GE Frontload Washer Error Codes, Troubleshooting, and How to Test Parts

Рет қаралды 206,156

Күн бұрын

If you own a GE Front Load washing machine, it hides a powerful testing and error code system behind its facade. With a few secret button presses, you can quickly find out what may be ailing your washing machine. In the video, we show you how to access GE Washer Error Codes, GE Washer Test Modes, and other options like the GE Consumer Help Indicators which may randomly appear after you use your washing machine.
Need a part to fix your GE Washer? Let me help you out with that! We carry many Samsung refrigerator parts, and can get many others not listed: oemparts.bens-appliances.com/...
The most frequent item I'm seeing people needing to replace is if it boots up and relay clicks, but won't wash, which is a board replacement.
GFW510 - 550 Board: bens-appliances.com/products/...
GFW650 - 850 and PFW 870-950: bens-appliances.com/products/...
For the unit not spinning, the inverter is the most common replacement on this machine:
Video Timeline: bens-appliances.com/products/...
00:00 - Intro
00:24 - How to Activate GE Washer Error Code Mode
01:24 - List of GE Washer Error Codes
03:02 - How to Enter Service Test Mode to Troubleshoot and Test GE Washer Parts
04:04 - List of Tests and What They Do
06:44 - Consumer Help Indicators and What They Mean
Tools I use in all videos can be found at my Amazon Idea Page: www.amazon.com/shop/bensappli...
Did this video help you out? Send me a tip, and help me make more Appliance Repair videos for people to watch for free!
PayPal: paypal.me/BensappliancesYT?lo...
CashApp: $BenjaminSchlichter
Affiliate Disclosure Form: bit.ly/3oXeu3B
** Links to external websites and parts may result in me receiving a commission on sales.

Пікірлер: 405

@bensappliancesandjunk Ай бұрын

I am getting a LOT of people asking about the control board and other issues, so here's the just-released follow-up video on further diagnosis: kzfaq.info/get/bejne/grB_a6iqm7K9j4E.html

@drod5157 Ай бұрын

Last night, mine started acting up. I left it unplugged for an hour. It's working normal for now. I really appreciate your videos. This washer came with the house I purchased. Otherwise, I would never buy GE appliances.

@johnm3405 11 ай бұрын

Drain impeller was just clogged. Running #7 then 12 confirmed no new drain pump needed. Thanks Ben!

@pushaplane 5 ай бұрын

Thank you very much! This is a vital resource for anyone that has this model.

@scottburt2934 Жыл бұрын

I gott'a tell you this is the best DIY video and it was very easy to understand and carry out. It fixed my fast spin problem

@bensappliancesandjunk Жыл бұрын

Thanks!

@ericklaiber9168 Жыл бұрын

Hi Scott, how did it help fix the actual problem? I did both the slow spin and fast spin tests as shown in this video (which is great, thanks Ben!) and the drum would tumble but do NOTHING on the spin. There were no sounds or other indications like a motor was trying to spin which I think rules out both the motor and belt since the drum moved fine in the tumble portion of the tests. What was your ultimate fix?

@ashleyjenkins171 5 ай бұрын

This was an incredibly helpful video! Thank you for taking the time to make it and, fingers crossed, keep me from needing a technician call!

@mountainousterrain1704 2 жыл бұрын

Great video - very clear!

@charlespowell528 3 ай бұрын

Great video! My wife decided to wash some plush bathroom rugs..the washer stopped spinning, I thought here we go $900 for a new washer, watched the video, seen the pump filter part. “ i never knew what that little door was for” I followed your steps and seen the filter completely gunked and covered with plush rug.. cleaned the filter, tried a load of clothes.. works perfect! Thanks for posting the video! Saved me at least a grand, and i might even get some sugar from the wife! Really appreciate it!

@bensappliancesandjunk 3 ай бұрын

Oh wow! Way to go man!

@garyrottier5132 6 ай бұрын

This video was great, it showed me things to look for and definitely how to open the top. Still having problems with the bleach and fabric softener dispensing

@robertr.4777 14 күн бұрын

Great video! One of the best and most informative videos I have ever found for troubleshooting. Thanks for the attention detail and meticulous way you explained everything.

@teresawelch9276 7 ай бұрын

You are awesome! You help me fix my washing machine!!!! I knew nothing lol!!

@JROrg2009 Жыл бұрын

Good video and Thank You. Need to see about error codes and resetting a 2019 GE GFW series front load unit.

@Luckysamtx 7 ай бұрын

Brilliant, very well done. Saved me a ton of time and a call out. Thank you.

@zramirez5471 3 ай бұрын

Man this was the most helpful home appliance video ive ever seen

@bensappliancesandjunk 3 ай бұрын

Glad it helped!

@Nonya_Business44 Жыл бұрын

Thanks for this video and the others. It saved me tons of money.

@olegreal Жыл бұрын

Thank you for the video

@trentwilliams9752 2 жыл бұрын

Great video and this helped me figure out my issue. One comment, you have to enter the test mode from a blank screen, not from the error code screen. That took me like 20 tries to figure out.

@vimanaboy Жыл бұрын

I followed his instructions exactly (I think!) and it worked for me first try. Just saying, for future viewers.

@stevenmata3539 Жыл бұрын

thats what I did but I never was able to enter the test mode

@michaelerbes7517 Жыл бұрын

@@stevenmata3539 Try turning the unit on, press and hold the "start/pause" button, the navigate to the "self clean" option and then let go. Should put you in the diagnostic mode

@wendyhatcher508 9 ай бұрын

They need to recall this son of a gun!

@wendyhatcher508 9 ай бұрын

What if you cant enter troubleshooting mode?

@jhrobinson2000 Жыл бұрын

Great video, do you have the link to the technical service manual?

@lam2018 Жыл бұрын

Great video, thank you for your efforts 👍

@abrahammiron8319 2 жыл бұрын

Great video!!!

@hsmith9100 11 ай бұрын

Amazing video thank you so much!!!!

@recepcakmak7676 2 жыл бұрын

Thanks for video we use this machine in boat and i have 26 error cod and washer not spinning so how can i use in the boat without oob. thank you very much.

@danhertig9170 Жыл бұрын

Thanks!

@vimanaboy Жыл бұрын

Thank you so much!!! Superb video, helped me understand and fix my issue. Might have saved my marriage 😅

@vimanaboy Жыл бұрын

PS: liked and subbed 👍

@elizabethbarber9518 Жыл бұрын

Would you happen to know or have a diagram/picture of how the hoses from the inlet valve to the dispenser hook up?

@yaoyang907 Жыл бұрын

Hi Ben , thank you for the video. My washer stuck on the washer mode than drained with the humming noise and than system canceled the operation itself. I pulled the error code 18 and ran the test 12 . It seems the water drained just fine. Please help

@synaven6895 9 ай бұрын

Hey Ben! I have the same washer this model. I found the door lock switch was burnt at the coil. I ordered the new one after replacing it the washer tried to started but it fleshed (door🔒) then Door code on the display. I never heard the knock sound. Do you know what wrong with it? Thank you

@shawnlocke5942 Жыл бұрын

This video just saved me a ton of $. It was just a simple filter clean. High tech appliance low tech user!

@Ender_Wiggin03 10 ай бұрын

Video's been great, my washer has several codes, but passes the tests, I've tried unplugging the machine, any way to clear the codes?

@Soprano0913 Жыл бұрын

I love all your videos. Thanks so much for this great info. In looking to buy this model. I noticed some people are displaying videos of a brand new machine used for first or second time making whining noise when spinning.. is this a bearing issue? Or a shipping bolt that had not been removed? If it's bearing why is it failing out if box? Thanks in advance

@bensappliancesandjunk Жыл бұрын

Likely shipping bolts

@scarscar2771 6 ай бұрын

How about the main board service led for late model front loaders? I can’t find a lookup table (it’s not on the wiring diagram mini manual).

@hafeezurrahman1000 2 жыл бұрын

Thanks Ben. I am in the process of selecting which brand appliances to buy for my new home. Wondering which brand or brands you would recommend in terms of least problems and/or easier to do a diy repair. I live in Canada.

@jayalldayism Жыл бұрын

Don’t get GE!!!!

@dregenius 11 ай бұрын

I assume you got appliances and we'd love to hear what you got and how you like them. If anyone else is wondering, pretty much every brand seems to be content with one or more completely unfit-for-purpose appliances... GE's front loaders are pretty awesome, but their top loaders have gearboxes made of chalk and their dishwashers seem to love to melt the wheels off the lower trolley. Frigidaire makes a decent range but couldn't figure out how to reliably make ice in the middle of antarctica and their dishwashers are straight up e-waste. Samsung makes really pretty appliances but they're kinda a gamble on reliability. Bosch is about the only mainstream brand that seems to actually care what they sell, but they also kinda gouge on their fridges for example, which are made by midea IIRC, although Bosch dishwashers are so legendary you should probably get one regardless of what every other appliance is in your house. LG is about the only brand that's reasonably priced, perform well (especially their laundry - LG front loaders are about as legendary as Bosch's dishwashers) and *fairly* reliable - although they've had their share of issues with the linear compressor fridges, they seem to be pretty good these days.

@sheilagriffith2172 2 жыл бұрын

How do I clear the codes once I've corrected the issue? I have so many codes, I'd like to clear it so I know if any of them still need to be addressed. Thank you so much for this video!!

@gohan3rdrift Жыл бұрын

Service/test mode #16. It’s at 5:44 of the video.

@jesslang1 11 ай бұрын

Do you know another way to get he washed into test mode? Pushing start and turning wheel counter clockwise isn’t working:(

@kiheidude 2 ай бұрын

I have a similar GE front load washer. To access the error codes and the test functions, the service sheet says to hold the power button and turn the dial 180 degrees. I found that this requires rotating the dial for 6 cycles as there are 12 cycles on the dial. Other videos say to rotate for 8 clicks, but sometimes it takes two clicks to get to the next cycle. It’s better to count the cycles (including the beginning cycle). Release the power button and all the lights will flash and you will enter into test mode. Just rotate the dial to get to the test you want to use.

@chadfowler2459 8 ай бұрын

Hey Ben, I get a loud screech noise when the cold water is activated and have started receiving incomplete wash cycles with soaked clothes. I've even started getting H20 supply text scrolling. Please help! GE ultra fresh washer only had 3 years.

@donaldchase8837 7 ай бұрын

awesome info presented here and helped me to dig further into my problem. model gfw550ssn1ww. when using test mode #8 to see why softener not draining, water only pours from the upper holes in to detergent area not the softener compartment. all others work as should. hot/cold valve, bleach, pre wash etc. could this be a valve failure?

@focusedfowl8981 11 ай бұрын

Excellent video! I have the same issues as many wit the spin process shutting down within 5 seconds. I replaced the accelerometer which had no effect (despite it being indicated during trouble shooting). Now I am wondering if I should gamble on replacing the inverter or the main board. Apparently, the inverter is no longer made, so the pricing is comparable ($125 for either part). Suggestions as to which part maybe faulty? (Codes: 3, 9, 19, 26, 38, 46, 89)

@wallydesouza1 7 ай бұрын

Started having this problem today. Did u solve it ?

@focusedfowl8981 7 ай бұрын

Yes I did, by replacing the main circuit board (motor driver), don’t bother with the accelerometer as I did. By and by, I had a discussion with the GE repairman who mentioned this is a known issue and he carries 2 spare boards on his truck.

@cfhpanterarulz Ай бұрын

@@focusedfowl8981inverter board you replaced on main board

@mobilediesel 11 ай бұрын

Fantastic video. By chance do you know a way to trigger a longer instant spin without all the foreplay (tumbling)? I understand how to trigger a quick 4-minute spin (test 14) and faster 2-minute spin (test 26) but wanted to just jump immediately to a full spin cycle without all the tumbling. The tumbling is driving me crazy.

@bensappliancesandjunk 11 ай бұрын

I don't think it can logic wise

@Connor-xe6fl 7 ай бұрын

The constant tumbling is irritating! I've never seen a washer have so many balancing issues. I should have gone with Electrolux.

@RK-mx7ix Жыл бұрын

Hi Ben, this is SO helpful!! Thank you. I am measuring constant 30.2v at the drain motor plug. Running the test for the drain pump does not change this voltage. Is this a control board issue?

@brandonwilliams3565 Жыл бұрын

Hi! I know your post is a month old but I had the same thing. I was showing 40v. I traced the schematics to the plug on the main board and the little relay under it was burned up. Waiting on my replacement board.

@cherihenry6213 4 ай бұрын

Same here! Replaced drain pump and when I run a diagnostic for the drain, #12, it does nothing. Where do you get a new board besides from GE?

@carletonmartin7682 7 ай бұрын

I have had an issue with my unit 3 weeks ago that started right after a power outage. Had Technician scheduled to come and look at it. Got up the next morning after running several tests for the bigger part of the night and it worked like nothing had happened. I did say door on the display when I got up the next morning. Open and closed the door and the unit works fine until yesterday. Unit will sometimes fill with water, sometimes will not depending on the cleaning cycle selected. I am thinking a faulty main board, but I could be wrong. Also there was another power interruption yesterday just like the previous time. I don't understand why that would cause these issues. I plan to run some of these tests tomorrow afternoon before work to try and figure out what is causing the issue. Seems like it would be something with the door lock, but it locks every time and won't let me open it before the cycle starts. I am confused by this machine. I will probably never purchase another GE appliance after this. It replaced an 11 year old LG that still worked just had a leaking door gasket. Should have replaced the door gasket and kept the LG. Frustrating for sure. Thanks for the great video. Keep up the good work. Sorry for the long post. Just wondering if anyone has experienced this same issue and if the cause was determined. Machine is barely 2 years old. Ridiculous that it should need service already.

@user-tj8xo6hf7x 7 ай бұрын

Hi my friend!! Do you know where I can get the Inverter Board for GE WASHING MACHINE same model than the vídeo?

@lacondalewis5808 Жыл бұрын

What are your thoughts on using vinegar in your laundry, is it safe for the machine?

@bensappliancesandjunk Жыл бұрын

Yes, very safe

@djosbun Жыл бұрын

My washer was purchased January 2021 and either the motor is dying (high pitch noise during spin cycle) or the belt is no longer in alignment with the pulley.

@kintero27 Жыл бұрын

Not working. Error codes 3, 38, 27, 23, 10, 37 Tried counter clockwise and won’t work. Do I need to unplug and do the counterclockwise?

@dominikslomba 5 ай бұрын

Great video When I test the fabric softener valve I see water coming from bleach side, testing bleach valve also water coming from bleach dispense side…is it just one valve or something isn’t wired correctly? Or dispense lines?

@dominikslomba 4 ай бұрын

Did you ever figure it out? I see the same issue

@tmalley77 3 ай бұрын

i am also having same issue

@captainluke90 2 ай бұрын

My drain pumps not working. I replaced it and tried to run test 12 but nothing happened. Help?

@erikagibson 10 ай бұрын

Hi Ben! My husband and I have really appreciated your videos..Bestbuy geek squad has been a joke. We replaced the main board on this machine (gfw850spn2rs) ourselves with the upgraded oem part successfully after it was failing via door errors and cancelled cycles. However, the dial does not align with the light and more importantly, the bleach dispenser is now full of water after a cycle. Is there a way to correct this?

@ltabarah 3 ай бұрын

Same problem. Likely wrong personality number for program. If you did what i did and set it to 1. Likely you must try another until lights and bleach are fixed

@lindalampton8935 Жыл бұрын

Awesome video, did everything still have a draining issue. replace with new pump went thru tests it failed at the drain pump again.

@nmbr1son64 Жыл бұрын

Did you clear the fault code after replacing the drain pump?

@krysealvaran9522 Жыл бұрын

I have the same issue. And I cleared the code after replacing. Did you ever figure it out?

@nmbr1son64 Жыл бұрын

Make sure the drain hose isn't kinked or has sludge in it. Use a shop vac to pull out any (possible) obstructions.

@aidanalmeida 5 күн бұрын

Can you explain what does door switch do Ben.

@MrKittyfisto 9 ай бұрын

Hi - this video was super helpful! Now im wondering how to clear the error codes once we have figured out what needs attention?

@ohniceness6138 9 ай бұрын

Same here

@skeeterhawk439 8 ай бұрын

Same here

@mikvadesigner Жыл бұрын

do you have a text or pdf of the diagnostic info page?

@BrokeBoysOutdoors Жыл бұрын

How do I reset the codes? I have fixed the switch for the door and it still calls a door code

@ashleymesser7547 Жыл бұрын

I got the codes and ran tests 10 and 14. 14 did what it was supposed to do and shut off. 10 wouldn’t do anything after filling up with water. Not sure what to do any help is appreciated. It won’t go through any cycles.

@graphixguy3128 Жыл бұрын

Ben, AWESOME video which sheds light on how technology has changed.... I have the same machine, I have found several error codes. I can't get the same result as you do on entering TEST MODE. Need more detailed info on how to get there.... When I hold the button down and begin spinning the dial, it automatically displays the various wash modes, as in normal cycle... HELP

@JacksonvilleJane-hi1cd Жыл бұрын

I’m having the same issue - not able to enter the service mode at all.

@bretmarrs4590 Жыл бұрын

Once you hold the start button down and rotate the dial 180, you just let go of the start button and it should start flashing. From there just spin the dial to what ever test number you want.

@graphixguy3128 Жыл бұрын

@@bretmarrs4590 Strangest thing, the errors I was getting pointed to the "hall sensor" , which on this model is built onto the motor. Technician came out and did a "firmware upgrade" and all seems to be working fine.... What's your opinion on this?

@michaelerbes7517 Жыл бұрын

@@graphixguy3128 Try turning the unit on, press and hold the "start/pause" button, the navigate to the "self clean" option and then let go. Should put you in the diagnostic mode

@nalbertgerber9930 11 ай бұрын

Power has to be off when starting this. Yes it will cycle thru the modes as you turn the dial but it needs to be off at the beginning

@SirLucidThoughts 6 ай бұрын

Thank you for this video. Someone has been slamming the door and now it has issues

@adriangonsalez3425 2 жыл бұрын

Well done video! I'm close to pinpointing the issue with my Washer. I am getting code 91. Not sure what might be triggering that. We just replaced the motherboard because it wouldn't even allow us to start a wash cycle. The motherboard replacement solved that issue but now the dial does not match up with all the cycles, and getting that code #91. Any help is greatly appreciated!. Again thank you for the great video!

@MilTan2 Жыл бұрын

Just chiming in to say that this video helped me get my washer mostly working again -- thanks! But I'm also getting the issue where the dial doesn't match up, and error code 91...

@801_md Жыл бұрын

@@MilTan2 The same control board is used in different washer models. You will need to set the correct personality ID for you specific washer model in order for the correct dial options to appear.

@enriquerivera8017 Жыл бұрын

Which test should I run if i keep getting “supply h20” code?

@NicholasSiplivy 8 күн бұрын

Means your water pressure switch is bad

@kjac081 Жыл бұрын

Thanks for this. My washer looks identical to yours, bought in 2020. My fabric softener dispenser isn’t draining during wash; after cleaning the tray and eliminating that, I ran the test modes for both the fabric softener and bleach dispenser and during both tests, the bleach dispenser nozzles are activated. Meaning my problem is that the washer is not activating the correct water outlet for the fabric softener dispenser. Verified by observation with the dispenser tray removed. Any suggestions? I’m going to check firm ware, but not hopeful.

@bensappliancesandjunk Жыл бұрын

Sadly it's likely a board if it isn't sending voltage

@ThePrintHouse Жыл бұрын

Omg I'm here for the exact same problem. Bought in 2020 also. I wonder if there was a firmware update.

@bensappliancesandjunk Жыл бұрын

@@ThePrintHouse yes there is from my understanding.; Only available to technicians with the GE SmartHQ / SmartHub system I believe. I am trying to see if I can buy one to rent out to people having this issue so they don't have a $300 service call fee for it.

@ThePrintHouse Жыл бұрын

@@bensappliancesandjunk It's crazy because this did not exist in the past. It is a new thing happening. GE should fix this immediately. Or at least if it does require a technician it should be free of charge. My girlfriend does all the laundry and told me it has been having issues recently and that it used to work well, so I dont know how many weeks / months it has been acting up.

@bensappliancesandjunk Жыл бұрын

@@ThePrintHouse if its past warranty they just dont care

@georgettewatkins4454 2 ай бұрын

Washers today are design to break down I have had this washer service at least five times it’s only three years old what happen to washer lasting at 6 years with no service call🤔

@119pwarren Жыл бұрын

My GE is 12 years old I never had a problem with it until now . I love my washer and dryer . Fixing to try the code error now .

@skeeterhawk439 8 ай бұрын

They didn't make this model 12 years ago.

@user-py4pm3lk6q 6 ай бұрын

This video was very helpful in diagnosing my problem. I had error code 3, so ordered a new inverter board, installed it, and the washer started working again ! Well it lasted 2 weeks, and then it stopped working and back to error code 3. I guess I can assume I have a lemon, and it probably fried the new inverter board ? Anyone else experienced this and resolved it somehow ?

@golfergears Жыл бұрын

Ben, will this work on GE Model GFW450SSK0WW?

@christopherhouston755 Жыл бұрын

Thanks, Ben, for the excellent video. However, my washer won't go into the test mode. When I hold down the play button at about the 10 second mark you hear a click and a light flashes inside the tub and that's it. Do you have any idea what that means? Thank you for any and all help.

@michaelerbes7517 Жыл бұрын

Try turning the unit on, press and hold the "start/pause" button, the navigate to the "self clean" option and then let go. Should put you in the diagnostic mode

@katiemacdonald5081 10 ай бұрын

@@michaelerbes7517this worked for me. Thank you!

@davecsisq 6 ай бұрын

How do you clear the codes once fixed?

@bulljustin Жыл бұрын

Thanks for this. Where can someone find the text for the error codes and the tests?

@tragle311 Жыл бұрын

The sheet with all the information is actually located inside the washer taped underneath the top panel. I found it when disassembling mine from this video!

@mosheshpinel3108 Жыл бұрын

How do I cancel all error codes? i.e. Reset. Unplugging doesn't seem to work.

@CAlibanMan 9 ай бұрын

Read this if your unit only spins for 5 seconds and ends the cycle after a few minutes. Run test 14 and 26 for confirmation that the unit doesn’t spin more than 5 seconds and ends the cycle early. Reset all of the faults on test 16. Power off the unit, run the rinse and spin cycle, but turn off rinse before starting to prevent water from dispensing. The unit should fail again. Run the troubleshoot mode again for a fault. If Test Code 3 only shows, it most likely will be the inverter board. The board is on the bottom left of the front of the unit, so it’s easily accessible after you remove the front panel of the unit. You’ll need to unscrew a screw that holds the housing in place and slide the housing container out towards you. Replace the board and you should be good to go! Good luck. Fixed my unit in 1.5 hours. You can purchase the board from the GE Appliances part store online.

@pelicanwave46 4 ай бұрын

Thanks a ton! I fix them but wasn't sure if it was the motor or the inverter board.

@Shkrelic 21 күн бұрын

This was super helpful for me. Just replaced the inverter board and back in business. Thank you for this!

@jmarkus15 12 күн бұрын

I have the exact issue, discovered this week. I bought a new board to replace. Question is -- can I access the inverter board from the bottom without taking off the whole front panel, etc?? there seems to be a large opening on the bottom panel

@joshmoody0902 6 ай бұрын

I can't seem to get the spin or tumble test to even start. I hear a feint humming when I hit the play/pause button, but that's it. I don't even hear the door lock. I can manually spin the drum fine and it seems to try to engage and does a quarter spin or so if attempting a rinse/spin cycle.

@bensappliancesandjunk 6 ай бұрын

I need to make a video on this, but 99% chance its the inverter board.

@orryslade4810 2 жыл бұрын

How do you tell if your control panel is bad? I went though all the steps. And everything works but when doing on its self it will skip steps and turn off fast

@OutdoorMore1 Жыл бұрын

Same here after 3 minutes it completely shuts off

@rileyp8605 5 ай бұрын

Assuming it needs to be hooked up to water??? I’m tinkering with one in my shop. Thanks

@jimmycole4972 2 жыл бұрын

I have the exact washer pictured in the video. Won’t drain or spin. Trying to put it into diagnostic mode by holding the pause/play (same one you’re holding) I get the click around 15 seconds but nothing changes. I’ve held it as long as 2 minutes with no display change. Any tips?

@bensappliancesandjunk 2 жыл бұрын

I believe GE has a bulletin for that one - it may be a bad control board. If its still in warranty, I'd call a local repair person that GE-authorized. May be able to get a new board free.

@jimmycole4972 Жыл бұрын

@@bensappliancesandjunk After four service appointments - they found it to be the control board. Spot on!

@dejake4589 10 ай бұрын

Don't know why, but I can't get the error code display at all. I tried unplugging, turned on and off, etc. After holding down the start/pause button for 10 sec, the only thing I get is the interior light turning on and off once. Also due to draining from the front of the washer, I did clean out the lower filter, and still got drainage from the dispenser area. After removing the dispenser drawer, I saw a tide pod plastic casing covering the drainage hole. Wifey claims she must have been half asleep when she did that .

@robertmccall9069 7 ай бұрын

Our GE Front Load clothes washer stopped working on Christmas night - middle of the wash and wouldn’t drain. Looked for kinks and blockages in drain pipe and drain pump but none. Installed a new drain pump but still stops mid wash and won’t drain. I can get it to manually spin even with water in it - but can't get it to manually drain. Thanks

@moniquetraynham2470 2 ай бұрын

Same. Did you have to replace or dinyiu fix the issue?

@shawndevito6764 Ай бұрын

Same exact thing just happened to ours. Changed drain pump and still doesn’t work

@robertmccall9069 Ай бұрын

I had to change the computer board found in the far right corner of the top - worked after just fine

@shawndevito6764 Ай бұрын

Thank you! We’ll try it out. 🤞🏻🙏🏻

@joshhardy5646 6 ай бұрын

H2O supply error is likely due to a bad water valve. This was my case. I replaced the water valve and it fixed it. Probably had corrosion and particles that made it into the valve.

@stacielawrence8651 Жыл бұрын

My washing machine is in control with lock next to it land it doesn’t let me watch close what should I do

@JasonHolmesutahholmes Жыл бұрын

I can't seem to put my washer into service mode. I've tried pyshing the start button and rotating the knob 180⁰. No flashing lights appear, just normal cycle

@nathandrakesimpson Жыл бұрын

So I saw on a comment on here about them turning off every ten seconds. And clicking.. and you saying they have control board issues.. I also saw a video of someones doing the exact same thing on reddit and they said they replaced the control board and it fixed it.. So I ordered the board and swapped them out and it does the same exact thing.. Im an HVAC Technician and instal control boards all the time.. is there something specific on these that you may have to do?

@indigrebel 3 ай бұрын

Any updates on what happened? My washer started doing the same thing this evening. So trying to find some help on the issue

@bmwe30lvr Жыл бұрын

This is great any chance to do bosch washers? Mine has been super reliable 15 years old now…: only had to replace the shocks. It’s a small front load bosch axxis mostly for apartments.

@RuthBentley-vi2ot 8 ай бұрын

My washer won't start and I checked the breaker box and inserted the outlet plug elsewhere. Thanks for any suggestions. Does the washer have a reset code?

@AdamL43728 3 ай бұрын

Up-voting, looking on how to reset as well. (It's note hold start/pause until E00 appears, that's for another model washer)

@jwollen84 3 ай бұрын

My washer is unresponsive. Light on in the tub but no led no sounds on when buttons are pushed. Any thoughts? Turned off brake for 30 minutes when turned back on the light is on in the tub and it sounds like a pump is running. Nothing on the control panel. Tia for any help.

@stacielawrence8651 10 ай бұрын

If the washing machine GE 2022 the light inside is blinking non-stopping what causing that? Another question when the washing machine I turn it on started turn off on off on and off not stopping and what that means?

@indigrebel 3 ай бұрын

Hello. Do you have an update on what the issue was? My washer just started doing this. It' comes on but for about 5 to 8 secs and shuts off.

@MegaAwsomo3000 Жыл бұрын

Is there a link to the test mode directions or a tech sheet for this unit? If so could you provide it please I would really appreciate it!

@bensappliancesandjunk Жыл бұрын

Not yet. Next one I get in shop I'll see if I can't make a guide for

@MegaAwsomo3000 Жыл бұрын

@@bensappliancesandjunk thank you you’re awesome!

@mrkeithleeman1998 5 ай бұрын

My washer was throwing codes 26,37,38,39,89 and 92. Ran through test 14 and 24 and both passes. Cleared the codes and we'll see if they come back. Only problem I've had with it is it randomly shut off during a cycle one time. My washer is the exact same one in the video.

@amandamartin708 14 күн бұрын

First time getting it fixed Jan 2023 the motor wire was cut during manufacturing and was barely hanging on. They replaced it. Now it’s showing error codes 68,27,38 problem is it’s not spinning. During the technician visit it was spinning fine. Did a washer update one load was fine second load not spinning not even a little. Now I’m not sure if it’s the inverter that needs replaced or the mother board. Maybe a new motor?

@amandamartin708 14 күн бұрын

Also during the spinning test 14 it doesn’t spin at all.

@norishiomi Жыл бұрын

Hi Ben, Thank you so much for putting great video together. Very informative. I have same unit I love and after clear multiple codes 3,19,9,26,27,38,39. I did reset and cleared codes. but Code 3 comes back after spin test (drum rotates 3-5 sec then stop). I checked wiring and conditions are very good. I suspect faulty sensor but GE does not sell hall sensor for this unit.... Any suggestion what to do before call expensive GE tech? Thanks!

@rabidpigeon Жыл бұрын

My washer is having the exact same problem :/ I haven’t been able to figure it out yet either.

@Agileet Жыл бұрын

@@rabidpigeon Any luck? In the same boat :(

@Agileet Жыл бұрын

Any luck? In the same boat with almost exact same error codes :(

@rabidpigeon Жыл бұрын

@@Agileet I just fixed mine today! It turned out to be a bad inverter board. Just replaced it, and everything works again. Part number WH22X35837

@Agileet Жыл бұрын

@@rabidpigeon Thanks for the update! I ended up replacing the inverter board. Sadly, after 2 cycles of washing perfection, I am back to square one with similar errors codes (3, 46, 25). Darnit I was so close!

@MichaelAndreSmithAndyCollins Жыл бұрын

When I get to 3:20 in the video, I hold down the start button from a blank screen and turn the knob, but the machine immediately cycles through the different wash modes; it doesn't do for me what it did for you. I've tried this after unplugging the machine for 30 seconds, 2 minutes, and 5 minutes I got my codes, but I can't troubleshoot or clear them. Ideas? Thank you.

@graphixguy3128 Жыл бұрын

I'm having the same issue, can't figure out HOW to enter the diagnostic test mode the way he did it...

@wadegerber4668 Жыл бұрын

@@graphixguy3128 same problem here

@bretmarrs4590 Жыл бұрын

Hold down the start button, rotate dial 180 degrees or a little past, let go of the start button, the lights should start flashing. You are in diagnostic mode.

@gedertr 2 жыл бұрын

How do I do this on the dryer? I have a gas dryer that started blinking and my wife hit some buttons and now the dry times are different. I think it needs to be reset somehow

@joannaacosta2409 2 жыл бұрын

Robert, did you end up finding the solution for this problem. Mine is doing the same thing.

@gedertr 2 жыл бұрын

@@joannaacosta2409 if I remember correctly I followed the same steps but turned the dial the opposite direction and it went into a reset mode…seems to work now.

@dominikslomba 4 ай бұрын

Hi Fabric softner has water in it, each time we wash. We never used any kind of fabric softener so I know its not clogged. On occasion there is a small amount of water in the front during fill cycle….I have taken it apart and checked for leaks and can’t figure it out

@6thDAY 4 ай бұрын

I am having the same issue!!!

@Hhhhhgggihgdd 4 ай бұрын

@6thDAY had the same problem and took it out and took apart and cleaned

@Hhhhhgggihgdd 4 ай бұрын

Had the same problem and took out and took apart and cleaned it.

@6thDAY 4 ай бұрын

@@Hhhhhgggihgddyup I did the same. There was gunk blocking the suction mechanism and after cleaning it out, the water drained now. Thank God it was a simple fix!

@rickslife Жыл бұрын

Does anyone know when the Overnight Ready Fan activates on the GE850 washer or how to activate it?

@terryd234 Жыл бұрын

This was in the video - Test Mode 25 is ONR fan goggle test

@fostercastillo1365 5 ай бұрын

My washer does not complete the washing. Water comes out, only for a Few seconds and clicks and the door can opened.

@swe3t23 Жыл бұрын

Rise and spin mode. I have one jacket. I have it max and extra rise. It’s not spinning to max and the timer keeps jumping from 10mins then it will say 12 mins. What’s going on. The jacket is this wet, not damp. I could ring it with my hand and a lot of water comes out. Is there something wrong with the spin? Brand new machine 2 days old

@skeeterhawk439 8 ай бұрын

Sorry dude this washer has problems with one item soaked things.Ring the water out and try it again.

@vhsorbeta95 Жыл бұрын

Help. Same machine here. My softener container is not getting water. Using test code 8 to test softener valve , water comes out strong on the bleach port side only. Test code 23 bleach valve gives same results. All ports are clear. All valves show about 1000 ohms +/- All getting 120v as activated. Softener valve seems to be same as bleach valve? But only one valve gets power and fills on code 23. Both valves activate on 8. In no test position can I get water out of the softener ports. Thanks!

@dominikslomba 4 ай бұрын

Did you ever figure out

@vhsorbeta95 4 ай бұрын

@@dominikslomba Yes, it was one of the 5 water valves. It electrically read good but still wasn't opening. I replaced the valves. Problem solved. The detergent/softener blue tray assembly would likely never be a problem, there's nothing really in it to fail, it just steers the water flow.

@jwollen84 3 ай бұрын

@bensappliancesandjunk 3 ай бұрын

Likely control boards shot and needs replaced. May want to replace pump as well.

@Honesty_Is_Key 6 ай бұрын

I reached out to you on your tik tok after trying this and I am having so much confusion because although we have the same washer mine was a 2020 model but during the test stage it was different from what you did.

@bensappliancesandjunk 6 ай бұрын

Uhh, I don't have a tiktok. Can you point me to what you saw on the platform?

@Honesty_Is_Key 6 ай бұрын

I didn't see an email on your page

@bensappliancesandjunk 6 ай бұрын

@@Honesty_Is_Key I don't think thats my TikTok page... I found it and it isn't me posting, although they are my videos...

@Honesty_Is_Key 6 ай бұрын

@bensappliancesandjunk Oh wow that is crazy. He may try and scam me because I did message him, but it will not work.

@Honesty_Is_Key 6 ай бұрын

@bensappliancesandjunk I have a question my washer which is 3 years old it's a GE Front loader it looks identical to the one in the video but it will fill about a few cups of water then go to wash and then end all in about five minutes.

@susandoyle2822 5 ай бұрын

I'm not getting enough water. Most of them are still dry. Any suggestions?

@marvintorres2243 Жыл бұрын

How you fix code 3 and 65?! Help

@dbarr15 12 күн бұрын

Where can I get a list of error codes and trobleshooting code/test?

@skeeterhawk439 8 ай бұрын

How do you reset the error codes on the machine your showing?

@ThePrintHouse Жыл бұрын

When I activate the softener value, the water comes out over the hole for the bleach. Any ideas??

@srtswpak47 8 ай бұрын

Did you ever figure this out? When I run test mode 8 to dispense fabric softener, it triggers the pre-wash drawer.

@evelynbates7933 5 ай бұрын

What if my washer is not lighting up with any codes. Repairman yesterday replaced control panel as he could not get codes to come up. Washer still not working. Any suggestions? Turns on but doesn’t wash like normal and shuts itself down.

@bensappliancesandjunk 5 ай бұрын

Did he program the personality on the board?

@indigrebel 3 ай бұрын

My GE just started having an issue today. It will turn on ok but after about 5 to 6 secs a click will be heard then turns completely off. If the button is hit, it comes on but again after 5 to 6 secs click and off. If left alone the clicking can be heard every 10 to 15 secs. So cant run test or anything. Any ideas?

@bensappliancesandjunk 3 ай бұрын

Main board is bad