GM 2.4 Ecotec Camshaft Position Sensor

GM 2.4 Ecotec Camshaft Position Sensor - How To Test & Replace

Рет қаралды 485,997

6 жыл бұрын

In this video we go through the process of diagnosing the problem with my car via an OBDII scanner, testing the probable Camshaft Position Sensor failure and replacing the part. My vehicle is a 2012 GMC Terrain but the process should be essentially the same on any 2.4 Ecotec engine.
The links:
Exhaust Camshaft Position Sensor - #12655421, genuine GM replacement - amzn.to/2EOKWz7 (affiliate)
Intake Camshaft Position Sensor - #12655420, genuine GM replacement - amzn.to/2BhDU6v (affiliate)
OBDII Scanner - amzn.to/2EuD4W9 (affiliate)
Multimeter - amzn.to/2EQYzy4 (affiliate)
Tools Needed:
Ratchet w/ Extension
8mm socket
10mm socket
Pliers / channel locks
Slotted / flat screwdriver
ODBII scanner (if you want to check your engine codes)
Multimeter (if you want to test the camshaft position sensor)

Пікірлер: 169

@TheStruggleville 3 жыл бұрын

Enter the giveaway on my site for your chance to win a $50 Home Depot gift card! (Ends 9/21/20) - struggleville.net/lootbox

@davidanderson8778 5 жыл бұрын

Dealer quotes $400 to fix. O'Reilly's part cost is $50 and only takes 15 minutes. Thanks again for the video. Saved $350.

@firebomb80 2 жыл бұрын

Not sure if you check old posts, but I have a 2011 Chevy Equinox and I just had to replace these, instead of taking it to a shop "440.00" I was able to buy the parts "29.99 on amazon" and fix it myself within 45 min. thanks so much man

@lgoamity 2 жыл бұрын

I wasn't expecting it but with this Video I was able Pull the Exhaust Solenoid, clean it, test it (with questionable results) reinstall and after some road testing the code(s) cleared. (Before the testing was able to clear the pending codes, with just a "permanent" P0013 sticking around) So I saved around $30-$100 and time getting the parts. The part I have didn't even look dirty. Screens/Ports looked Good. Oil Level and Condition good too. Don't think I've ever seen Sludge Buildup in this engine but a quick cleaning seems to have done the trick.

@ronrobertson5513 2 жыл бұрын

You saved me $300 with this video. Thank you.

@ryanbennett8524 4 жыл бұрын

Thank you SO much. I could hardy sleep last night worrying about what the problem was. Went to auto zone and got it read and mine was the intake. Watched your video and got it done. Lots of DIY videos are confusing or gloss over important steps but your video mixed with what you were telling me got me all the way through no problem. THANK YOU!!!

@mrob5278 3 жыл бұрын

I know you posted this a while ago.....but I just wanted to say thank you so much for taking the time to make this video. Seriously, you saved me from having to take the car to a mechanic and getting completely raked over the coals. Thank you again! Great video......the money I saved I'll have a beer for you tonight.

@MrRoadside616 4 жыл бұрын

This has been the most detailed and helpful video I have ever watched for working on a car. Thanks to this i now have full confidence in fixing my terrain! Subbed

@Joe.B007 5 жыл бұрын

Thank you for making this video....as someone in the medical field I rarely get a chance to save money on care repairs. You saved me $ 300 ! ! God bless and keep making those videos my friend.

@TheStruggleville 5 жыл бұрын

Thanks, glad it could help!

@anaolivares2549 5 жыл бұрын

I just wanna say thank you so much for the video it helped me and engraved a valuable lesson in my life it's funny how one never stops learning or being able to learn from a complete stranger you got a good heart keep up your wisdom open

@sethflood1545 3 жыл бұрын

Thanks man!! Saved my buddies mom 200 bucks!

@KurtHite 4 жыл бұрын

This is a great video. I just wish you would update the title. These are intake and exhaust VVT solenoids. The actual cam sensors are on driver's side of the vehicle on front and back of the cylinder head.

@sarcasticcat4982 4 жыл бұрын

Are they what is represented when a p0017 code pops up?

@kudat5480 3 жыл бұрын

Yep! That's the actual part title. Variable Valve Timing Solenoid....VVT Solenoid.

@matthewstiles353 2 жыл бұрын

@@sarcasticcat4982 P0010

@oldmarine3438 8 ай бұрын

You were replacing the camshaft position actuator/solenoid, not the camshaft position sensor, which is located on the sides of the cylinder head at the driver's (left) end of the engine. The links to Amazon actually call these components by their correct name. No complaints on your troubleshooting and correcting the problem, just wrong terminology.

@hembilkhu3439 5 ай бұрын

Yes you are right what he changed is called Actuator/solenoid the Camshaft position sensor is different its on the right side of the engine near the battery i found that there are 4 sensor in my 2012 chevy Equinox 1 intake Actuator and 2 Exhaust Actuator and 3 intake Camshaft position sensor and 4 Exhaust Camshaft position sensor thanks for correcting him...

@jacemonney1802 2 ай бұрын

Thank you for this

@anthonygarrett6896 5 жыл бұрын

I've watched several videos on this subject and this one is by far the best one. Thank you very much.

@norm51167 5 жыл бұрын

Thank you so much. Did mines this past Sunday so far so good. I bought 2 of these came as a pair from Amazon for $28.00 free shipping

@sarahwoods5764 2 жыл бұрын

Looks very detailed. My car will not start and I have this exact code reading problem. I'm gonna try this out and I hope it works

@musaghsk4092 2 жыл бұрын

Any luck

@sunnyred37 4 жыл бұрын

Thank you for video. I replaced my intake one in Sept. 2018, with your help from this video. My check engine light came back on now and it is the same thing. Last time just replaced the intake. This time I'm going to do both. As soon as that code came and how my car was acting I knew I had to come back to your video. Thank you so much!!

@JESSEPAVON 4 жыл бұрын

What a good video man. Amen to your last rant. I do all my mechanic work, my wife and i have 4 vehicles and you cloud just imagine what I’d spend just in cutting rotors and break pads, oil change. Not to mention other more expensive stuff. PEOPLE PLEASE MAKE YOUR BEST EFFORT TO DO YOUR OWN MECHANIC WORK. This job seriously is a walk in the park. Again thanks for the video.

@jeremyrefior1201 5 жыл бұрын

Thank you for this video! Had my sensor replaced by the shop (p0014) a year ago and it was covered under my Warrenty. It was roughly 600.00 bucks that I didn’t have to pay for due to the Warrenty but just a few days ago my engine light turned on again and according to OnStar it’s the same exact issue (p0014) if the part isn’t covered under their parts Warrenty than I’m going to do it myself. Thanks again!

@rebeccachilton416 3 жыл бұрын

I’m waiting on my parts from Amazon now. As soon as they get here I’ll be replacing both my intake and exhaust solenoids. Thanks for the informative video!!

@davidelberson4025 5 жыл бұрын

Thanks for the assistance! Replace both when one went bad thanks to your help...

@muerte312 6 жыл бұрын

Thanks for the video it was just what I needed. Informative and easy to follow. Fixed the problem. Thanks again

@larryrussell9078 6 жыл бұрын

Thanks a lot for the detailed video. I'll be fixing this week. Awesome video.

@robertilk4200 5 жыл бұрын

this video on replacement of camshaft solenoids was excellent !!!

@josemercado9774 4 жыл бұрын

Thank u so much. Took us 25 mins and $100 because we replaced both!

@dollarshooters7069 5 жыл бұрын

Good video. Repaired exactly as shown and with the tools you listed. Thanks man.

@TheJoygazmic 3 жыл бұрын

Thank you, showed me everything I needed to replace both sensors

@adammrichardson0825 3 жыл бұрын

2012 Chevy Equinox. just did mine in about 30 minutes and $95 for the pair of sensors at NAPA. Thank you.

@starpacheco3426 2 жыл бұрын

Thank you so much, this video was very much needed … currently having this problem as me and my family are on our way to Panama City.

@jerrykast7713 3 жыл бұрын

Thank you. Just what I needed & you delivered with a lot of class.

@az8theist977 4 жыл бұрын

Good video. The "crazy horseshoe" is Omega, the symbol for resistance. Plus, when you first turn on the meter you should touch the leads together to measure 0 ohms. That way you're sure the meter and leads are working correctly.

@jodymilburn7343 5 жыл бұрын

Thank you for your video. I followed your instructions and succeeded! I can't believe the dealership could even think about charging so much for something that took me half hour to do and that was while holding my 4mo old granddaughter in one arm during it! Lol

@austinstephenson9745 5 жыл бұрын

Oh man thank you so much for posting this my wife's 2011 Terrain just threw a P0014 code and has a rough idle and stalls out periodically. Going to check these sensors now! Hopefully it fixes it. You may have just saved my life.

@briancooley2192 5 жыл бұрын

Did this fix your problem?

@jjc032681 4 жыл бұрын

@Austin Stephenson ...and?????

@britjamaine9229 5 жыл бұрын

I need to add it’s because of you I am getting new pistons and rings after six months of a consumption test and waiting for an available tech. There wasn’t a recall issued for Canadian models even though they have the same problem

@matthewmorin3938 5 жыл бұрын

Thanks for video!!! Saved me some money on labor and instructions were easy to follow. Problem solved

@AM-kg5kb 5 жыл бұрын

Thank you for this. SUPER EASY and saved me some stress & $$.

@The_Collective 3 жыл бұрын

So I'm getting ready to change my oil, and I had a friend a few months ago use a scanner to tell me what my check engine was, because it wasn't a constant thing. It had said it was the camshaft sensor. Anyway, I had gotten to the "mouse nest" part and laughed, because I had paused when you said to remove the cover. When I removed it there was a spot with bits of thread and whatnot near the oil cap area.

@oneldjekounmbaye2979 5 жыл бұрын

I just wanna say thank you so much sir, your video help me a lot did change mine🙏💕🙏💕God bless you,

@wookiec41g 5 жыл бұрын

This saved me sooooo much money. Thanks!

@johnmccomb6072 4 жыл бұрын

Thanks man , you’re a blessing

@Richard-jl8vd Жыл бұрын

Thank you for the video.....if it should read 8 ohms what about the other one should it read 8 ohms also?

@jujitsu62 6 жыл бұрын

Awesome video guy ... You helped save the day . Thx

@alfredoluciano5794 6 жыл бұрын

Great video I love it I’m sure it will be very helpful for one of our KZfaqrs

@Phoenix-Rising4 5 жыл бұрын

Since I dont work at the car dearlship anymore,I have to find someone else to replace it. I refuse to pay $400-500 to fix my camshaft, when I can do it myself. Thank you for this video

@lgoamity 2 жыл бұрын

Thanks for the Video. Besides breaking the White/Beige Plastic Tab on the Exhaust Value's Electrical Connector (I was expecting it to pull straight out)... after cleaning the Valve and reinstalling/testing the road test cleared the codes so You saved me at least $30-100 in parts. As it seems redundant I'm hopefully I'll have time to find some replacement tabs for the Electrical Connector(s)... Hopefully GM doesn't charge $20 each. Might invest in the removal tool if they do...

@evanmendez-perez5960 4 жыл бұрын

Great video man. You helped me a lot

@yomero1978 5 жыл бұрын

Do you have any video of how to disconnect the battery safely? I was reading in the manual, something about drainning the on-star back-up battery, if you disconnect the main batttery the "right" way.

@dcox0713 3 жыл бұрын

Good video. 2015 equinox and it guided me right through it.

@austinsantos1113 2 жыл бұрын

Dan did u ever have one go out WITHOUT the light coming on?

@Greop 3 жыл бұрын

Had a mouse nest in the exact same spot lol. Awesome!

@Ph0t0bug Жыл бұрын

Hey, had to do mine in New Orleans with 108 feels like temp… I understand your suffering with the snow.

@dandunning4409 2 жыл бұрын

GM Dealership wanted $350.00 to replace both because they said both Intake and Exhaust were bad. My son in law replaced both for under $50.00 and it took less then an hour. Goes to show you just how bad the Dealership will rip you off.

@alexgavino1979 5 жыл бұрын

Thanks for your video I have a question, did you thing it is a good idea to verify the ohms with the sensor installed, or need to be uninstalled?

@markv.4151 5 жыл бұрын

Awesome video thank you quite kindly... !!

@shoynjones8422 2 жыл бұрын

Very informative great job with the video

@Joshua2424ND 4 жыл бұрын

Thanks for the video. Used to fix mine.

@terenceking7721 6 жыл бұрын

Thanks Brah for the video. I have a 2011 GMC Terrain eco. I’m bout to try it now lol!!!

@derrickhance3045 3 жыл бұрын

Do you still drive your terrain?

@tedweaver4526 5 жыл бұрын

Thanks so much for this. Really helped me out. Hats of to working on this in freezing weather. just did mine in 75 degree weather. I'm such a wimp. $61.00 a piece for these things in Southern California from the Chevy dealer BTW.

@docstar3809 6 жыл бұрын

Was looking for the right obd2 tester for crankshaft and camshaft sensor that will work. Thanks

@britjamaine9229 5 жыл бұрын

I was quoted $517.00 with them say this is hard to get at.while the engine is apart for recall this would be a good time to fix it, thanks for the info

@cswann8 4 жыл бұрын

Good stuff....just bought a used Terrain...literally on the way home the check engine light came on. Then I saw the date on the dash info screen was Feb 26, 2012.....so the scumbag that sold me the truck disconnected the battery to conceal the fault. It came up as a P0014 Got a pair of CMP solenoids on the way.

@TheStruggleville 4 жыл бұрын

A heads up on the 2.4 if you don't already know about this problem they have - kzfaq.info/get/bejne/sL1jpNmevrHJZZ8.html

@javiermartinez5878 4 жыл бұрын

Great video my friend.

@jodymacfitness9799 3 жыл бұрын

Thank you SOOO much for this video. I was quoted $850?!!!

@asifaslam1111 5 жыл бұрын

Great job bro

@texfulton 6 жыл бұрын

Good Job, Thank You !

@ant1030diaz 5 жыл бұрын

Thanks it worked for me

@xezaro 5 жыл бұрын

very good video . thank you

@brandonbowman1285 4 жыл бұрын

Thank you so much for the video. I have a 2012 Terrain and was able to complete this project in about 45 minutes.

@kylerdowns695 2 жыл бұрын

cap

@z33tanner 5 жыл бұрын

2008 Saturn Vue with a P0340 and P0341 Only says Camshaft position sensor A circuit manufuction. Thank you so fuckin much for the information about the A for intake and B for exhaust couldn't find that anywhere.

@z33tanner 5 жыл бұрын

Replaced both cam sensors and vvt solenoids still coming back up.

@user-ui3lx7ie4p 9 ай бұрын

Great video

@wingback806 Жыл бұрын

I Replaced both but the code is still there and car still feels like before ( staling and reduce power)

@StingyJ 4 жыл бұрын

I just tested both of mine ( 2012 Terrain 2.4l), and the resistance for both intake and exhaust was 12.5 and 12.6. I'm stumped. Aren't they supposed to be between 6 and 8????

@pamgibson3848 Жыл бұрын

Mine registered 9 on the ohms meter. I have already replaced mine and now it’s ticking. The motor wasn’t doing that earlier. It only threw one code one time.

@gracetheroux4219 3 жыл бұрын

Hi, there! Very good video! Not many people explain their walk-through of the reaper and show every step like you do; thank you!! But is this the same process for a 2013 Equinox that has a V6 3.6L?

@TheStruggleville 3 жыл бұрын

Thanks! Unfortunately that is a different engine so it will be different

@01bluebusa 5 жыл бұрын

Mouse nest?? I thought that was a 1970s muff!

@cesarjorgemurillobarientos1813 4 жыл бұрын

very good my brother

@kudat5480 3 жыл бұрын

It takes me 5 mins to remove both. 10 mins to go to O'riellys test both get the one i need. 5 mins to put it back together. 20 minutes total. V V T Solenoid! Variable Valve Timing Solenoid.

@dougnichol6919 3 жыл бұрын

THANK YOU!!!!! SO MUCH!!!

@thehoward3940 6 жыл бұрын

Thank-you !

@dnfwme 5 жыл бұрын

Can you guide me where Crankshaft sensor of 09 Saturn vue 2.4 is ?

@justanornallife 5 жыл бұрын

Thanks, good video....

@303gangsta13 Жыл бұрын

i got the code p0014 i replaced both of those solenoids but the light keeps coming back with the same code 2012 terrain 4cyl

@saanimohammed3815 Ай бұрын

Please how does the behave when this fault code is found?

@williamrobinettejr4976 2 жыл бұрын

Did this give you a powerloss as well?

@jordanblair5474 3 жыл бұрын

Do these engines have power steering fluid and if they do where can it be checked ?

@tgi_fridayy9117 5 жыл бұрын

Thanks for the video, if I'm getting p0013 and p0014 does that mean it's the intake and the exhaust sensor? 2015 chevy equinox lt 2.4

@TheStruggleville 5 жыл бұрын

I don't remember which code is specific to which part but its easy enough to pull them both out and test them.

@crand20033 5 жыл бұрын

How many miles do you have on it? If it is less than 100K it's under warrantee.

@davidanderson8778 5 жыл бұрын

Thank you

@davidcrittenden5661 5 жыл бұрын

Thank you...

@janvincentaguilar7722 5 жыл бұрын

I'd like to know the specs on a 2014 chevy equinox vvt camshaft position actuator solenoid. I'm replacing them due to a P0011 error code. I bought AA ignition intake and exhaust solenoids. Im testing them before installing them and notices the resistance is reading about 3 ohms higher (8 to 10 on older set, about 11 on newer set). Will this affect part and overall engine performance?

@briancooley2192 5 жыл бұрын

Did replacing the sensor fix your problem with the p0011 code? My 2015 equinox is throwing the same code

@ambermaher2693 4 жыл бұрын

Thanks SO much!! You saved me so much money. God Bless you.

@TheStruggleville 6 жыл бұрын

The links: Exhaust Camshaft Position Sensor - #12655421, genuine GM replacement - amzn.to/2EOKWz7 (affiliate) Intake Camshaft Position Sensor - #12655420, genuine GM replacement - amzn.to/2BhDU6v (affiliate) OBDII Scanner - amzn.to/2EuD4W9 (affiliate) Multimeter - amzn.to/2EQYzy4 (affiliate) The volume goes way down about halfway through the video. Hopefully you can still hear everything. If you watch till the end you will hear about the problems I was having while making this video.

@uncleb727 5 жыл бұрын

What year is this vehicle?

@Phoenix-Rising4 5 жыл бұрын

@@uncleb727 2012

@kingrichards101 4 жыл бұрын

Did you disconnect the battery before replacing the sensor?

@robinpesencie2981 2 жыл бұрын

Hi, I live I South Africa. Please send the link of information and the brand of coding machine/tool that you are using. Appreciates it.

@keving52002 3 жыл бұрын

Good video, any problems with high oil consumption on your vehicle?

@TheStruggleville 3 жыл бұрын

I got rid of mine before that started but it appears a lot of people have that problem - kzfaq.info/get/bejne/sL1jpNmevrHJZZ8.html

@keving52002 3 жыл бұрын

@@TheStruggleville Yes I like the new look of these vehicles and I was considering buying a used one. There's a couple of fixes that you can do yourself such as just cleaning out the PCV valve and hose with carburetor fluid, and some people suggest getting a vented oil filler cap that will resolve that problem and keep the rear seal from blowing.

@TheStruggleville 3 жыл бұрын

I wouldnt buy anything with that 2.4l engine now that I know about the problems. Just not worth the hassle.

@kreeplok123 3 жыл бұрын

I just replaced the one on the far side with the black plastic plug in, and oil is leaking all over, can i be a bad part? I made sure it was snug down but its leaking pretty good

@TheStruggleville 3 жыл бұрын

Sounds like its not seated properly. I did this video quite some time ago so the details are fuzzy but it you may want to take the bolt out and wiggle the sensor a bit to see if it will go down any further. Also I believe it has a seal on it, maybe you are missing the seal or sometimes its possible for the old part to leave its seal on the engine and doubling up on the seals can cause a leak.

@jamesfinney8841 2 жыл бұрын

Dude I had a little nest the same color, size, and location in mine, lol.

@rodolfoolmos7656 4 жыл бұрын

1 ohm or more means that there is enough resistance for a circuit to be open les than one means that there is continuity and that the circuit is works.

@silveraero722 4 жыл бұрын

P0011 easy fix. Thanks.

@mikelowery8430 Жыл бұрын

okay sweet so this doubles as replacing the VVT (Variable valve timing) solenoids that are both (Exhaust and Intake) that are going out on my 12 Equinox 2.4

@eyeonart6865 Жыл бұрын

What about the relearn they say you have to do and to relearn you need a $2100 scanner or a $269.00 Tech II scanner

@robertogutierrez3600 5 жыл бұрын

it is necessary to reset te PCM after change the solenoid?? If so how can I do it

@TheStruggleville 5 жыл бұрын

Just erase the codes coming up with a scanner

@worthey1969 3 жыл бұрын

Okay I just pulled mine out I got a bunch of bearing material in mine stopped it up I guess it's crankshaft bearings I don't know it's not knocking or anything