Another good video Moose. Your's are the best because you talk to us in plain words and never embellish. Easy to understand and saves us a lot of unnecessary or unprofitable steps in recycling. Good job. Thanks

Hi, this was development of my idea. I am glad this little idea despite a lot of criticizes and negative comments, have blossomed into this system. I have to thank guys at the Mt. Baker for their ingenuity.

I love their channel.

Really enjoying all your video'. Inspired me to scrap again. Learning new and different ways to scrap and make money. Thanks for your willingness to share your experiences and knowledge.

Great video, can't wait for the next. I am subbed to MBMMLLC, they have some excellent crushers and they make them in different sizes to suit their customer's needs. I've watched all of his videos, he'll literally crush anything that's sent to him!

with the black sands , u can put it in a cruciable with borax and melt it then pour it into a cone shaped mold . any gold will be visible at the pointy part once its melted

Excellent vid bud, this is great info to show people who want lots of money for their E-waste, they are blinded by the Midas effect, gold fever, this shows how thin our margin is and what we have to do to get it. thanxs again

Moose great video! What was the overall verdict? How did the disolving of the cone go?

Love your videos Moose. Maybe I'm a pessimist but I find it hard to believe that a mining company whose goal is to make money from gold etc., would provide anything of much value. Maybe they're "true blue" I couldn't say but that classifying table should be able to separate the materials rather well and so would they sell off any material that is really valuable? Also, I have been using Nitric acid, which you can make yourself but concentration it is more difficult, to drop gold from solution. The copper, silver, brass, not sure about aluminum, will be dissolved in Nitric but NOT gold. It will be left at the bottom of the solution as a powder. I usually heat it up a bit to help the reaction. Then I let it cool, filter, and rinse. The solution which is left contains silver, copper, etc. which can then be processed further. Also, the copper nitrate etc. can be decomposed to yield the nitric acid back again. I'm no expert, still learning, but just FYI.

Great series of video. Very interesting but sounds quite dangerous with the fumes and all. Be careful. Did look like a nice paperweight.

Thanks for being honest,I did comment on your last video about this company and point you in the right direction.Its not possible to grind a whole mother board into small enough particles to put straight into water separation.You would need to chop or grind the mixture of glass,plastic,ferrous steel,non ferrous steel,solder to a similar size as the gold bonding wires in the chips.The screen would just get blocked ,Just like you showed in your video,its better to cherry pick and process separately

I bet they snuffer bottled of all the gold bonding wires on the shaker table before they gave it to you

Is a low heat melt on your paper weight viable Moose, 600-700 C should pull a good chunk away then cuppell the remainder?

Great topic moose...I've been panning a lot of black sands and reading about the sands composition and have been finding native platinum and copper sulfides and zinc and calcopyrites anyway one of the books I was reading talks about nitric acid leaches with table Salt as the precipitater.Im no expert my first hydrochloric batch is still unfiltered but loaded with fingers...so basically the black sands are of interest for refining Andi look forward to more videos from you cause you rock

So how do you seporate the gold off the gold plated pins

Helps me appreciate why gold is so expensive.

Have you tried a wire brush wheel or sander to remove the gold from a board? Although dusty, it seems like a transportation/ time saver to give you faster results.

Moose, have you discovered an efficient way to recover gold from the laminated flexible PC boards and flat connector straps?

cool

curious to know if there's gold in the green motherboards etching? I think I seen it was mostly copper, maybe you could do a video with the motherboard completely stripped and ground down maybe even without the solder, I thought of just heating a large plate then setting the bare board on it to scrape off soldier maybe gravity would keep the solder on the plate. 10 or 20 bare boards at once would show some results.thx

I have been stalking up on gold pins and stuff for a little while and am starting to think about refining it. One question thou. When something is plated, is it always plated in 24k or can like 18k be plated? If so, should I be sorting my gold so the lower k doesn't mess with the higher? What k are the gold nuggets that you refine?

Hey moose love ur videos and I just got into gold recovery with phone like I started today and I took apart the phone and now I'm stuck so can u give me step by steps of how getting gold from phones and how selling gold and getting money from them keep up the good work

Moose. I wanted to find out if there is a productive way to clean the power cord ends that have gold and silver on them. All the pins, flat pins, tv/video cords, etc......... thanks for your time.

hi moose is hydrochloric acid 32% ok for the ap methord

Despite the lack of actual gold reclaimed from those samples... pretty cool to mess with those samples. Always a great learning process if nothing else right? :)

Hey moose I work in a gold mining town or small city and they have what is known as a roaster for high sulphides and from what I have heard through the grape vine is it is heated or roasted to about 600 degrees Celsius and then they can do the magic bit with acids and crap which I have no idea on as that is secret squirrel stuff. Ps excellent info from ya vids brud keep it up

use copper sulfate electrolysis of the pyramid to make blister copper, and recover the gold containing sediment, then chemically extract that. You definantly want to be recovering the Copper as it is a sizeable portion of the economic value of the board. Really you need a series of chemical / electrolytic processes. Don't handle that stuff with your bare hands. Cadmium could be an issue.

How much money can i get from a old motherboard like that one you used?

I can tell you how too get the gold out of the black sands ... I hope you did not do anything to them yet ....

hmmmmmmmmmmmmmmmmmmmmmmmm crush up them there LAN plug ends....

Me and all of my drugy friends scrap too. :D

WoW Ok Well Aftr All This & That Ovr Gold, some Gold Refinery Co. is gonna buy yo Scrppn Business out at a rate u dont wanna refuse, u get so far n2 a mattr & yo Career Importance changes & we lose Moose n Scrppn, gone 2 a highr finer material n life. All i can do is Wish Ya Well as i sob off this comment. LoL Stay Encouraged & i Do Wish Ya Well, May Prosperity Be Whatevr u U Lay Yo Hands On

Waste of time lol