Great demo. My only comment would be that it seems more prudent to drill the hole BEFORE installing the crack expanders, as the expanders can cause the crack to run if it's an unstable one.
@malgorzatadomanska1431 Жыл бұрын
11111
@kabirmiah35592 ай бұрын
Great job I wish you guys where here in the UK, because here the windscreen repair people won't repair any cracks longer than 1.5 inches and they always say anything longer than 1.5 inches can't be repaired. All they want to do is sell you a new windscreen even though a long crack can be repaired as seen in this video and other videos of professional windscreen repair people in the USA.
@joeduong76175 жыл бұрын
Thank you for the video and you did a great job, very detailed of what's needed to be done!
@hondagoal8 жыл бұрын
Very interesting. How much a repair like this cost? It's not cheaper to replace the glass that has a better warranty ?Thanks for the upload.
@benschapero27777 жыл бұрын
How much did you charge to repair this crack? Thank you.
@markgriffiths44452 жыл бұрын
Very good presentation thank you!
@muhanadalkinani82535 жыл бұрын
Best resin and best kits glass mechanix very good
@youssefbelmajdoub92927 жыл бұрын
hanks brother for the information iam from mrocco. can you help me iwant what are the names of these machines and where to faind him thanks
@Nywindshieldcrackrepair6 жыл бұрын
Good demonstration but it must be understood that a crack repair will always be visible at certain angles and lighting conditions and can avoid costly replacement by restoring the structural integrity of the windshield.
@user-oo8sk9wm8d2 жыл бұрын
How do I remove dirt from the crack and I want to clean the crack from the dirt inside
@hachi666roku Жыл бұрын
@@user-oo8sk9wm8d In all honesty, there is no good way to get “trapped dirt” out of a crack. It’s important that if you get a client with a long crack to have them put packing tape over the crack to keep contaminants out until you can repair. I had a customer that waited MONTHS to get the damage repaired 🫣. The pvb was actually discolored from being exposed
@bhhookkick32 жыл бұрын
I've learned a lot thank you
@lmercado99997 жыл бұрын
sometimes you can just run the resin on the crack without using the injector with the clam...
@jigme95693 жыл бұрын
From where I will get those machines and kits plz suggest me
@dhawalghia2 ай бұрын
how will you repair crack if its from inner side ?
@user-oo8sk9wm8d2 жыл бұрын
How do I remove dirt from the crack and I want to clean the crack from the dirt inside
@martinalbert56534 жыл бұрын
Is your crack through both pieces of glass? I ask because if not how would the spacer work if used inside the vehicle?
@riverpinewood65603 жыл бұрын
The spacer provides pressure from inside and the resin will infiltrate much easer as the crack being “opened up”.
@martinalbert56533 жыл бұрын
@@riverpinewood6560 Does anyone in the state of NJ do these kinds of repairs and if so who and where?
@gavinparsons51508 жыл бұрын
I noticed that you didn't give us an inside view of the final result? That's because the crack is still very visible isn't it. mmmmmmm the wonders of camera angles. Some people call it proper gander.
@ianc2797 жыл бұрын
The repair will leave a slight hairline after it is completed and prevent the crack from spreading which is completely normal. Some people like this because it saves the original factory seal and saves money.
@whymustichasethecat2397 жыл бұрын
just put insurance on your windscreen and make a claim when it does crack, especially if you drive on highways and make sure they replace your windscreen not repair it, these are temp fixes, your windscreen is now weaker
@jamaluddinjaafar84596 жыл бұрын
why must i chase the cat
@gavinparsons51506 жыл бұрын
Jamaluddin Jaafar because they taste like chicken
@sebastianrodriguez82495 жыл бұрын
I rather paid my $50 deductible and get a whole mew windshiel. Since the repair to the crack will cost more and isn't worth the hassle.
@joestruckingandluthiery3 жыл бұрын
What if the crack starts at a chip and spread upward. Do you start at the chip and work up or drill at the opposite end and work down?
@user-oo8sk9wm8d2 жыл бұрын
How do I remove dirt from the crack and I want to clean the crack from the dirt inside
@Marcoosianism2 жыл бұрын
Start at the chip and work up. Working against gravity is actually better.
@lesterburtard75883 жыл бұрын
howdy, great vid , , ,need to bump uor volume
@stevestone69367 жыл бұрын
He drilled away from the break, so what good is injecting resin in the new hole? How does that help the crack?
@Marcoosianism2 жыл бұрын
I believe he angled the drill bit so that it intersected the crack at the end of the hole. The way I've seen it done however is to drill only about 1/32" away from the end of the crack then tap the drilled hole so it forms a bullseye, then press the end of the crack a little bit so it continues to crack towards the hole and terminates there, joining it.
@dl75777 жыл бұрын
What about MOT?
@mrwrolguy17173 жыл бұрын
dam that looks terrible... thanks I know not what too do now. crack expanders and now running the injector down the crack.
@Bestoflovesongs04252 жыл бұрын
Any location in philadelphia
@erikyanez94195 жыл бұрын
La reina que ocupas para llenar la grieta es muy delgada y eso se vuelve a abrir, no sirve
@fikprice98215 жыл бұрын
Can i get a private lesson about this
@NextLevelAutoDiagnostics7 жыл бұрын
What is the size of the drill bit used?
@JJ-yh9kf6 жыл бұрын
What kind of drill bit?Is it a special type for glass?
@Marcoosianism2 жыл бұрын
Should be roughly 1mm or no more than 1/16 of an inch.
@Marcoosianism2 жыл бұрын
@@JJ-yh9kf Usually carbide tipped 1mm or no more than 1/16th of an inch made for this purpose - glass/tile/ceramic. Don't use a regular twist drill bit.
@yanzhengzhang39193 жыл бұрын
Professional
@mariusdevalmont74322 жыл бұрын
I have to agree with the others...that end result looks like crap...but this video was done in 2015...7 years ago....What's up with the new resin technology.....That "Liguid Glass" stuff looks like it give phenomenal results WITHOUT the "bridge and suction" hassles
@kingtut59235 жыл бұрын
I can still see the crack
@bestclarkesspot3 жыл бұрын
The crack will not completely disappear but it will prevent further damage. This will prevent the factory seal from breaking and save you money.
@rodneyporter33205 жыл бұрын
U can still see the crack. Failed
@DFX2KX5 жыл бұрын
That's more or less inevitable. This makes the windshield reasonably strong again, and can spare you a replacement. Given how expensive a new windshield is, patching the first crack at least saves you some money.
@bghancock84 Жыл бұрын
why there was no show from inside?? all these are totally bull.... people just change your windshield. All these products least for days.
@jlopez2351 Жыл бұрын
Replace it
@user-oo8sk9wm8d2 жыл бұрын
How do I remove dirt from the crack and I want to clean the crack from the dirt inside
@Marcoosianism2 жыл бұрын
I would use a strong vacuum first, then maybe compressed air to blow out any remaining dirt.