHOWING innovating thought excellence!

Very nice. Its informative

Clean and precise work. Great.

Yes I do like it.

Thank you

Well, that looks safe!

Wow thats cool I like it.🥁😎🥁..

Well done.👍👏🌲🙂

Very impressive flame. I would put a one-way valve in the tubing right where you connect the plastic line. Weld, not solder but weld, a Y joint to the one way fitting and install a needle valve to control the fuel feed. Make the rubber fuel line from an automobile duty hose with braided stainless steel covering. I know you are trying to make this on a budget but there are a few safety steps you really should consider.

Interesting design, ik subscribed as you have lots of interesting “ out of the box” type of projects! Thanks for sharing and hope you get lots more subscribers.👍

This is a fantastic unit! Thank you for sharing. I am. a new subscriber.

I’ve seen a lab burner that similar, but meant to be horizontally mounted.

Very interesting, greetings.

Great video

"Even my beast freezes quickly " 😂

Very nice good work

I see why you say 10 turns best. The last two glowing red hot says all the fuel is vaporized and superheated. Is it gravity or vapor pressure fed? I missed that part. Awesome little design I bet LPG like in hot air Baloon burner would work extremely well

Muy interesante desde Chile saludos 😊😮😮😮

Excelente

Adding a one way valve would make it safer, for long term use.

That looks like I could blow glass with that flame! 🔥

I have alcohol stoves that use a similar system But only require 2 loops to function properly.

Good job. And you've managed to survive a mechanical apocalypse..

Well, can it burn oil? i would love to build one of these but i mostly have leftover cooking oil so im not sure if it can work on it or not. thx a lot for sharing this its very useful!

Very smart..nice

lol that was rocketing like crazy.

Excelente para hacer tambien lamparas de noche, gracias por tu aporte

Good working I need this

Doy do you have works performed with mig welding?

If you twist the copper pipe outside a iron tube and just let it stay on, you will get a much longer lifespan out of the copper. Sure it will take a little while longer to heat up, but it will last much longer.

Este está muy bueno

THIS IS COOL,I LIKE IT.

GREAT IDEA sir,i wondered,BUT need some modifications for effective utilization like coil space,heat exchange mechanism,flame control...etc..ALL THE BEST..

The gas tank is tightly closed or it has an air breather to ensure sufficient oil flow supply. If there is no air breather, I believe the tank will have a vacuum effect

A voz é linda, suave, cativante e muito agradável de ouvir. dei like por causa da voz.

Graet video

Nice 😀