H&R Topper model 88 remove and install trigger

No video

H&R Topper model 88 remove and install trigger

Рет қаралды 24,634

Rusty Guns

7 жыл бұрын

topper model 88 trigger removal and install

Пікірлер: 23

@gregorymiller4905 10 ай бұрын

I'd give you 2 thumbs up if I could. I landed here after struggling for hours watching another video which was a 4 part series. It basically shows how to rebuild everything from the top and it's super difficult. Thanks for the fresh perspective; now I have a plan! That q-tip trick is my missing link. Now I can rebuild the top with the trigger group totally out of the way and all the room the rifle has to offer for my fat fingers to hold the seer up and out of the way while I install the hammer. What a 180. You're a genius for getting that on film. Thank you so much!

@RustyGuns 10 ай бұрын

No problem, i try to make them as short and to the point as i can

@DaveyBlue32 7 ай бұрын

I am in absolute and total agreement Greg and I wish there was a way to get this video to be the first one you find when you are actually trying to get an old topper 88 trigger assembly back together…. Love your little Q-Tip holding trick and I was thinking about trying to make a little pin that exact pin diameter and then I realized how much I was obviously over thinking the whole deal…. I need a new trigger guard as my plastic or whatever they used is broken off on it’s bottom side so it’s not completely surrounding the trigger… not a huge problem but it’s not very good looking in this condition so hopping I’ll see a replacement trigger guard ??

@SaltySatan 3 жыл бұрын

Thanks for this great video. Cleaning up a topper 88 that hasn't been used in 30+ years. Think my mom got it as a kid. Going to surprise her with it and a couple hundred target shells to have fun with.

@RustyGuns 3 жыл бұрын

Awesome, it'll be a great surprise

@jhill7009 2 жыл бұрын

Thanks for the info. I got my great grandpa's topper 88 and it's seen better days. I gotta replace the trigger guard and reblue it. This is very helpful.

@Thirsty_Tree 7 ай бұрын

I'd make a slave pin out of an appropriate sized roll pin. That way when the pins get punched in, it's a close-to-exact fit. Much easier. Keep the slave pin and label it.

@keithlocke2205 6 жыл бұрын

Nice trick with the Q-tip.....going to give that a shot!!!

@RustyGuns 6 жыл бұрын

Thanks, I just found it works easy enough without having to find or make a small metal pin to temporarily hold it.

@keithlocke2205 6 жыл бұрын

I ended up having a bit of an issue with the pieces moving, and used 2 sections of the q-tip shaft, as it fit tighter. But still, it worked!!! Unfortunately, while I now have a nice, shiny new trigger guard assembly, I bent/mangled the damn barrel break lever spring by trapping it under the block, and am waiting for a new one to come from gun parts....(siiiiigh)......

@haroldwolfe1221 Жыл бұрын

Any idea where I can find a replacement metal trigger guard? It is still a mystery as to who did what, but mine got broke, and the broke part vanished. Wife and daughter said they didn't do it, and the dog doesn't know how to lift the lid on the trash can, lol. Great video, BTW. Thumbs up, and all that....

@shawnhedrick3570 10 ай бұрын

I am also looking for the brass trigger guard (and forestock plastic piece) replacements.

@RustyGuns 8 ай бұрын

I would check numrich first. Usually you can find what you need