DIY Stainless Steel Exhaust tip Make an exhaust tip like this at home, without any special tools. All you need from tools are a welder and an angle grinder.
Пікірлер: 41
@protomanialabАй бұрын
You are a wizard 🧙🏻♂ This is a good lesson of mechanical handicraft! Thank you friend!
@tonimerklin122Ай бұрын
Thank you for your videos and knowledge!
@jean-pierrepannierdesrivie4406Ай бұрын
You are a very good teacher !!! Bravo !
@azharsalim2028Ай бұрын
Great job... however, in the first part of the laying out process, he need not take the trouble to calculate all those "pies" etc.... just take a piece of paper and wrap it around the pipe and mark the circumferemce. Then just divide it by the number you want.
@irvingcobianАй бұрын
Good info!
@berndheiden7630Ай бұрын
Easier: just fold the paper 3 times in half to get the 8 stripes!! 2/2, 4/4 and 8/8! No calculation at all!
@guytech7310Ай бұрын
Pretty Neat method. Thanks for sharing!
@JoliettesParadiseAdventuresАй бұрын
Looking great!
@muhammadalfin2891Ай бұрын
Very neat workmanship, greetings from Indonesia
@arneminderman3770Ай бұрын
Wow! ❤❤ great video
@thedude5869Ай бұрын
Nice job !!
@michelbalts6064Ай бұрын
Magnifique....merci
@user-rp6sv2hx5sАй бұрын
👍 super Video 👍 thank you
@moarif9139Ай бұрын
that's awesome
@Rainer1992Ай бұрын
Das sind einfach skills Wahnsinn ❤
@charlescamilleri3323Ай бұрын
Very nice and prof. job weldone
@nickmarshall9192Ай бұрын
Excellent work Not perfect But still excellent 👍👍👍
@RustyInventions-wz6irАй бұрын
Nice work. I’m sure I’ll have to do it myself at some stage
@GPGarage1Ай бұрын
Thanks
@dimashilov8139Ай бұрын
видео немного затянуто, но познавательно 👍
@stiefbeen22Ай бұрын
Another approach could have been using a cone of cardboard, like kids have on their head on their birthday. Using the larger diameter as the base and the smaller one up as high as the length you want between the 2 pipes. Cut it at that point horizontally and use the lower part on the stainless steel. Only welds will be on each end and the closing. Less welding, less polishing.
@oliverstaudinger5003Ай бұрын
Genial Einfach=Einfach Genial
@kevinsmith3935Ай бұрын
Lovely bit of work , what are the discs you used on the angel grinder to clean welds and Polish the stainless please
@GPGarage1Ай бұрын
Thanks, for cleaning the welds I use Pferd Polifan A40 SG, after that sanding discs p80, p150 and p240 than polishing with some "no name" stainless polishing kit (polishing pad and blue compound)
@Unboxing.ChannelАй бұрын
😍😍😍😍😍😍😍😍
@sebf2226Ай бұрын
👍
@luigiesposito4543Ай бұрын
Belloooooo❤❤❤❤
@AoW3_Dag_05Ай бұрын
🎉
@user-hg4bk7ok4oАй бұрын
Красиво. Но почему без поддува?
@denisyakob5546Ай бұрын
Мне понравилось
@naboru1000Ай бұрын
Ну что я могу сказать? Ахуенно! Надо попробовать так же. А то я постоянно пытаюсь найти переходники для трубы в нужный мне размер!
@mrmiron4936Ай бұрын
По ходу чел не в курсе, что 1 клетка равна пяти мм 😅😅😅
@chipcity3016Ай бұрын
Ebay $5
@ianrace4066Ай бұрын
A cheap pipe expander is easier and doesn't take 8 hours of Fab and you don't need a welder.
@GPGarage1Ай бұрын
Of course, there is an easier way to do this, but this is a DIY project that anyone with a welder can do. Also in this case the difference in pipe diameter is 30mm, so cheap pipe expanders would hardly do the job.
@MasterPKWАй бұрын
А то что заржавеет через полчаса никого не смущает?
@GPGarage1Ай бұрын
No, it won't.
@cecilandrews7479Ай бұрын
In the time it took you just to do the math I ordered two for $9 each stainless steel. My labor loans worth more than that
@hellkell8693Ай бұрын
So what.
@brianfreeman367620 күн бұрын
It's about using tools and fabrication. There's going to be a time when the part you want isn't available on line, what do you do now?