In this episode I install the 5th gear mainsheet bearing and the 5th gear. Then the gearbox is fitted into the case and bolted in.
Пікірлер: 28
@olenairsoftguy88Ай бұрын
awesome channel, you are very meticulous and very well spoken, hell yeah man thanks for the info!
@BlackDirtCyclesАй бұрын
Hey, that's very kind of you to say. I'm glad you enjoyed the video. 🖤CutWeldRide🖤
@chrisvanalstine8136 Жыл бұрын
Thank you so much for the build series. Especially this video and the shift linkage setup. My 96 1200xlh transmission ate the dogs off 1st and I had to do a total overhaul and new clutch. Without your videos It would've been a long struggle but instead was an enjoyable build. Thank you so much
@BlackDirtCycles Жыл бұрын
Thank you so so much for the kind comment. I'm so glad that you found the video of use. 🖤CutWeldRide🖤
@raydouglas58962 жыл бұрын
That 5th gear went in real easy, nice job.
@BlackDirtCycles2 жыл бұрын
It slipped in so easily. Almost thought it had gone in wrong if I'm honest.
@garywallace95252 жыл бұрын
Another great video dude.
@BlackDirtCycles2 жыл бұрын
Thank you very much dude. Appreciate that
@thenegus19902 жыл бұрын
Interesting and thorough as always
@BlackDirtCycles2 жыл бұрын
Cheers dude 👍
@Rattydo2 жыл бұрын
Awesome video!
@BlackDirtCycles2 жыл бұрын
Thanks dude. Appreciate the kind words. 🙏
@ryanbaldwin96232 жыл бұрын
Great job 👏🏻
@BlackDirtCycles2 жыл бұрын
Thanks dude 👊
@CultofRust2 жыл бұрын
Nice one. Very clear.
@BlackDirtCycles2 жыл бұрын
Thanks boy 🤘
@ei571710 ай бұрын
I have an issue of the right side foot peg thread have cracked, and it seems like the hole goes right through to the transmission. can you point out which hole it is from the inside?
@juanojeda2982 Жыл бұрын
Does the 5th gear inside the case move at all mine feels like it’s very hard
@williamardenjr1169 ай бұрын
That's stupid luttle flimsy clip broke on mine. Bike has been down since. Even the shofter shaft stripped. Been trying for 3 weeks to gwt this shifter to work
@playbravoАй бұрын
I have a 2019, trap dor transmission. Do you know if i can take off and re-install that bearing without take apart all engine??
@BlackDirtCyclesАй бұрын
Thanks for taking the time to comment on the video. It means a lot. Unfortunately, I'm not familiar with this year, so I don't want to advise in case I'm wrong and cause you to damage your pride and joy. 🖤CutWeldRide🖤
@playbravoАй бұрын
@@BlackDirtCycles thank you for the answer 🙂👍. It's a 2019 xl 1200cc. I heard a tickling noise when is Stop in neutral coming from that bearing, when a pull the cluch lever it desapear. I have change everything in primary side, clutch basket, bearings, hub, tensioner shoe, primary chain, new oil, new clutch barnett extraplate carbon, well, i did everything i could. But the noise seem to be from the side of the 5th gear bearing. I'm desperately
@ottoritterpangtay8661 Жыл бұрын
Can I change the bearing at the end of the transmission without removing the transmission?
@BlackDirtCycles Жыл бұрын
Which end of the transmission? Trap door end or sprocket end?
@danroy1925 Жыл бұрын
What year is this sportster engine?
@danroy1925 Жыл бұрын
Since the primary and trans are all one unit, can you do this job without having to pull the whole unit? or is pulling the unit required?