Grom Dyno Jet QuickShifter - Installation Video and Setup

No video

Grom Dyno Jet QuickShifter - Installation Video and Setup

Рет қаралды 31,328

HardRacing

Күн бұрын

Пікірлер: 32

@vanstergrvanliangas7798 Жыл бұрын

Same here, spent hours on dynojets site trying to figure out how to activate my new quickshifter on my GSXR with a PC3 and I couldn't find anything! Thanks for the help Bro

@alski95 4 жыл бұрын

Dude thanx a bunch!! Can’t believe that I’ve searched for Dynojet help in so many ways for my cbr1k and finally I get it with a grom video lol thanx again bro ride safe ✌️

@bulldogwoof6954 5 жыл бұрын

Thank you so much, just had this setup installed on my Yamaha MT-07 and was wondering how all this worked.

@HardRacingPerformanc 5 жыл бұрын

Once you have a quick shifter, you will wonder how you got by without one.

@tariqorozco43 6 жыл бұрын

Please, don't ever, ever EVER ever, let this guy make another video. He takes one minute to give 10 seconds worth of information

@joebobbyrobot 5 ай бұрын

I'm trying to find one for the aracer stand alone on driven tt rearsets.

@SystemAdministrator1 7 жыл бұрын

Super cool video. Well Done.

@HardRacingPerformanc 7 жыл бұрын

Thanks for the post.

@framurray5282 5 жыл бұрын

Great video..will help me set mine up.

@HardRacingPerformanc 5 жыл бұрын

Thanks for your feedback we appreciate it very much

@framurray5282 5 жыл бұрын

just one question you might be able to help me with if you don't mind....I have a pc3 and not a pcv on my 04 busa ..is it the same process as your video to install....havn't put it in yet so any info would be great....thanks.

@matthewmosca3984 6 жыл бұрын

Thanks for the walk through. I tried to test my dynojet quickshifter while on the rear stand. Went a couple thousand RPM above the minimum rpm and shifted through a couple gears. Doesn't seem to be killing the ignition/fuel. Do I need to be close to or at full throttle in this scenario to test it?

@HardRacingPerformanc 6 жыл бұрын

M Modo, put the KILL Time up to 3 second. Lower the "Min RPM" to 2000 rpm .......... put it on the stand, and go over 2000 rpm and press the shifter slowly. It should stall the motor.

@jarrodcapone8617 Ай бұрын

Will this work for a 22 cfmoto Papio 125?

@HOTSHOT-ls1bc 8 жыл бұрын

Ronnie 💻 needs ☝️ of these

@shahsbk11 7 жыл бұрын

Hi , is that possible to D.I.Y the pit limiter ? thanks.

@john-martin 5 жыл бұрын

Does this work for the grom with the power vision 3???

@jesusmartinez2233 3 жыл бұрын

Could you use this with Rc Mini 5? or does aRacer make one?

@HardRacingPerformanc 3 жыл бұрын

Unfortunately, no. As explained in the video, this Dyno Jet QS can only be used with a Dyno Jet PCV. aRacer makes their own version of the QS.

@RohitRoy-ti9qn 5 жыл бұрын

What is the price of this shifter. Is this eligible for duke 390 2019 modle

@shawnnicholson8778 4 жыл бұрын

How do you get to the software put of the pc5 on computer? Is that something you have to download or? I have everything plugged in and ready to go. Just need to figure out how to turn the quick shifter on

@saleshardracing1561 4 жыл бұрын

correct. It's FREE Download from Power Commanders website.

@OntarioAndrews415 8 жыл бұрын

Hi, is there a way to adjust the clutch lever on a GROM? The fiction zone is way too much; the lever is almost fully out before engagement and I think it should be or would be better more at 60%. Thanks!

@HardRacingPerformanc 8 жыл бұрын

+Ontario Andrews Unfortunately, that's the nature of the beast. It has very little movement before it's disengaged. You could loosen the cable if you want more lever movement without doing anything.

@OntarioAndrews415 8 жыл бұрын

Thanks. I just want it to engage sooner.

@HardRacingPerformanc 8 жыл бұрын

+Ontario Andrews Could help to get Stiffer Clutch Springs store.hardracing.com/cart.php?target=category&category_id=2681.

@OntarioAndrews415 8 жыл бұрын

Thanks. Ummm ....I don't actually own the bike yet. Just asking before hand. :)