Haiboxing 2995 Brushless Motor Upgade

Рет қаралды 6,143

2 жыл бұрын

This is a longer video going over about everything for a brushless swap on your Haiboxing 2995. It's already a great, inexpensive backyard 1:12 basher...this takes it up a notch. I go over a few specifics, I ramble too...so skip around as needed. Let me know if you like me to show you the actual process of swapping it over. Driving video next. It's now 55% faster with the same stock battery. Also, batteries last longer now. Let me know if you have questions.
Time needed if you have everything: 30min to 1.5hr depending on how fast you are. I slowly did it as parts came in.
Tools needed:
Small Phillips screwdriver, electric drill, drill bits (3/16" and 1/4"or so), small hobby saw/hack saw or grinder/dremel.
Here's the Major parts list:
- 12" long or so zip ties
- Truck itself: www.amazon.com/dp/B08JZ6PRT8?...
- Bolt/screw kit: www.amazon.com/dp/B093V3CB78?...
- Battery strap: www.amazon.com/dp/B01F7NNVS2?...
- Transmitter & Receiver: www.amazon.com/dp/B00VE3QC7C?...
- ESC & Brushless motor: www.amazon.com/dp/B07SSTB8TR?...
- Correct pitch spur gear, stock 16 tooth: www.amazon.com/dp/B0006O7U5I?...
- Correct pitch spur gear, slower 15 tooth: www.amazon.com/dp/B001BHEL0Q?...
- Correct pitch spur gear, faster speeds: www.amazon.com/dp/B082FM5PYP?...
- Replacement center diff/driveshafts: www.amazon.com/dp/B08JG55WV7?...
- Shock upgrade I recommend: www.amazon.com/dp/B08FYLJVNJ?...
Haiboxing, Bezgar, Laegendary, DEERC, Hosim, Redcat, Arrma, 2995, bezgar 1, bezgar 2, bezgar 3, bezgar 4, bezgar 5, bezgar 6, bezgar protector, HM121, HM101, HM124, 18859, 16889, 9145

Пікірлер: 38

@zipzip8239 Жыл бұрын

excellent vid, thanks for making it

@thuhintimidator Жыл бұрын

You are welcome. Thanks

@Ssquatch_28 2 жыл бұрын

I made the same mistake with the gears! Just returned them today Great vid and build 👌🏾

@scottsarchitecturehildebra1761 Жыл бұрын

Great Video!!! Thanks, these truck are great…..

@RoadsideRC 2 жыл бұрын

Thanks for the info! Subscribed!

@thuhintimidator 2 жыл бұрын

You are welcome. Seems like quite a few folks were unsure how to do this as it's not a big name car. It's not so bad really.

@Duhg26 Жыл бұрын

I just ordered this. Hopefully it’ll be a good Rc for my dogs to Chase.

@ChiefRickyRC 2 жыл бұрын

Yup make sure the motor shaft on the brushless motor is long enough. Nice upgrade! Cool trick you can swap the rear suspension side to side to have the shocks on outside of suspension. I think it helps the look

@thuhintimidator 2 жыл бұрын

Awesome!

@thuhintimidator 2 жыл бұрын

Seems like you said something about silicone earplugs...but I can't find the comment. Are you talking about firming up the F/R differential balance? If so, I've heard about that but never did it.

@jaybringus6818 Жыл бұрын

@@thuhintimidator works really well. Just use on center diff.

@juniorgarcia3588 Жыл бұрын

What grease did you use and where to get it I did this set up and now need new front tires does wheelies happy with the set up

@thuhintimidator Жыл бұрын

I just used a heavy duty tractor grease that I use when I grease the tractor. You could use wheel bearing grease from an auto parts store or from a tractor supply/farm store.

@keldonator 11 ай бұрын

Good video. I ordered a 3300kv brushless motor... Now I'm wondering what pinion size I should get. I had intended to use the stock one but sounds like it won't fit. My motor is same size as one you used. Maybe with lower kv I should increase to a 17t or something. Any recommendations?

@thuhintimidator 11 ай бұрын

Ha, I wish I could recall. It's been a minute. Can't remember if higher or lower kv gets ya more rpm or more torque. You won't be lacking on power any direction you go on tooth numbers. Larger will be higher speed in total.

@KlunkersKustoms 2 жыл бұрын

Ours the ESC died with in 5 minutes of use, swapped the Esc, Tx/Rx , with hobby grade stuff, but now put a cheap Brushless system in it

@thuhintimidator 2 жыл бұрын

Yeah this one wasn't bad to swap. It's overpowered, but much improved over stock.

@KlunkersKustoms 2 жыл бұрын

@@thuhintimidator it's a ripper now lol, great video

@johnporter1613 2 жыл бұрын

How did you use a 15 when the mount only allows for 14 or 16

@thuhintimidator 2 жыл бұрын

I drilled the mounting holes out a little bit to give me more adjustability

@farmoboy83 2 жыл бұрын

Hello, since you look like to have a lot of experience, can you tell me what parts will fit hbx 16886 1\14 scale? PArts not available anywhere but i suspect it shares parts with other hbx models or even other brands.

@thuhintimidator 2 жыл бұрын

My experience really just comes car by car as I mess with them. I have a little more experience with the Bezgars. Much of this is trial and experience. Not many parts available. I myself would wonder if parts from the 18859s would swap over. That or the bezgar 1/12 scale. What are you looking for?

@thuhintimidator 2 жыл бұрын

Also, Amazon prime is a good resource as you can return things that are incorrect.

@farmoboy83 2 жыл бұрын

@@thuhintimidator nothing In particular since nothing has broken yet but would be nice to know where I could get parts is something fails. I have a blackzon 1/16, same as hbx 16889 and I bet the motor is the same as well as diffs even though this has them in metal and blackzon are plastic. Maybe parts from 12885 or 901a would fit...

@johnporter1613 2 жыл бұрын

There are parts on Amazon and AliExpress or bangood all you need to do is use the part numbers in the Manual

@linh811 Жыл бұрын

is there room and mounting for larger pinion gears? thanks

@thuhintimidator Жыл бұрын

If you drill out the mounting holes for the motor into slots, you can change the gear on the motor to smaller/larger

@linh811 Жыл бұрын

@@thuhintimidator thank you for the quick reply !

@thuhintimidator Жыл бұрын

@@linh811 happy to

@aureliobenavidez8442 2 жыл бұрын

The shocks you have in your description fit even thought they are 1:10 and the car is 1:12?

@thuhintimidator 2 жыл бұрын

One thing to realize with these chinese rip-snorters... the physical size difference between a labelled "1:10" scale and "1:12" is very very little. In fact, they often build upon the chassis of each other. So back to your question, absolutely those will fit. They may lift your rig up a little, but not a lot. I run them on my Bezgar 1:12th brushless rig that is very similar. I use 30wt oil from Losi. Hope that helps.

@anthonyfootit4579 2 жыл бұрын

What servo and size did you use?

@thuhintimidator 2 жыл бұрын

The stock servo is a 3 wire and still works fine with the aftermarket controls. So, the stock one. There are good replacements out there though

@Ssquatch_28 2 жыл бұрын

May have missed this in the vid, but do you still have use of the truck's LED lights with the motor/esc upgrade?

@thuhintimidator 2 жыл бұрын

Fair question. I did not try to retain lighting. Might be possible, but I was focused on the drivetrain.

@Ssquatch_28 2 жыл бұрын

@@thuhintimidator Thanks!!

@bluddywulf6796 2 жыл бұрын

all you need to do is wire it to the fan output plug on the esc .simple

@Ssquatch_28 2 жыл бұрын

@@bluddywulf6796 with my newer build that is not an option. I actually just ended up getting a new light rack that will connect directly to my new reciever. I couldn't find the right connectors to get the stock lightning with my new brushless motor/esc combo. If I missed something feel free to add input.