Haas UMC Series MRZP & Safe Zone Calibration

Haas UMC Series MRZP & Safe Zone Calibration - Haas Automation, Inc.

Рет қаралды 19,571

2 жыл бұрын

In this video, Product Specialist John Nelson walks us through the latest process of setting values for the Machine Rotary Zero Point and Safe Zone positions for the UMC series 5-axis mills.
If you are preparing to set MRZP and Safe Zones on your GM-2-5AX machine then click on the link below to reach the video specific to that machine:
• Haas GM-2-5AX MRZP & S...
If you are planning to run the MRZP/Safe Zone calibration process on a Haas VR Series machine please click on the link below to watch the video with specifics about those machines.
• Haas VR Series MRZP & ...
Click the link to reach the UMC Series web page:
www.haascnc.com/machines/vert...
Don’t miss any Haas videos. Click here: www.haascnc.com/about/Newlett...
Need more reasons why you should consider a Haas? Check this out: www.haascnc.com/whyhaas.html
If you enjoyed this video, please hit the like button and share it with a friend who’ll find it helpful . . . and thanks!
Follow Haas:
Facebook - / haasautomationinc
Instagram - / haas_automation
Twitter - / haas_automation
LinkedIn - / haas-automation
Code: TMEXP60IARHDZ5LD

Пікірлер: 28

@markterryberry4477 2 жыл бұрын

Nice job John! Super helpful.

@tansit2344 2 жыл бұрын

Safe zones prevented my HFO tech from calibrating the OMP40-2 with a ring gauge on the table. Might want to get your documentation out a little better. This was after an OS update bricked my machines 20 minutes into programs and caused the e-stop circuit to quit working. Works again for now, week late.

@user-cz2kp8vo2y 2 жыл бұрын

awesome

@ramonalvarez2022 8 ай бұрын

Thanks for this Great Haas TRT210 zero point Schooling! 🎉❤🎉❤🎉

@richhuntsd12 Жыл бұрын

Thanks John. Very well done video. I was wondering what the procedure is for the center bore if You purchase the pallet pool? Do you supply a male boss to bolt on in order to probe off of or what? I believe there is no center bore on the Haas pallets

@codycollins5370 9 ай бұрын

What do you do if you have a UMC 500ss with a pallet pool? Do I need to remove the pallet pool table to get to the original t-slot table to run the safe zone calibration?

@skarconmachining6567 2 жыл бұрын

How do you turn the safe zones off?

@skipopotamus Жыл бұрын

Turn Setting 408 On, this will reset on a power cycle.

@Coert94 2 жыл бұрын

How often do you recommend to do the finish set? And when does de machine use the safe zones?

@haasautomation 2 жыл бұрын

Coert Lindhout, Good questions. Here's an answer from John: If your parts are coming out good, don’t bother running the template. If you are having accuracy issues when the part is rotated, you should run the template to see if that resolves the issue. You should definitely run the template any time the machine is moved, re-leveled or work is done to adjust the geometry of the machine axes. The machine uses the Safe Zone values all the time, manually jogging or in cycle. Thanks, Haas Automation

@MrPeteRoberts 2 жыл бұрын

Hi guys, I have run the MRZP and Safe Zone templates and have populated the settings 255, 256, 257, 378, 379 & 380 respectively, but I am still able to drive my UMC 750SS machine to enable the spindle to to touch (Crash) the table. Is there an better explanation of what the Safe zones do. Correct me if I am wrong, but I would have thought that it should stop you from being able to allow this. Is there perhaps a setting that turns on and off the safe zone protection which needs to be turned on? Once the safe zones are correct and active, how does the machine react when it detects that the machine is about to exit the safe zone? Does it stop perhaps 6mm away, or some other set value? What tests can be made to ensure that the safe zones are working correctly?

@haasautomation Жыл бұрын

Pete, First off sorry for getting back to you after 1 year! We obviously missed several questions on this video. You've probably figured all of this out already but just in case. #1: Setting 408 will temporarily exclude the tool from the Safe Zone calculation. This setting always reverts to OFF (meaning Safe Zones are active) when the power is cycled on the machine. Contact your local Haas Factory Outlet. It is possible your issue is related to a software version before safe zones were implemented on UMC models. #2: The machine will detect a move that will violate the Safe Zone barrier and give an alarm before the move. It will not start a move that will violate the Safe Zone. #3: Look at Settings 378, 379, and 380. With the cursor on the setting, do you see a Range displayed just below the settings box? If there is no range displayed, the Safe Zones are not implemented in your software version.

@noahduhs1467 Жыл бұрын

Would it be possible to do this video for the VF series maybe VF 2 with a trunnion like Trt 160 on it because we bought a new one but i think the setup is not quiet the same

@haasautomation Жыл бұрын

Noah, Sorry for the very late response. Use the VPS Template titled MRZP Trunnion for your VF-2 with a TRT160.

@clewisatx 2 жыл бұрын

I bought a haas UMC-750. Added Haas Air Vice. Does this mean that every time I run MZRP I need to remove the vice from the table? I ran it before, but now am recalibrating my spindle. I was told by HFO that I should calibrate tool setter, probe, and THEN MZRP. True? I ran MZRP when first got the tool, and have been having great difficulty in getting the air vice to work, and now that it is I don't want to take it off for a while... So short question - can I unscrew ball and put the flat of the shaft of the ball in my air vice and run it, or is that 9.2" from the deck important?

@haasautomation Жыл бұрын

Chris, First off sorry for getting back to you after 1 year! We obviously missed a number of questions on this video. You've probably figured all of this out already but just in case. #1: Yes, this is true. You also need to reset all the tool length offsets and your work offsets after you recalibrate the probe system. #2: Yes you can unscrew the ball and clamp it in your vise as long as you have enough machine travel to probe the ball in all rotary positions used in the MRZP probing program.

@jeremystroobach6999 Жыл бұрын

I have a fixture/sub plate mounted to my plater about 1 inch thick. Can I mount the tooling ball to the fixture plate?

@haasautomation Жыл бұрын

Jeremy, Yes you can mount the tooling ball to your fixture plate.

@ipadize 2 жыл бұрын

why do you put the ball in the center and not offcenter?

@precisionc3656 2 жыл бұрын

How do I get the new templates for my UMC ?

@haasautomation 2 жыл бұрын

Julian vs, Currently, you need a software upgrade to get the new template. Thanks, Haas Automation

@SukhwinderSinghNatt 2 жыл бұрын

I was wondering if anyone knows if haas Toolroom TM-3P discontinued?

@lpfreak1708 2 жыл бұрын

My understanding was it will be phased out and the smaller TM-0 will take it's place.

@CAMER_21 2 жыл бұрын

How to setup 4th axis??... where to take offsets ...? How to take x y z A of 4th axis...?? Where to put offset??? What is difference between 3 axis and 4th axis A rotary axis???... Make detail videos and make playlist ...

@icefishing4046 2 жыл бұрын

Go to tech school

@CAMER_21 2 жыл бұрын

@@icefishing4046 I don't have money.

@threadtapwhisperer5136 2 жыл бұрын

@AvE , lol. Might could render the bumbkefrickery far more skookum.

@andrealmeida3915 2 жыл бұрын

IF YOU CAN MAKE AN ADVANCED PROGRAMMING LIVE TO GIVE A STRENGTH ... THANKS ..MOUNT A WHATSAPP GROUP ..THIS IS A LOT OF USE HAAS MACHINE WHAT YOU HAVE IN VIDEOS ARE BASIC OPERATION I WANT TO SEE WHAT CAN BE DONE ADVANCED WITHOUT SOFTWERE CAM ,,,IF YOU CAN MAKE A VIDEO LIKE THIS I THANK YOU...