Installation of the GL1500 Auxiliary Shifter Pivot. Product can be purchased at www.gl1500auxiliaryshifterpivo...
Пікірлер: 88
@bigbearbland3 жыл бұрын
Just put Cliffs upgrade on before an 8K trip and it was not only a breeze to put on but has worked flawlessly for my trip. DONT BUY THE CHEAP KNOCK-OFFS THEY ARE JUNK! Thanks again Cliff, your work is appreciated and shame on Honda for not paying you and having these on from the factory.
@gordononeil32485 жыл бұрын
Just fitted one of these to my 92 goldwing here in Australia, i must say what a major difference, and if u own a gl1500 i highly recommend one of these u wont regret it.
@jefferyaboyd4 жыл бұрын
Did you buy yours from this company? I called # is out of service the same person has them on Ebay. Im a little apprehensive about buying off of ebay. Seems a little shady.
@tnasburypl2 жыл бұрын
This man is a brilliant. Keeping the motion vertical is key to how the Goldwing shifts.
@N9752X4 жыл бұрын
Hi Cliff, just installed the pivot kit on my 1992 GL1500A. Great directions and part is rock solid! Thanks!
@pogwin504311 ай бұрын
A superb modification! Thank you! Received last week, installed today, and it is a huge improvement to shifting. Thanks too for the video because the written instructions were not as clear.
@viel.anthony2 жыл бұрын
Can't wait to install mine! Should arrive within a week or so, really stoked.
@MrGTOFixit3 жыл бұрын
LOVE IT. Just installed mine yesterday 7-6-2020 the fitment is great. Owners do yourself a favor and do an oil seal at the same time.
@paulgrossman31256 жыл бұрын
Installed mine yesterday, it took about 1 hour and 45 minutes. My Goldwing has a sidecar attatched so it was installed while lying on my back most of the time. While watching the video and installing the shift pivot, I noticed my bike was missing the rubber boot on the heat/shift seal so I ordered one. The hardest part was trimming the heat shield guard. After following the instructions it went on easily. Just a thought for other people. while I had everthing off I lubed all the rubber grommets for the panel with an o-ring lube (for Pools) to treat them and make panel removal easier. Also replaced some of the rusted nuts. Tried it out and the ratchety feeling of shifting is gone. My GL had 30655 miles on it when I picked it up in May. I kept thinking the missed shifts and ratccchety shifting was from not being used to a new bike. Been riding since 1964. Great product, works as described. Thanks
@rayvs5447 Жыл бұрын
Would like to hear more about your sidecar. My son gifted me a 1994 GL1500se. On a fixed income so sidecar out of reach for me. Doesn't stop me from thinking about it.
@jimeckenrode12712 жыл бұрын
Ordered mine and arriving tomorrow. Can't wait.
@jamesevans164 Жыл бұрын
I watched your video and order the shifter unit. When I unpacked it I took it all apart and could not figure how it went back together... Lols. So... I watched the video again and yeah all good! Thankyou for your unit and your Video Cliff I hope this makes you giggle. Jim.
@mattsez28797 жыл бұрын
wow....i just purchased a used 1989 GL1500, and in the rear bag was this product, in the bag un opened. Had no clue what it was, or what it was for. Glad i found this vid. Bike seems to shift just fine, however i assume they got it for a reason.
@ils3605 жыл бұрын
Did you install it?
@AC1607 жыл бұрын
Having run about 6000 km with your Shifter Pivot and must say that the gearshift feels better and more "soft"
@notewriter9103 жыл бұрын
Great video. Question: There appears to be two different style shift pivots, one with the allen/hex bolt installing from the front of the engine and the other installs from the rear, clearing the exhaust pipe which makes it much easier to install and tighten the "allen hex bolt." Which one is now available? Also "Cyclemax" is selling this product for a little less. Is it the same product? Please let me know? "Thanks"
@frankmisura15143 жыл бұрын
the shaft should only rotate, looks like it still moves up and down with the shifter pivot installed ?
@ScottVoelker-wy5dp Жыл бұрын
There’s a similar pivot inboard of the frame that attaches to the actual shift shaft. It’s a weird setup (thank you, Honda..)
@phillipvazquez2843 жыл бұрын
May I ask would that work on a gL1800 . I ask because I am having a hard time with stiff shifting from 5th gear only when I downshift from 5th gear????
@jeffsmith84492 жыл бұрын
I just installed mine have not been out to ride it yet though. I did run into a problem. if it is tightened on to the crash bar area to tight it won't spring back up from first gear the upper gears spring down back into position just fine. I thought maybe the washer was squeezing into the pivot area so I took my grinder and removed some material where it might touch the pivot area nope that did not work. So I just had to lock tight it in and not over tighten it.
@kensmith3665 Жыл бұрын
Same here. I filed away the Center part that comes forward through the pivot block and sits inside the Teflon bushing…. Thought the washer was jamming it…. Then I realized the thickness of the lower piece the should move between the back of the pivot block and the crash bar mount is too thick…. Major hassle getting this to work properly as per the video here…. Maybe that’s not a big deal… but I figure to keep filing the crash bar mount and the thickness until it returns back up to centre “neutral” as stated and shown in the video… it returns to centre or “neutral” from shifting upwards but not the other way… I may be over analyzing this because I find it hard to believe it is this finicky …. Ps I bought mine from Cycle max for big dollars because I wanted the quality original design and not a knock off….
@rogereastman31874 жыл бұрын
Looks wonderful So, did you design a set-up for the Valkyrie yet ???? How can I get my mitts on one ???
@canelane3 жыл бұрын
Look up Shifter Buddy on facebook for the Valkyrie
@davidrogers62622 жыл бұрын
I need one. I have a 91 GL1500 I that the neutral is hard to find and sometimes the shifting from 1 to 2 sometimes pops back into neutral.
@user-mi2jk2wh6b6 ай бұрын
I am changing out boards for pegs. Do you have video for that 89 wing se
@ericingro76882 жыл бұрын
i don't see what difference this makes the shaft is still flopping all over if anything it should be solid mounted with a bushing on the shaft for support
@ORTEZW2 жыл бұрын
I have a 1995 goldwing heel-toe shifter with floorboards seems to grind or clunk more than normal downshifting from second to first even at slow speeds 10 miles an hour or less the chef rod does wobble would like to use your product can't seem to pull up website to order would be great if you would post a link here and price thank you much
@SoloPilot62 ай бұрын
Instead of grinding, how about a washer to hold it away from the welds on the crash bar?
@DOUGETTASUE2 жыл бұрын
He added at the end of video, he is able to send a rubber boot if needed. How do you contact him for this item?
@richardparker39244 жыл бұрын
What am I missing here? Is it just me that sees the shifting shaft still moving up and down?
@paulaleksinko90394 жыл бұрын
kzfaq.info/get/bejne/htdgddxhq9SRcYU.html
@nicl93624 жыл бұрын
I thought the same thing and almost didn’t buy one. But, when I installed it tonight I realized that the shaft we see in this video doesn’t go directly to the transmission and instead has another linkage and shaft that it turns. The added pivot point keeps the shaft in the transmission from flexing down and it makes better sense when you can see that one.
@ydeardorff2 жыл бұрын
@@nicl9362 that little detail would have been helpful to mention
@mdb9238 Жыл бұрын
@@ydeardorff no joke. an exploded parts map should be included , I could not wrap my head around how this works because every shifter in every side case I have ever taken off a bike, the shaft just moves as if opening a jar, twist motion. after looking more extensively I can see inside there is an entirely different type of mechanism in there. It's a crazy thing, also I thought, Duuu. of course it's different! wtf was I thinking, this engine and tranny is more like a car than a dirt bike, if they had a straight shaft into the gear box to shift gears the whole shaft would be in a different location. Like you were saying though, woudl have been a great point to show for folks that have not been taking a a whole bike apart to see for themselves.
@sendink91403 жыл бұрын
I’m a machinist, I made one of these in my shop. Specs are slightly different.
@jamesadams13263 жыл бұрын
Did you make any extra?
@rosarioroberto58239 ай бұрын
Greetings Cliff, Brilliant detailed video 🇺🇸🍾🎉🇺🇸 I bought me a vintage GL 15000, and I really need your product. How do I place a order? Thank you so much for assisting me.
@ydeardorff2 жыл бұрын
Why wasn't the shift shaft immobilized so it can only rotate and not flop around? Seems with that bolt right there a block and hat bushing would have perfectly arrested all but rotational movement...
@800mxz2 жыл бұрын
How does one get ahold of how to buy one? No information on the website the link takes you to buy / order
@jamesadams13263 жыл бұрын
I need this, my 1500 is leaking oil so I will need the seal and the kit. Trying to find out how to buy it.
@jamesadams13263 жыл бұрын
Does anyone know how or if we can get a hold of cliff to purchase one of these?
@hailfriend5 жыл бұрын
Obviously you out the bolt back in the shifter lever and didn't leave it out when you said this concludes this part of the installation.
@jamespolucha69112 жыл бұрын
Will this fit on the Valkyrie also ?
@HotWingz083 жыл бұрын
Do you still make and sell these? Definitely need one but can't find them anywhere.
@edkoonce89962 жыл бұрын
how do you get the seal replaced ??
@jamespolucha87902 жыл бұрын
Will this work on the cl1500 Valkyrie?
@user-mi2jk2wh6b6 ай бұрын
How do I take engine cover on gear side.
@RanGer-4984 жыл бұрын
This work on a 1999 valkyrie?
@RockAnAhardSpot20 күн бұрын
The website to buy this won't go thru. I wanted to buy this item but the link doesn't load.
@TheCvfr7 жыл бұрын
do you know if this can be used on the GL1800
@cliffbissonnette55715 жыл бұрын
The 1800 has a great shifter. No Mike, it doesn't fit.
@rogereastman31874 жыл бұрын
How's the Valkyrie project coming..?????? Why wouldn't this product work on the Valkyrie?????? Same motor and transmission with very little to remove to gain access.. Waiting to purchase for my 97 Valkyrie
@bhauk9626able4 жыл бұрын
Anybody know of a video on replacing the oil seal? That looks like the hard part.
@funzosupport69226 жыл бұрын
I want this but as im in the uk its rather expensive :(
@mdb9238 Жыл бұрын
I have asked this question so many times it's making me a little crazy. Does this work if you have heel toe and floor boards? "99 GL1500 Aspencade.
@lattitude01 Жыл бұрын
in case you are still searching for your answer, for heel-toe shifters yes. it will work, HOWEVER, sense most floorboard kits also use the same crash guard bolt hole for mounting the floorboards you will need to make some alterations or modifications to the floorboard hardware. they usually use spacers to to clear the body panel, so if yours does you can just cut the same thickness off the spacer as the mounting block is thick and you should be golden. but there are several floorboard kits, i'm not familiar with them all and i don't know how yours mounts up.
@mdb9238 Жыл бұрын
@@lattitude01 I am going to give this a shot I guess, I can feel what I think is correctable slop, when I first got the bike I assumed, because I have never used floor boards and heel toe ) that it was just the way that works. It seems to me that there woudldnot be as many fans of this set up if they were all sloppy like this.
@thesage16215 жыл бұрын
will this work on my 2003 valkyrie?
@canelane3 жыл бұрын
Look up Shifter Buddy on facebook for the Valkyrie
@davidmccabe17253 жыл бұрын
I've been trying to purchase The shift Pivot but have no luck on cashing out? I dont use PayPal and it keeps telling me the other way is not available right now does it ever work?
@jimschwenk74693 жыл бұрын
I bought mine from Cyclemax a couple of years ago. This one is the same, the original (but improved version)it's not the cheap knock-offs you see coming out of Europe recently.
@davidmccabe17253 жыл бұрын
@@jimschwenk7469 thanks I did get one cyclemax no longer sells them. Its hard to find one with a bushing in it to many knock offs
@Handymanherb4 жыл бұрын
Ok didn't cover how to install the oil gasket
@francescoruscica5752 жыл бұрын
Perchè non si inserisce la traduzione in altre lingue per questi filmati
@jamesberry75872 жыл бұрын
Show me the price of it
@Handymanherb4 жыл бұрын
Ok you lost me with the heat shield, would have liked to see where it came from
@MrXcc4u2 жыл бұрын
that was the last piece that he took off before he installed the brace. you are looking at the inside of it in the video when he talks about trimming it with tin snips. as he pulls it off of the bike you can see the rubber slide off of the shifter at the 3 minute mark.
@rickysanches7077 жыл бұрын
how do I buy one?
@ZacVaper7 жыл бұрын
Product can be purchased at www.gl1500auxiliaryshifterpivot.com/
@dtops93716 жыл бұрын
Zac vaper how to talk to your child about sex
@jamesberry75872 жыл бұрын
Show me the price of it
@ydeardorff2 жыл бұрын
Ok I've been a mechanic for decades... What I'm seeing here is their pivot doesn't isolate the shaft from off axis movement at all. The shaft should he held still in place, and rotate on its linear axis, not move up and down vertically
@melaniemarks63592 жыл бұрын
yes, that was very confusing to me also. it certainly appeared to be moving up and down far beyond its possible tolerances. I just called it an optical illusion, I guess.....
@andyschlau63332 жыл бұрын
I agree. Looks cool but it’s a bandaide
@boostupcoverband Жыл бұрын
mechanic ? the "axis" really goes up and down, not turning like you think. At the back (you can't see) is a lever attached to a more forward (2 inches) axis which turns.
@potosinobiker82443 ай бұрын
Me interesa uno por favor a que número llamo
@RockAnAhardSpot17 күн бұрын
I bought the China crap one and got all my money back from that liar, he literally has stolen your pictures with the bushing and everything, the whole unit is sloppy and rough. it has so much slop it appears that it will break. i would never install that. However, your link no longer goes thru to buy this direct from you. I have a 99 Goldwing GL1500 with markland floor boards and heel toe shifter. my oil seal is wet with oil but not dripping, i;d like to get this done asap. my bike has only 75 thousand miles on it and i would like it to last as long as possible, shifts fine now and I want to keep it that way or better as you have stated.
@myturbanizdurtee91596 жыл бұрын
Little Rubber Piece $30 Bucks Absurd ??, ....$125 For Two Pieces Of Aluminum Is Absurd Also...Feel Like You Have Us All "Goldwing Owners" By the "Short-hairs".....
@cliffbissonnette55715 жыл бұрын
How about 28K for a new bike? When the support bearings for the shaft completely fail, and your gearbox gives up to the ghost, then what? Each piece is hand fitted and handled many times. The packaging, shipping, manufacturing, materials, shipping and distribution costs are higher than you may think. I have taken none of these back for quality reasons. They work.
@TheFalcro12342 жыл бұрын
Then buy some billet aluminum, CNC machine, CAD program, hopefully you have some engineering and design skills already, if not you'll need to pay for some classes or training. Then sit down and design the parts you need, use your cnc to make them and then install them on the bike. I dare say you cannot do that for less than $125, not to mention that if you have used this design for your "template" or starting point you are basically stealing someone else's hard work, so there's that. If your design is an original one then you probably did not get it perfect on the first try and will then have to tweak it to make it better.... "Feel Like You Have Us All "Goldwing Owners" By the "Short-hairs"
@rogerwest5397 Жыл бұрын
How can I get 1 and how much $
@user-cg5ls2cl7f7 жыл бұрын
125 $ очень дорого !
@a-toxa4 жыл бұрын
Народ сам колхозит.
@user-tz2xk4cz5z7 жыл бұрын
"..more extravagant..""..mainly Snap-On.."Typical Goldwing owner-speak.How about using the factory tool kit for the demonstration.
@IFLYBELL6 жыл бұрын
Well the last time I looked at my factory tool kit, it didn't come with ratchets, sockets and extensions! Let alone tin snips! You must own a Harley!
@cliffbissonnette55715 жыл бұрын
I'm not a movie star or salesman. I did the best I could. I will say that you know little about factory tool sets if you think Honda supplies everything you need.