【Harley-Davidson Dyna】Chrome switch housing & levers, handlebar grips, regulator cover installation

Рет қаралды 31,829

2 жыл бұрын

Installing the chrome switch housing, chrome levers, handlebar grips and voltage regulator cover.
For Harley-Davidson Dyna motorcycles Low rider
Chrome switch housing kit
part number: 70222-96B
www.harley-davidson.com/us/en...
Custom hand lever kit
part number: 45075-07
www.harley-davidson.com/us/en...
Chrome and rubber handlebar grips
part number: 56263-96A
www.harley-davidson.com/us/en...
Dyna voltage regulator kit
part number: 74667-06
www.harley-davidson.com/us/en...

Пікірлер: 19

@motorpsycho2989 2 жыл бұрын

0:32 Clutch lever replacement 1:23 Brake lever replacement 1:52 Right switch housing & grip removal 3:01 Right switch housing & grip installation 4:35 Left switch housing & grip removal 5:40 Left switch housing & grip installation 6:51 Old & new comparison 6:58 Regulator cover

@houndsmanone4563 Жыл бұрын

Nice work. I'm considering installing the same for my 09 RK. Full-watch. 👍🏽🤠 4/7/23

@FranBunnyFFXII Жыл бұрын

Ohey, I have those Bezels on my fat boy's front lights too. They look awesome when riding and off the bike.

@motorpsycho2989 Жыл бұрын

Awesome!

@frankvilla1573 8 ай бұрын

For real? The important fit parts are not shown, your gloves and the words on the screen are in the way. I cant see what you're doing when you install the brake switch or control switches

@josephpuderer1368 Жыл бұрын

What was the stuff that you squeezed on The Handlebar before you installed the grip. Was it glue? And how much glue does it take?

@motorpsycho2989 Жыл бұрын

Yes, it’s glue. Not so much is needed since the genuine HD accessories are all nice snug fit.

@josephpuderer1368 Жыл бұрын

@@motorpsycho2989 thanks for coming back at me. When I changed my handlebars I put them back together again and did not use any glue. Actually it really didn't need any glue I think I pushed it all the way on but it is on and it's not going nowhere. So thank you very much for the information. Live long and prosper.🦊

@lnsdetailingmechanical5440 Жыл бұрын

Do you have a close up of the brass piece that goes were the frint brake switch is. Mine fell out and now have no brake light😮

@motorpsycho2989 Жыл бұрын

Sorry, I don’t.

@lnsdetailingmechanical5440 Жыл бұрын

@motorpsycho2989 all good i figured it out, its actually a brass wedge that goes between the front break switch and inner housing of the switch block 👍

@danielfransson9380 6 ай бұрын

@@lnsdetailingmechanical5440 mine fell out too. don't know where it should sit! Do you have a picture or video of where it should be?

@lnsdetailingmechanical5440 6 ай бұрын

@danielfransson9380 no sorry i dont but if you put the brake switch in first and and push the switch towards the flat part on the brake lever there will be the smallest little gap between the back side of the brake switch and the housing. It slides in there. Does that make sence at all 🤔 i wish i did do a video of it as I've had heaps of people ask me about it now but once i finally figured it out I got the sucker in there. I could probably grab the old swich block and out and point out were it goes if that helps at all ??

@karenswinford5954 8 ай бұрын

To put my chrome housing on is there any sodering done?

@motorpsycho2989 5 ай бұрын

No soldering necessary.

@karenswinford5954 8 ай бұрын

Hello

@user-rv2cy3rv4e 2 ай бұрын

So i mean yea, like you did the process. But i might as well been leaning over someone's shoulder n just watching. ** Also prob shouldn't wait til your on the second switch cover to THEN tell people to make sure they've removed the main fuse. But you failed to mention all the tedious steps IE: and which way to reinstall the break button wedge. Or the fact you need to hold onto your brass connectors that go over the throttle n idle cables, unless they bought new ones. Ok im done.

@dwaynemiller6830 5 сағат бұрын

This video is about useless. Show what you're putting back in and where. Like dealing with the clips on the throttle cable to hold them in the housing.