Here are some of the tools I used in this video: Wire Rolling Mill - bit.ly/WireRollingMills Combo Rolling Mill - bit.ly/ComboRollingMill Flat Rolling Mills - bit.ly/FlatRollingMills Rolling Work Table - bit.ly/RollingWorkTable Cheap Metal Melting Furnace - amzn.to/2H6IPwf Electro-Melt Furnace - bit.ly/Electro-MeltMeltingFurnace Adjustable Ingot Molds - bit.ly/IngotMold Oxygen & MAPP Torch Setup (Much hotter but tanks sold secretly ) - amzn.to/3pbYVW1 Oxygen Tank Small - amzn.to/3apH7T1 MAP-Pro Gas 2x Small - amzn.to/2KEnxrq Acetylene Oxygen Setup like mine - amzn.to/3ajSGLw Basic Smith Little Torch Five Tips - bit.ly/SmithLittleTorch5tips Rose Bud Torch End - amzn.to/3krLoaF Crucible for Casting - amzn.to/31ARCxr Borax Powder 1lb - amzn.to/2ISMQoA 2 Reversible Wire and Plate Ingot Mold - amzn.to/3aqrzP2 Graphite Casting Ingot Mold - amzn.to/34njuGQ Fire Bricks - amzn.to/2KxvK0P ________________________________________________ If you are looking for more tools and materials that I use, well you're in luck! I made a page on my website just for that. GomeowCreations.com/tools-and-materials GomeowCreations.com/partners-discount-codes *Note* Most of the links that I use that go to products are affiliate link. This means I make a small commission on anything that you happen buy using them. This is at no extra charge to you and this helps support the work I do on this channel. 😁👍 ________________________________________________ Other Ways To Help Support The Channel: My PATREON ➜ patreon.com/GomeowCreations One time support ➜ paypal.me/gomeowcreations ________________________________________________ Instagram ➜ instagram.com/gomeowcreations/ Facebook ➜ facebook.com/GomeowCreations/ ________________________________________________ #pepetools #wirerollingmill #rollingmill #jewellerymaking #jewelrymaking #goldmaking #silversmithing #diy #gomeowcreations

I was around 7 years into jewellery making and the advice a tutor gave me was to try to get the best I could afford. He said if I bought a Durston it would last longer than my lifetime. So far, no regrets and I bought the Durston C100.

I bought a Durston C130 this year and after watching this video, I now want the Pepetools mixed wire mill too. I’ve gotta start saving. 😏 Thanks for the demo. It’s a fantastic machine.

I have several tools that came with a crank. I have since made a wheel of the same diameter. It helps making a more consistant preasure. I have a cheep roller now but plan on getting a Pepe Mill as soon I as I can. I think the combination mill like you showed first would be my best choice.

Now thats awesome!!! I like how it does bezel wire too!!! Very cool!!!

I use a Combo mill from Durston and I absolutely love it. I have a Agile 130. But I'm really interested in all the different wire options. Durston makes a wire only mill but it doesn't offer the different shapes. Great video showing all the options

Just bought the same and also have the 110mm PEPE now the same as your one wire 160mm PEPE and my antique ones 120years old !

Thanks for this vid. I just bought the 160 Pepe wire mill and experimented with it today. Was a bit different for me as my other mill is a Durston flat. Knowing the sequence you just showed really helps (square first). 🙏🙏 Am looking forward to getting back at it and experimenting more after seeing your vid. 👍😊👍

Thanks for sharing. Have fun with your new toy. :)

Combo ingot molds are also good for 1/2 round ingots

Pepe 130mm combo is awesome ❤️

Very nice machine and example of its capabilities, I love using and watching machines work!🏹🏹🏹

thank you

Learning how to use a rolling mill our Rock Club has. This was good information.

Looks like ill be adding 2 rolling mills to my operation once I have the space :P

Hey, good for you for getting sponsored by Pepe. Your videos are great. I bought one of the Pepe mills (combo 110), and I love it. Your videos definitely helped me make my decision, and were informative. It was ~$550 on sale. Glad I didn't get a cheap one.

I use a Blazer Big Shot GT8000 butane torch to melt small amounts of silver.

Such a helpful video thank you - I have this mill, bought recently. Had lots of fun with the profiles, but I'm struggling with the bezel wire - any tips for how to best go about this?

Thanks Meow Meow ! I would like a mill sooooon !

New tool on my wish list!! Thank you for the info!

If you have to start out with square wire, how do you move on to round wire? What size does it need to be brought to in comparison to what size of round wire you need?

I am thinking of buying the little combination rolling mill you have but can’t find any info on the dimensions of it and need to know if it will fit in the tiny space I have. I would be so grateful if you could tell me the width and froth of it and the length of the handle as it extends out either side.

Hi and thank you for sharing- now I need another rolling mill!!!! How do you remove the pickle from your silver before putting through the mill again? sand it off?

I use a simple propane torch without oxygen to melt silver and it works just fine.

You show so many good tools, but I don't even have shafts ... The tool increases the ability to make faster and cooler, but not everyone has enough imagination to use it correctly!

Hello I’m using an economy rolling mill just like the little blue one you have I find it difficult from time to time to make sheets cause I use the ingot mold that make the wires and the sheets but whenever I make a sheet it always seem to be to thick to go through the mill but if I cast it it’s easier but takes me so much time would you mind to do a video on how to make a metal sheet whenever you have a chance

what was that pickling solution and where to get? thank you great vid

what's the dimension of the band shown at 2:40?

Great video.. as always! One question: what would be an example of using triangle wire?

Randy, check out the Paige Tools soldering tips, they work for the Smith Little (others too)! We're talking MULTI-ORIFICE for ALL your tips, superior performance!

Thank you. Rolling mill machine .is it suitable for silver only. cause I want to start with aluminum wires as a start ?

I have a question, once you use a crucible on copper metal, can I use the same crucible for silver and gold? Or do I have to use different crucibles for different precious metals? Thank you again👍

you only need to quench in water and dry not pickle.

Do you do diamond setting at all ?

I dont quench in pickle

Looking for a mill to better expand my buisness

Hi have I made the wrong decision buying a rolling mill as a beginner? Help

you Can't use a propane torch to melt silver ?

Maybe it's very silly question, yet... How can you make same profiles, not "solid",...but "hollow", I wonder...

Once you focus on the flailing hands it's all you see.

Why pickle after annealing, if you'll be annealing again before soldering? I am unsure about when to pickle. Which is a fairly funny sentence taken out of context, but true non the less. Not trying to criticize what you're doing, just wanting to understand why you're doing it.

30 dollar draw plate or brand new 700 dollar rolling mill

let it cool SLOWLY (vs. dipping into liquid) to make softer/flexible, otherwise it hardens it!

Those rolling mills are expensive as ... , pepetools and durston rolling mills are like easy over 1000$ for someone who doing this for living its cheap probably, but for a hobby jeweler its unreachable.

Wrong once, wrong twice.

We w éfr

like number 420!!!!

damn it sucks being broke but wanting to do things that require large investments

Too many words! This, like any of the other videos, seems intended to stretch the video for more and more ads but it doesn't add to the instructional content.

Those animated hands ...

I am sorry it does not take an hour it only takes 10 to 15 minutes!!!