Incision S8E 80mm/90mm Shocks Step-by-Step Instructions

Incision S8E 80mm/90mm Shocks Step-by-Step Instructions - Vanquish Products

Рет қаралды 14,443

2 жыл бұрын

The Incision S8E shocks are included on Vanquish Products Phoenix Portal as well as sold in pairs. This video outlines how to assemble these shocks as well as how to rebuild them.
Snap Ring Pliers: amzn.to/3FNds2m
Buy on Vanquish Products: bit.ly/3G72tCe
Buy on Amain: bit.ly/3b0cFhb
Follow My Social Media!
HarleyDesignsInc
Facebook.com/HarleyDesignsInc
Harley's Thingiverse: bit.ly/2YKOhes
My Camera/Production Gear:
Sony A6400 Camera: amzn.to/2K0ixt1
Sigma 16mm F1.4 Lens: amzn.to/2Y9TQj2
Audio-Technica AT875R Microphone: amzn.to/2YcVqR7
GoPro Vlogging Rig: • GoPro Hero 7 Vlogging ...
Zhiyun Crane V2: amzn.to/2Eo3Zjc
MacBook Pro 15in 512gb: amzn.to/2DGgBRQ
Samsung T5 500gb Hard Drive: amzn.to/2CxRcN4
DJI Mavic Drone: amzn.to/2EGw2un

Пікірлер: 42

@jeanpmagnanig 2 жыл бұрын

Great video Josh, love the fact that first e-clip flew like 90% of the times and became part of that other dimension.

@BrazinScaleRC 2 жыл бұрын

Yep, I saw that E-Clip go flying! Nice one...

@emmonsracing3470 2 жыл бұрын

Beat me to it!

@HarleyDesignsInc 2 жыл бұрын

That was simply a video edit so I could get it seated properly :) Dang things are slippery!

@grrfy 2 жыл бұрын

I always try to do c-clips and things like that inside a pillowcase cover, saves hours looking for them on the floor, .... granted wouldn't be ideal for filming

@HarleyDesignsInc 2 жыл бұрын

I like snap rings too but they definitely aren't as user friendly to the general consumers since they require special tools. Thats why these shocks come with the lower cartridge pre-assembled.

@jerryvolpini7987 2 жыл бұрын

I use a similar technique when assembling my shocks. As well, I use a small dowel, cut to size, that I insert in the shock and then install the cap - this keeps the shaft from moving up and down during assembly and only takes a few extra seconds. 👍

@MrSneakyGunz 2 жыл бұрын

Josh, could you please point me towards any aluminum, adjustable spring collar, that will fit the stock SC8E shocks on the VS4-10 portal shocks?

@slowcrawler2695 2 жыл бұрын

No SNU! 😢 All good! But definitely look forward to those on Tuesdays 🤣

@wrrccreations443 2 жыл бұрын

I had a heck of a time getting collar to thread on properly. It would go straight then want to skip.

@jaylite2826 2 жыл бұрын

I got so frustrated with that, I just went to LHS and picked up a different set of shocks.

@wrrccreations443 2 жыл бұрын

@@jaylite2826 Thank you I thinking I was only one

@davew1285 2 жыл бұрын

Another informative video. Thx. Any news when the straight axled Phoenix is going to drop?

@HarleyDesignsInc 2 жыл бұрын

No straight axle Phoenix is announced. The Phoenix Portal is brand new, so there will not be another release any time soon.

@xRougeStatusx 2 жыл бұрын

Any word on a restock of the Phoenix?

@alenharris1152 2 жыл бұрын

Is it just me or is Josh using dental picks? Lol creative

@HarleyDesignsInc 2 жыл бұрын

You can get a pack of 6-8 different styles on Amazon for just a few bucks. They are larger than dental tools, and can be very handy for RC.

@nickmyers5036 2 жыл бұрын

Is 30 weight a good weight for these shocks/ rig? I just got this kit and haven't built the shocks yet. Love the channel, man!

@HarleyDesignsInc 2 жыл бұрын

30 is great if you like to drive slow and technical. If you drive with more speed, I like to go up to 60-80.

@jerryvolpini7987 2 жыл бұрын

Ideally, all manufacturers should be using small screws to hold the piston on the shaft, then no need for e-clips! And, c-clips, just use a threaded cap and no need for them, either! 👍

@HarleyDesignsInc 2 жыл бұрын

Threaded lower cartridges take up more space is all, so this style is used for maximum shock stroke and consistent compression on the lower seals. Lots of different schools of thought in shock design for sure.

@rushbransonsm 2 жыл бұрын

Are these shocks available for purchase on the vanquish site? I did some searching and looks like only the older version is available on the site. its hard to find shocks with a bleed hole in cap.

@HarleyDesignsInc 2 жыл бұрын

Complete sets aren’t available yet but will be.

@shredcraftrc Жыл бұрын

Mine leak so bad right out of the box, tried rebuilding and they still are wet after every run. Not sure what the issue is since people rave about these shocks but I had to take them off my Phoenix because of how bad they leaked.

@The_RC_Guru Ай бұрын

They all leak and have since the beginning yet they still keep selling them with no acknowledgement.

@KevinRCMan 2 жыл бұрын

You uhh... You find that e clip??

@boosieboo497 Жыл бұрын

Where are the rubber o-rings in the kit? I didn’t see that part in the instructions either. Mine leak like crazy and now I know why . Thought this kit was perfect but see they’re are things missing. You’d think if you spend that much $$ everything would be included

@billderas3420 2 жыл бұрын

Oops! I put the shock pistons in up-side-down. But, they were still working very well. Will need to fix that. Did I do that on my Pro build too? Dang!

@HarleyDesignsInc 2 жыл бұрын

It’s not critical at all, just moves the support as far up as possible. Not worth pulling the shaft thru the seals to fix.

@mikej8832 2 жыл бұрын

Man.... No ShockGate incident... Been so long since you tasted some shock fluid.

@visionary_rc7987 2 жыл бұрын

What shock oil is included in the kit?

@HarleyDesignsInc 2 жыл бұрын

30wt.

@odomandr 2 жыл бұрын

Which knipex do you like?

@HarleyDesignsInc 2 жыл бұрын

I added a link in the description.

@odomandr 2 жыл бұрын

@@HarleyDesignsInc thank you, always nice to have another quality tool

@drowildcat2960 Жыл бұрын

I purchased snap ring pliers through link did not work I had to buy this one works alot better . KNIPEX 44 11 J0 Internal Snap Ring Pliers-Forged Tips

@jamesdash1906 2 жыл бұрын

Hey Harely, how about helping a long time fan out ???? I'm disabled and can't afford to buy a new crawler,do you think you could help out ??? And no this is NOT a joke.

@drowildcat2960 Жыл бұрын

I purchased the snap ring pliers through the link after trying to remove the snap ring they did not work The tips were too big and square the pins that going to the snap rings were too short for me to get in the shock body there is a much better set you can order This is the part number I'd recommend getting this instead of the one that you have posted .. KNIPEX 44 11 J0 Internal Snap Ring Pliers-Forged Tips

@HarleyDesignsInc Жыл бұрын

That's super odd, thats the exact same part number that the link takes me to and that I use. Are you sure they didn't send you the incorrect version?

@drowildcat2960 Жыл бұрын

@@HarleyDesignsInc The one you have linked is the KNIPEX - 48 11 J0 Tools - The better set is Kinpex 44 11 J0 Forged tips they're a lot more round just a couple numbers off 44 to 48 but they work really good buddy A lot more round at the tips and a lot longer pins they fit really well in the shock body