How To Fix That Pesky TAIL SHAFT LEAK

No video

How To Fix That Pesky TAIL SHAFT LEAK

Рет қаралды 57,912

Жыл бұрын

HELP! MY TAILSHAFT IS LEAKING!!! No worries, I got you covered! Here is what you need to know.
You can do it... I believe in you...
GODSPEED GARAGE T-SHIRTS and MORE!!!
**Get FREE SHIPPING on orders over $40 using code FREESHIP40 **
GSG MERCH: godspeedgarage...
PARTS USED:
OIL SEAL AND BUSHING KIT:
www.amazon.com...
TAIL SHAFT O RING:
www.amazon.com...
Copyright GODSPEED Garage, LLC. 2023 All Rights Reserved
*Disclaimer - This video is intended for entertainment only. GODSPEED Garage, LLC, or anyone involved in making this video is not responsible for any damage to person or property that may occur attempting this on your own. You assume all responsibility for your own safety as well as use of your property.

Пікірлер: 52

@jessemurray2236 2 ай бұрын

I watched this video a week ago not thinking you have the same tail shaft as my truck. I’ve been searching for this seal and bushing for weeks. Thanks!

@frankkennedy5361 Ай бұрын

Concise and clear, with excellent advice. Thanks for posting. Will be tackling my leak soon, armed with this know-how.

@lesy8068 Жыл бұрын

One suggestion was worth everything in this video....use the old seal to hammer against the new. Not doing that is exactly what caused my current leak.

@kylekramer4235 3 ай бұрын

I’ve been trying to fix my leak on my dodge truck for a while. This video is very detailed and helpful. Thank you!

@Tony1775Tone Жыл бұрын

What a great video. Thank you so much for creating this period. We had been messing with A stubborn seal and couldn't get it off for anything. After watching your video and using the heat gun. We got it off in less than 5 minutes.Thanks for your help brother if I ever meet you I owe you a cold beer!!!!

@toronjanahera1143 16 сағат бұрын

You've got it wrong about the copper not showing on the inner bushing, it might be right in some cases but not in most.

@walterlangkowski4723 7 ай бұрын

Sometimes using a spedi sleeve over the yoke works too but on certain T cases it allows the seal a slightly fatter stainless steel surface to to grip.

@robinimpey101 11 ай бұрын

Great video, with great editing, informative & concise! 👍

@dragnblazer 11 ай бұрын

awesome video. Im gonna do this to both my s10s this winter. and replace the speedo garket.

@bena2293 Ай бұрын

Thanks Bro, Great Job love all the Tricks makes it so Easy when you see how it is done. So Cool.

@joegray1155 2 ай бұрын

Exactly what I needed to see. Thanks for posting

@inflikti0n 14 күн бұрын

Thanks

@MadAtMax.300Blackout 4 ай бұрын

Recently bought a 93 with an AT 4l60e. Noticed the smallest drip, tens as small as yours, on the very lip of that tailshaft seal and the seal is dryrotted. Thanks for this video this is good info, hoping I can repair this stuff w/o having to pull the whole tranny

@mattperkins7038 Жыл бұрын

Pretty clean repair. Nice

@ramonbarrios5186 10 ай бұрын

Great job but you said while you’re there the speedo cable housing seal

@joselouru 2 ай бұрын

My only advise would be to put a little silicone around on the outside cover , it will leak from the cover after awhile The metal is old

@metroe2138 Ай бұрын

Can this be the same concept as fixing the main seal leak from my 1984 Buick Regal?

@flatblackhair1 Ай бұрын

Great video

@dalemihocik4732 Жыл бұрын

Nice work. It's too bad they don't make a repair sleeve for the axle yoke like they do for a harmonic balancer. I'm guessing that would make too much sense.

@joeschafer1 8 ай бұрын

I have seen repair sleeves, but they want about as much as a new yoke.

@logix7 Жыл бұрын

you're back! great video of course

@GODSPEEDGarage Жыл бұрын

Thanks! I have been crazy busy with my "day job" and haven't had time to edit videos... it's a lot of work, and I'm dedicated to putting out quality, informative, to the point videos... so editing is important to me. I've got a few more I'm working on so hopefully I'll be posting a bit more regularly 🤞🤞 I appreciate your support! THANKS FOR WATCHING!!!

@bjohnsonmn 11 ай бұрын

Did you drop all of your transmission fluid when you started, or is there only a small amount in the tail housing when you remove it?

@V8Lounge 11 ай бұрын

There is only a small amount in it

@MrSerioLok69 Жыл бұрын

Good video bro. I think that’s my problem with my 400th. One day I drove 60 miles and the next morning my floor was stain with oil and seen it was splattering underneath the car. The drive shaft also has play as I wiggle that rear seal yoke. I have notice the car shaking a bit after driving 30 mil.

@donfullbright8468 7 ай бұрын

Nice instructions.

@yeboscrebo4451 4 ай бұрын

Many thx

@505fastlife6 Ай бұрын

Do all transmissions have a bushing like that?

@rustybumperclassics6342 Ай бұрын

Good video

@steventrombka569 Жыл бұрын

Appreciate the help

@josenavarro5189 4 ай бұрын

Appreciate you bro

@anthony-wo2fs 11 ай бұрын

Hi my name is Anthony I have a same truck you have but I put a new wire harness business stairwell lots of small one but now my signal lights I go to the right and the light goes on to the left and the left like was under the right so what should I do

@aros007z 8 ай бұрын

Awesomeness

@rucker225 Жыл бұрын

I wonder if there’s the same bushing in the transmission tailshaft of my wife’s Nissan NV3500?

@amateurism1 9 ай бұрын

Great video, I’m doing mine, do you recall when yours was apart, if the output shaft on the trans without the slip yoke on was free to wiggle around? I assume yes, without the support of the slip yoke, but I don’t know, any help is appreciated from you or others scrolling through the comments.

@GODSPEEDGarage 7 ай бұрын

I don't remember honestly... maybe others can weigh in

@amateurism1 7 ай бұрын

@@GODSPEEDGarageThanks for getting back to me regardless.

@Moparbarnett88 9 ай бұрын

Will the seal leak if the yoke is too far away due to vibrations.

@Kosova444 8 ай бұрын

what is that bushing called

@at_tro_sizematters 4 ай бұрын

I'm not a mechanic.. so I realize my question is going to be stupid... but would that leak smell like gas?

@brassmule 19 күн бұрын

No. It's transmission fluid.

@codymarschinke9383 Жыл бұрын

What trans is that?

@jorgesoto4847 Жыл бұрын

Looks like a 700r4

@mandoramirez1958 5 ай бұрын

Got the link to parts?

@GODSPEEDGarage 5 ай бұрын

yep! all links are in the description of the video

@louisbowser Жыл бұрын

Wobbldy wobble

@waynegreen6789 Жыл бұрын

Drop drop it like it's hot

@josephbrandt3359 7 ай бұрын

New Subscriber… Great job 👏🏽!!!

@GODSPEEDGarage 5 ай бұрын

Thanks for subbing!

@josephbrandt3359 5 ай бұрын

@@GODSPEEDGarage TH-400 Tail-shaft housing leaked from the two mating surfaces, which were laser straight. I tried using “Permatex” BLACK on one side of the gasket, on both sides of the gasket, followed by a dry gasket alone. Nothing worked! Here’s what did work… I cleaned off both mating surfaces with acetone thoroughly. Followed by using “Permatex” 1-Minutes Gasket Maker. I had a space heater hitting both mating surfaces and the temperature got up to 85*-90* I applied the 1/8” bead as directed Then, mated both parts and torqued the bolts to 22ft-lbs. No gasket was used, so this is metal to metal (aluminum) contact. I then placed the space heater under the truck where the TH-400 is and put the heater on “HI” Temperature got up to 115*-120*. 36 “HOURS” later, (due to my job) the “Permatex” 1-Minute Gasket Maker did the job. No more leaks, seeps, drips, or runs at the Tail-shaft housing, or the Speedo-Housing either!!! Thanks for your video. Although my experiments took me a month, dropping the tranny fluid 4 times… I finally got it. Hopefully this information I’m providing helps someone. Your video helped me.