SUZUKI GSXR 1000 K5 & K6 CLUTCH REINSTALL USING GENUINE CLUTCH KIT GSXR 1000 K5 HOW TO
Пікірлер: 37
@ericbusa7 жыл бұрын
Thanks bud, for all your help, now I know how to do it properly
@777Ruffdriver7 жыл бұрын
ericbusa Thank you i'm glad I could help.
@777Ruffdriver6 жыл бұрын
YES YOU SHOULD LEFT WITH 2 PLATES ? It was some time ago since did the clutch 2.6 or 2.0 2.3 which go on the end,you do mean the still plates
@tufftalk6 жыл бұрын
Should I have 2 plates left over (Goo)
@aaronibarra7325 жыл бұрын
Where did you get that back fin above the back tire looks nice?
@777Ruffdriver5 жыл бұрын
Power bronze UK thanks for watching the video.
@jpich857 жыл бұрын
Sorry mate which way did that spring go in? The second large washer that goes in the back of the basket. Cheers
@777Ruffdriver7 жыл бұрын
CURVE WAY FACING THE ENGINE JUDER SPRING.
@jpich857 жыл бұрын
+777ruffdriver nice one mate
@spenny768 Жыл бұрын
hi the last metal plate how do you no which one to use is it the 2.0mm or 2.6mm standard suzuki kit thanks if you can remember
@777Ruffdriver Жыл бұрын
When you take yours used Clutch plates see what is stamped on the end plate or measure, with Vernon caliper, has used in the video hope that helps .
@spenny768 Жыл бұрын
@@777Ruffdriver hi thanks i will just copy the old clutch ill measure with vernier but as i have bought suzuki why would it use two thickness also i think if i have to measure the whole stack do i include the hub also ha nowts never straight forward cheers tho pal
@777Ruffdriver Жыл бұрын
No problems thank you for watching.
@gatyaagg7317 Жыл бұрын
Thanks for help Bro! Nice job but never use clutch. lever from e-bay. This can destroy your new clutch.
@mikey.2687 Жыл бұрын
So there is a specific order to installing new clutches?
@777Ruffdriver Жыл бұрын
I would say take the old clutch out in the order, it was put in and copy, and reinstall, the new one as the old one came out. Just make sure that the new clutch plates are left overnight in the same grade oil you use for your bike. and measure with the Vernon caliper the end plate because they very, go to the library, you may be able to pick up the manual for the k5 k6 Suzuki 1000cc. This install was done a few years ago and I had no trouble with the clutch after the install. I’ve since sold the bike to a motorcycle dealer and purchased a Hayabusa. Thank you for watching the video. I hope this helps.
@777Ruffdriver7 жыл бұрын
I would say no but if you strip your clutch out see if they match and if they do they fit that's all I can say mate, i'm not professional mechanic just a novice? But personally I buy a new set of plates for a GSXR 1000.
@777Ruffdriver7 жыл бұрын
Once you have tightened adjuster in the clutch housing and backed it off make sure you lock off the bolts behind the adjuster so it is set, and adjust the cable under your tank take some of the slack then look at your clutch lever roughly how do you had it before
OMG... You put the clutch plates in wrong.... The small notch on the guide tabs are supposed to be alligned and will create a oil channel for the oil to escape.
@10mm693 жыл бұрын
It will work but for how long is the question
@lriper4702 Жыл бұрын
The service manual doesn’t mention anything about alignment…
@folerx6 ай бұрын
where we can see this in video?
@FuturisticViper2 жыл бұрын
what brand is that digital caliper tool?
@777Ruffdriver2 жыл бұрын
SORRY FOR THE LATE REPLY THE MAKE ON ITEM IS LASER- THANKS FOR WATCHING.
@justadi917 жыл бұрын
Hey bro can i put clutch plate 2004 gsxr1000 to 2006 gsxr1000 ?
@lriper4702 Жыл бұрын
At 26:00 you mention the three dots. But at the original Suzuki service manual, nothing is mentioned. Which manual are you using?
@777Ruffdriver Жыл бұрын
Suzuki, GSX, 1000 k5/k6 Haynes manual uk.
@lriper4702 Жыл бұрын
@@777Ruffdriver ok, thank you mate! The original suzuki manual is not very analytical on this subject…
@777Ruffdriver Жыл бұрын
@@lriper4702 so thank you for watching my video , I hope it has been a help to you it was sometime ago ,since I’ve done this clutch. I sold the bike 4 year ago and traded it into motorcycle dealership, and purchased my second Hayabusa Gen 2 from them ,the one use advertise my channel.
@lriper4702 Жыл бұрын
@@777Ruffdriver your video is the only one on KZfaq specifically for th k5 and it is great for someone who is not a mechanic. Yes, it was very very useful!
@rayray-ed3jp5 жыл бұрын
you didnt put oil in before you started engine,,look at window
@user-ic1pm6uo7w5 жыл бұрын
lol you're right
@adrianmuller71173 жыл бұрын
dude u know, that u dont see any oil in the window while the engine is running right? ;)
@MJ40FR6 жыл бұрын
tu as fait une erreur les disque lisse il faut aussi les laisser tremper une nuit dans lhuile
@mmm4638 Жыл бұрын
No stack height mention? Lol
@777Ruffdriver Жыл бұрын
It was quite a few years ago since I’ve done this clutch, if you google The GSX-R ENTHUSIASTS FORUM And type in model, you will get the stack height I hope this helps. Thank you for watching.