HealTech QuickShifter Easy (iQSE) Install on Yamaha FZ1

Рет қаралды 144,481

6 жыл бұрын

The Healtech QuickShifter Easy (iQSE) is a magical little box that enables you to carry out super fast full throttle clutchless shifts.
More exciting than that, you can also control and setup the quickshifter via Bluetooth with the app, allowing you to easily make tweaks and adjustments on the fly!
Healtech have kindly provided me with one of these little smile-makers, so that I can try it out and show you guys what it's all about!
More info about the iQSE Quickshifter Easy here:
www.healtech-electronics.com/...
So join me as I fit this wonderful little gadget to my Yamaha FZ1-N.
00:25 - Intro
01:05 - Fitting the Wiring Harness
08:12 - Opening the Quickshifter
08:32 - Fitting the Gear Shift Sensor
11:15 - Connecting the Wires!
11:49 - Mounting the iQSE unit
13:12 - Bluetooth Setup
14:17 - Setup Wizard
16:20 - Settings rundown
Thanks again to HealTech for the amazing support!
[[------ NEW AMC STICKERS! -----]]
Black Camera: bit.ly/AMCamblk
White Camera: bit.ly/AMCamwte
Black Mount Yin: bit.ly/AMCmntyinblk
Black Mount Yang: bit.ly/AMCmntyangblk
White Mount Yin: bit.ly/AMCmntyinwte
White Mount Yang: bit.ly/AMCmntyangwte
Black Set: bit.ly/AMCsetblk
White Set: bit.ly/AMCsetwte
FULL SET: bit.ly/AMCfullset
-----------------------------------------------
Get AMC's ALBUM here: bit.ly/AMCcd
(includes channel theme tune: 'Happiness')
-----------------------------------------------
Support me through Patreon: www.patreon.com/andymancam
-----------------------------------------------
Stuff I use:
Leathers: Jacket: goo.gl/5zg5Ao
Trousers: goo.gl/n9jy6N
Sony X3000 Action Camera: amzn.to/2GtfwyT
Sony X1000vr Action Camera: amzn.to/2iIMIKU
Sony AS200vr Action camera: amzn.to/2mvfYX9
NOCO XGB3L Battery Pack: amzn.to/2wiK4k0
NOCO XGB12 Battery Pack: amzn.to/2oPCC9M
Ishoxs Bullbar: amzn.to/2gnLz8r
SW-Motech 'City' Tank Bag: amzn.to/2xxNfmh
SW-Motech 'Blaze' Panniers: amzn.to/2Iv3SEI
3M Dual Lock: amzn.to/2KZRLRo
Wera Tool-Check Plus ratchet set: amzn.to/2nqq6OB
Leatherman: amzn.to/2nfNMrx
Gear Gremlin Cable repair Kit: amzn.to/2nfI2ya
--------------------------------
Say hi on Twitter: @Andymancam
AND Instagram: @Andymancam
--------------------------------
I am a participant in the in the Amazon EU Associates Programme & Amazon Services LLC Associates, an affiliate advertising programme designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.co.uk & Amazon.com

Пікірлер: 298

@richardbanks725 Жыл бұрын

Again another brilliant video by you - as well as the rotor I fitted this heal tech gear indicator following your perfect instructions and was dead easy - massive thanks 👍

@Blipthethrottle726r 3 жыл бұрын

I know you don’t have this bike anymore but I’ve just bought one and been watching all your videos on it, gonna be coming back to these mod videos as I add stuff to it over time.

@HepcatHarley 6 жыл бұрын

Recently fitted this to my FJR and without even bothering with the app settings it worked flawlessly :)

@AndyManCam 6 жыл бұрын

Excellent! I've had it in defaults due to lack of time and it's also been great. I happily stand by Healtech stuff. Great products with awesome support.

@nathanpickett2221 6 жыл бұрын

Just looked up this quickshifter thanks to your video, actually sells for a reasonable price compared to others in the UK. Look forward to the review vid!! 👍

@AndyManCam 6 жыл бұрын

It is very reasonably priced. And given the features it has and how well it's been working just on default settings, I'd say it's worth it.

@phillipsirmais828 6 жыл бұрын

Had mine for two years now. Not a problem so far and so much fun.

@AndyManCam 6 жыл бұрын

Thats very good to know. Cheers Philip! No surprises lurking around the corner!

@paulwyand6204 4 жыл бұрын

I like that MGA! I worked on a 59 in high school working on the restoration. We did everything except the body work and the upholstery.

@AndyManCam 4 жыл бұрын

She's a beaut. I would entertain the idea of seeing if I could do something with it. But the I've met the guy who owns it twice and he looked at me like I fell off of the bottom of his shoe!!

@kumarathomassen5031 5 жыл бұрын

Hey andy man, I fitted one on my fz1N and I used your video and it works perfect and it's realy sick on the road, I love it and I wished I had fitted it sooner. I use your video's a lot and you got a brilliant voice mate. Good luck and I hope to see more of your vids soon.

@AndyManCam 5 жыл бұрын

Thanks Kumara! It’s an awesome piece of kit, I love mine too! Sure you’ll have plenty of fun with it and I hope the same with the videos!

@philliptapec8670 2 жыл бұрын

After watching it made me fully understand on how to install and set up this device into my yamaha r1 thank you soo much for the time to record this video to help people like me 👍👍👍

@AndyManCam 2 жыл бұрын

My pleasure, happy to help! Enjoy!!

@b_reyo 5 жыл бұрын

What a great video ! Thank you very much for your work man 🙏🏻

@AndyManCam 5 жыл бұрын

Cheers! Thanks for watching!

@highlandriders9696 6 жыл бұрын

Looks a great product. Seems simple install too. Looking forward to test ride

@AndyManCam 6 жыл бұрын

Very simple mate. Surprisingly so. I've got a few tweak tios direct from Healtech so hopefully should soon have it singing on song!

@russelllocke7180 6 жыл бұрын

Very interesting, love the ‘quick’ hands. Let the riding begin AMC.

@AndyManCam 6 жыл бұрын

Cheers Russel! It's going well so far. Loved it in the UK. Sounds good on the vids too!

@ianlawrie919 5 жыл бұрын

I was confident I could do this procedure myself till you progressed onto the Blue Tooth bit when I spontaneously wept. Great vid Sir

@AndyManCam 5 жыл бұрын

Haha! It's really not too difficult, honest!! The app takes care of most of it, and I've been using the default settings created by the wizard since the install and it works great!

@davrac2008 3 жыл бұрын

what a 1st class video, thank you. im looking for a quick shifter for my 2015 FJR, as i have god used to the quick shifter on my 2021 GSA

@AndyManCam 3 жыл бұрын

I don't think you could go far wrong with this one. Easily the best bang for buck!

@TheDonInLondon 6 жыл бұрын

Great video as usual love the corrections you added :) really need to get one of these for my new bike! Pleased it works so well...

@AndyManCam 6 жыл бұрын

Cheers mate. Yeah i didn't want to send anyone up the garden path with bad info! 😄

@Ninja1000sx. 6 жыл бұрын

Hi AMC I fitted one of these last year to my Triumph sprint St, it's preformed flawlessly ever since. One thing I did was set the rpm cut off to its minimum, this allows me to clutchles shift even in light traffic conditions

@AndyManCam 6 жыл бұрын

Hi Arron. I'm really impressed with it so far too! I found it a little clonky at low revs, but that was without trying to fine tune. Quickshifts in traffic woud be nice!

@02bigkev 6 жыл бұрын

Well done. Looking forward to the ride vid.

@AndyManCam 6 жыл бұрын

Cheers kev. Hopefully won't be too long!

@jonathanwrightwright3113 4 жыл бұрын

Never left a comment on anything before , having bought a bike with one on and watching your really brilliant video it has helped me understand everything about it , like I said brilliant , thank you Andy 👍🏻

@AndyManCam 4 жыл бұрын

Many thanks Jonathan. Very happy to have helped!

@Viper6-MotoVlogger 6 жыл бұрын

Apart from the 8mm to 10mm fiasco, that is quite a cool device and easy install. The Bluetooth connectivity is brilliant. Ride safe mate.

@AndyManCam 6 жыл бұрын

The Bluetooth is a real winner in my book. I hate delving under the seat more than i have to!

@ninjanelly3506 6 жыл бұрын

Looking forward to seeing the results on the road ol chap 👍🏻😎

@AndyManCam 6 жыл бұрын

So far it's been very good. I've just gotten some tips from the manufacturer, so hopefully will get it shifting perfectly soon!

@kevmcdevitt8755 2 жыл бұрын

i enjoyed this video, very well done. now i'm ordering one for my zx6r.

@AndyManCam 2 жыл бұрын

Cheers Kev! Happy quickshifting!

@MrBeerscuits Жыл бұрын

Great video, I own a FZ1 for about 3 months now, time for some mods hehe

@BIG-K 6 жыл бұрын

That is a very neat install and a slick demo, Andy. I hope your eating proves the pud, or something like that. Meanwhile, I wonder if they do one for my SWM..... 👍

@5valvepete618 4 жыл бұрын

Good tubing man like umall. I've had the same universal tank prop come to hand so many times👍

@AndyManCam 4 жыл бұрын

Thanks very much Pete. I've got many 'universal' tools! 😜

@johnsenkiw430 4 жыл бұрын

Well I must say it was straightforward to install with the help of this video, thank you . Two adjustments on the Bluetooth app and I am doing full throttle no clutch blasts ...unreal !

@AndyManCam 4 жыл бұрын

Awesome! Yeah it's a great piece of kit and childsplay to set up! Keep on shifting John!

@johnsenkiw430 4 жыл бұрын

Andy Man Cam Hey there me again . Now you have me thinking about lowering the bars an inch . I’m trying to decide if I should go the SV 650 rise with the stock bars or go all in with Rizoma risers and Rizoma Fatbars . I saw your vid installing your black, wide bars and I thunk you mumbled something about ...was it worth the effort . Thoughts .? John in snowy Denver Colorado USA

@gatito339 4 жыл бұрын

great video made,thank you.

@AndyManCam 4 жыл бұрын

Thank you too! Glad it was helpful!

@streethawk_1617 6 жыл бұрын

i love this bike ! have it for 7 years now... went from FZ1n to fazer 1000 got a fairing from the US ! look even better... have a full yoshi system with pc5 and a pc QS its a blast on the highway...

@AndyManCam 6 жыл бұрын

It's an awesome machine. I can see me having mine for the same length of time! No interest in putting all that horrible plastic on it though! ;D

@streethawk_1617 6 жыл бұрын

doesnt look quite so bad ! have set you pics on your insta page ! check it out !

@streethawk_1617 6 жыл бұрын

plus help reduce windblast aswell !

@motoventure_6938 6 жыл бұрын

Look forward to the test video to see the results and your thoughts mate!

@AndyManCam 6 жыл бұрын

Me too! So far VERY impressed. Few install changes to be made and then I can get on with it.

@mattfireblade9136 5 жыл бұрын

It's no FZ1, but here is a full throttle test on a cbr1000rr: kzfaq.info/get/bejne/hrKTddGcm7Sqm30.html

@leduaracosta1569 3 жыл бұрын

Amazing video mate and now I understand much more the app as I didn't have a clue hahaha 👍🏽

@AndyManCam 3 жыл бұрын

Glad to hear it! Cheers!

@showtime7979 4 жыл бұрын

Glad to see this video was thinking to put one on my suzuki hayabusa you just confirmed it thanks, and you just gain a sub you have great videos 👍🏾

@AndyManCam 4 жыл бұрын

Thanks Show Time and welcome to the team! I've been loving every minute of having the shifter on the FZ1!

@thelikeablerider8800 6 жыл бұрын

Great install! You have awesome electro wizardry

@AndyManCam 6 жыл бұрын

Cheers mate! I got it from my mama.

@reerbaadia1896 6 жыл бұрын

Andy Man Cam My mama only taught me electrolytes from her struggle with weight her whole life.

@stuart0604 6 жыл бұрын

Been thinking of getting one for a while....you just made me order one lol hope it works 😲😉👍

@AndyManCam 6 жыл бұрын

Haha! The mind control is working! I think it's brilliant. And i haven't even started fine tuning the settings yet!

@stuart0604 6 жыл бұрын

I fitted it the other day its awsome fun, hoping to tune it a bit today although it works pretty good out the box

@shergy657 5 жыл бұрын

Great video mate 👍👍

@AndyManCam 5 жыл бұрын

Cheers very much!

@stephenmcqueen4029 6 жыл бұрын

You have sold me, I need one of these on my FZ1 soon.

@AndyManCam 6 жыл бұрын

I can only agree! I love it!

@AndyManCam 6 жыл бұрын

I can only agree! I love it!

@SantaridesaKTM 6 жыл бұрын

Great Video.

@AndyManCam 6 жыл бұрын

Thanks very much Mr. W!

@johnsenkiw430 4 жыл бұрын

Ok ordered one for my FZ ...hopefully the installation goes as easy as yours...stay tuned

@AndyManCam 4 жыл бұрын

Cool, you’ll love it. Fingers crossed for an easy install!

@luigiemotoblog.7700 4 жыл бұрын

Hello Andy great videos you know i have a fz1 motorcycle and your videos have helped me a lot I liked this because it is encouraging me to put a quickshifter to my bike only I would like you to make a video where you see how it works. Sorry but my English is good and I am using a translator. Cheers.

@AndyManCam 4 жыл бұрын

Thanks Luis! Well the shifter is installed in every single video since this one, so you can see it working every time I accelerate. Though maybe I should put together another video actually reviewing the function.

@supra1102 5 жыл бұрын

Dein Englisch ist extrem gut . Mach weiter so , ich liebe deine Videos

@AndyManCam 5 жыл бұрын

Vielen Dank! Werde ich machen. Leider ist mein Deutsch nicht so ganz gut! Läuft, aber wackelig und fehlerhaft! :D

@nemindakarunaratne2291 Жыл бұрын

Thanks a heap for that

@AndyManCam Жыл бұрын

My pleasure! Happy to help!

@valooshelb Ай бұрын

My english is bad, sorry. Your video is really great, thank's a lot ! I've just one question, the cable on the motor and near the radiator, there's no risk to burn ? Cause it really hot at this place, no ?

@christophergothard7277 6 жыл бұрын

Look forward to seeing how well it functions soon. Nice install vid though!

@AndyManCam 6 жыл бұрын

Thanks very much Christopher! It was a pretty straightforward job TBH, given how complicated and hi-tech the product is! Plug in and GO!

@fibroboy1604 6 жыл бұрын

Just about to stick one on my R1 this week.

@AndyManCam 6 жыл бұрын

Very nice. Even without fiddling, it sticks a fat grin on my face every time!

@fibroboy1604 6 жыл бұрын

Andy Man Cam I have one on my r6 track bike and it’s so much fun on track. Not sure I’m any faster right enough 😂

@wookie153 6 жыл бұрын

Looking forward to the test video. Lots of good audio please as I love the way bikes sound going through the box (insert joke here) with a quick shifter fitted.

@AndyManCam 6 жыл бұрын

You and me both mate! I'll do the best i can. I agree though, i love the sound of a 0.7 second shift!

@favian3380 4 жыл бұрын

@@AndyManCam test video never came?

@simuppal2439 4 жыл бұрын

Hello Andy hope you are doing well i bought an used fz1 N 2008 and it has quickshifter on it from healtech but i connect bluetooth app on it what should i do to make it work it is connected and it shows red light when the ignition is on but doesn't shows green light.

@northernninjarunner5506 4 жыл бұрын

If you hadn’t got the gag the beautiful assistant is actually me 🤣 🤣 🤣

@AndyManCam 4 жыл бұрын

*Disclaimer: 'Beautiful' is a flexible and often inaccurate term.

@Gregory_Kousman_8 Жыл бұрын

Hello my friend I would like to ask you? The quick shifter use in the gearbox for Up&Down or just Up? Thank you

@garthhowe297 6 жыл бұрын

It will be very interesting to see how reliable the shift sensor is in the long run.

@AndyManCam 6 жыл бұрын

Very true. And that's what I'm here for!

@fersbk 5 жыл бұрын

excelente !!!!!

@AndyManCam 5 жыл бұрын

Thanks very much! :D

@Diego87 5 жыл бұрын

si la moto es de 1 cilindro (ejemplo ktm rc 200 o 390), ¿qué se hace con el segundo conector de inyector, se pone el plug que viene para taparlo, se deja libre, qué se hace?

@Ya-8OY-Tim Жыл бұрын

Would this near enough be the Same for the fz6?

@rohitnarayan3966 4 жыл бұрын

Nice video! Let say you don’t want to use the quick shifter, can you use the clutch to shift with out installed jumper?

@AndyManCam 4 жыл бұрын

Thanks! Yes you can use the clutch completely as normal.

@johnmangsx 4 жыл бұрын

Hey man awesome job! Where did you get the little carbon front fender extension

@AndyManCam 4 жыл бұрын

Thankd John! It was from ebay. A little company in Spain I think. Cactus composites or something like that.

@Silbermorfar71 Жыл бұрын

Hi Andy Man, i know you don't have the FZ1 anymore, but i saw the vid, class one and want to hear you, if there was any problems with the QS anytime? I want to buy one too for my FZ, but had some big issues with my Blackbird, so just wanna get some input 😊 Keep up the good work, greetings from Denmark👋🏼👋🏼

@AndyManCam Жыл бұрын

Hi Andreas. The only issue i had was that I cracked the sensor by tightening it too much when i adjusted the gear lever later on. It would sometimes do strange things when it was really wet. But Healtech very quickly diagnosed the problem and sent me a replacement shift sensor. Otherwise, all smooth sailing!

@Knighthawk916 6 жыл бұрын

I reckon youre from the planet healtech ;>)

@AndyManCam 6 жыл бұрын

Wouldn't be a bad planet to be from! All that gadgetry! 😍

@AndyManCam 6 жыл бұрын

Wouldn't be a bad planet to be from! All that gadgetry! 😍

@cornish_boy6235 6 жыл бұрын

Have been waiting for this, do you think healtech will do any discount if we quote you?

@AndyManCam 6 жыл бұрын

I don't know. I can certainly ask!

@TheSkidrowww 4 жыл бұрын

hi what are your settings in QS

@vishalprajapati8840 2 жыл бұрын

Great video. Thanks for that. Can I ask a side question what handlebar mirrors you have on that bike?

@AndyManCam 2 жыл бұрын

Thanks! They’re Highsider Ferrara mirrors. Not available anymore i don’t think, but check out www.louis.eu for newer Highsider stuff.

@vishalprajapati8840 2 жыл бұрын

@@AndyManCam Thanks. I bought some Gazzini also from Louis. Unfortunately they vibrate a lot. Do handlebar mirrors generally vibrate a lot, and how are yours ? :)

@stavencapp 4 жыл бұрын

Man how'd you get such a hookup from healtech with only 19k subs. Lucky

@AndyManCam 4 жыл бұрын

What do you mean ONLY 19k?! Ultimately I know the answer. Healtech like the quality of my videos and how I review the products! Good content wins through!

@fabiomarzulli4257 3 жыл бұрын

What are the best setting you ended up to use on the quickshifter for your Fz1? I'm gonna fit an Healtech on mine as well. Thanks for your help... Lamps

@AndyManCam 3 жыл бұрын

TBH, i just left everything on the default Settings, and it seemed to work perfectly.

@bonabry65 Ай бұрын

I bought a 2020 GSXs 1000 from a private party … he had installed the Healtech QS. Although the QS works great when engaged, there are times when after I stop and cut power to the bike, the unit does not engage and connect to Bluetooth once I start the bike back up causing the QS not to work. Can anyone explain?

@dom_petrolhead9165 3 жыл бұрын

Hey man nice video. Im just thinking my bike need the same upgrade. So my question is it still working? How is your feedback after 2 years?

@AndyManCam 3 жыл бұрын

It was working flawlessly right up until when I sold the bike about a month ago.

@bikersquest 6 жыл бұрын

The coils on this bike are real tough to get to, I had to remove some to diagnose a misfire and man was it tough with seized in caps.

@AndyManCam 6 жыл бұрын

I guess spinning them round to plug in a connector and removing them altogether are two very different things! I imagine that would be a bit of a pain in the bottom.

@nac5000 4 жыл бұрын

so you can configure to always have this enabled and you will never used the clutch just on full stops right?

@AndyManCam 4 жыл бұрын

You can, but it gets very lumpy and clunky at lower revs.

@droneshotsetc572 5 жыл бұрын

Where did you get the carbon fiber radiator side covers. I cannot find any to replace mine that are destroyed.

@AndyManCam 5 жыл бұрын

It was from F&F Carbon. Here's the video ;D kzfaq.info/get/bejne/b5OWlLyb1NCzh4k.html

@trykozmaksym 6 жыл бұрын

That's a mouth-watering piece of engineering... But how does that sensor work? I thought it's some kind of piezoelectric... but the way it's mounted - is there some crazy accelerometer/gyro inside?

@trykozmaksym 6 жыл бұрын

Is it possible to disable quickshifting between 1st and 2nd ?

@AndyManCam 6 жыл бұрын

I'm honestly not too sure. I think it deals with compression, or lack thereof. So how much it's being squeezed. I don't think you can disable shifts between 1 and 2. Only below a certain rev range. Though I've found even shifts between the first 2 gears to be far better than expected.

@trykozmaksym 6 жыл бұрын

That thing must be very sensitive because the compression probably changes very little - because of the splines. Have you had any "misfires"? How consistent is the shifting?

@Henka-mxpartsse 3 жыл бұрын

Thanks for a great video! Where did you buy your winscreen? I just bought myself the same bike.

@AndyManCam 3 жыл бұрын

Many thanks! I got it from www.louis.com although i find it quite noisy.

@Wave1dave 3 жыл бұрын

Hi Henrik, I am thinking about buying one for my FZ6. I know Andy didn't like it that much because of the wind noise, I want to get it on my bike mainly to protect all the gadgets mounted on the bars. Do you find it loud and annoying as well?

@Henka-mxpartsse 3 жыл бұрын

Hi! I did not buy a windscreen yet for my bike yet :) maybe latee this summer after ived recieved my license 😅

@Wave1dave 3 жыл бұрын

Guess I'll take the risk then. Thanks and ride safe!

@Henka-mxpartsse 3 жыл бұрын

The same to you! Ride hard but safe!

@ced67660 5 ай бұрын

hello nice job , i have the same bike , is it possible to have your settings ? thank you

@AndyManCam 4 ай бұрын

Cheers! Thats easy. I left everything on default!

@sergiosergio471 2 жыл бұрын

Thank you!! yesterday i buy this QuickShifter for my fz1! how is your feeling when you ride with QuickShifter?

@AndyManCam 2 жыл бұрын

My pleasure, enjoy it! I love the feeling with the quickshifter. Almost like I’m a better rider than I really am! 🤣

@TK1.3.1.2 2 жыл бұрын

@@AndyManCam hi :)…very helpful clip.thanks for the instructions:). Just received my QS…i was wondering about step 6.the sensor setup. Im on kawasaki z1000.and im in Neutral…i need to go to first gear and then do 3 up shifts?,or its ok to set it up when im in neutral and do 3 upshifts. Thanks :)

@luigiemotoblog.7700 4 жыл бұрын

A favor could you send me the model or as I ask to see if I can get it here in Mexico. where did you buy it?

@AndyManCam 4 жыл бұрын

Hi Luis. Have a look on www.healtech-electronics.com/ there you‘ll be able to find the right model for your bike and also see if there are dealers and distributors in Mexico. 👍🏻

@K-carbon 4 жыл бұрын

Great video so easy on your bike on wiring that up on a zzr1400R hell no 😩

@AndyManCam 4 жыл бұрын

Thanks Tom. Yeah I guess thats one of the real benefits of having a naked bike!!

@robsonITALY85 2 жыл бұрын

gruß aus Bremen🖐

@AndyManCam 2 жыл бұрын

Moin!

@comfysofa1549 4 жыл бұрын

Not sure if i missed anything but does this cater for some stuff that needs to stay on? ie a battery backed gps tracker??

@AndyManCam 4 жыл бұрын

How do you mean? The QuickShifter shouldn’t have anything to do with those. I’m guessing that youtube shunted you on from the Thunderbox video? I guess if something really needs to stay on, you’d have to go direct to the battery. Though if it’s battery backed, this means that you’ll not need to worry about it killing your battery. Don’t most trackers last for months before they need another charge?

@comfysofa1549 4 жыл бұрын

@@AndyManCam Heh - yes....ironically ive had a healtech qs for years on my hypermotard....so yes it was in relation to the other video - my apologies...

@TheKiller6364 4 жыл бұрын

Did you have to make any changes afterwards or are the adaptive (automatic) settings fine?

@AndyManCam 4 жыл бұрын

I have had everything on the default settings (adaptive) for the whole time and it works just great!

@TheKiller6364 4 жыл бұрын

@@AndyManCam Ok sounds great, thanks for your reply!

@gregparkes8089 5 жыл бұрын

Hi andy, just a quick one I’ve just bought one of these for my R6 and just want to know does it do down shifts? I know it won’t blip but does it do the ignition cut?... also how did you find out the best kill time settings?

@AndyManCam 5 жыл бұрын

Hi Greg. If your shifter rod is in the right orientation (push or pull, I can't remember) then it will cut the ignition for downshifts but, as you say, it won't blip. This means it doesn't make for the cleanest downshifts and I have found that sometimes it actually kills the ignition at the exact moment I've wanted to blip the throttle. You can install it so that this doesn't happen, and I'll be doing that as soon as it's warm in my garage!! TBH with regards to the settings, I still have everything on adaptive and defaults!! Seems like the best place to start! But the App gives you tips on what each setting does and also what changing the setting will affect.

@gregparkes8089 5 жыл бұрын

Andy thanks for the response... just a last one how do you install it to stop it doin it? Because I’ve seen loads of places that you can put the sensor... FYI I have standard shift in place

@gregparkes8089 5 жыл бұрын

Andy.... when you plugged the piggy back plugs in is their an order in which they should go? Like are they numbered? Also the 2 plugs with the red marker on do they both plug into the same coil pack or do you split them between 2 coil packs? Or and lastly does the red marked ones have a specific coil to go on? Thanks.

@AndyManCam 5 жыл бұрын

As far as I remember, they’re not numbered but they are paired. So each pair has to go to the same cylinder. The marked plugs are important but I forget why. I mentioned in the video somewhere!

@JDRides 2 жыл бұрын

I have a doubt and i would greatly appreciate if you could clear this for me as its kinda eating my brain. i have a 2016 MT09 and I am getting a PC5 since I have got an M4 and a K&N installed. I have also ordered the healtech Qs that you installed. will they work together without causing any issues? should I go for the dynojet qs instead?

@AndyManCam 2 жыл бұрын

I'm afraid I don'T know for sure. If they use the same connections, then you'll likely have problems. I'm pretty sure that the PC5 has pass through connections for extra accessories, but I doubt if they've allowed for other brand stuff to work with tis feature. Maybe an email to Healtech would clear things up. They're usually very knowledgeable and extremely helpful.

@JDRides 2 жыл бұрын

@@AndyManCam I shall do that. Thank you buddy

@AndyManCam 2 жыл бұрын

Hope you get some good answers.

@SINIS0RSA 6 жыл бұрын

In the next episode we will see Andy installing a surface to air missile system on his Yamaha fz1n.

@AndyManCam 6 жыл бұрын

Haha! That would be ideal for the stupid cagers over here that won't let me filter!

@pineapplejelly1005 3 жыл бұрын

How do downshifts work with this?? Can you clutchless downshift because it blips for you or do you need to blip yourself??

@AndyManCam 3 жыл бұрын

You have to blip for yourself I'm afraid. The bike really needs to have a ride by wire system to allow for a blipper.

@davidhall370 6 жыл бұрын

When are you changing the frame , wheels and engine ?

@AndyManCam 6 жыл бұрын

As soon as i find carbon ones that i can afford! 😂

@jamob33 4 жыл бұрын

One question, what is if i shift with the clutch an the quickshift is mounted ?

@AndyManCam 4 жыл бұрын

Hab ja schon direkt geantwortet, aber für das gemeinsames Publikum: Works completely normally with the clutch. Sometimes during downshifting, the ignition can be cut just as you blip the throttle. Happened to me a little bit, but I've since learned to 'ride around it'. You can actually turn off the downshift behaviour completely, but for this you have to mount the shifter sensor slightly differently and turn off some settings through the Smartphone App.

@stuartracing1 3 жыл бұрын

Will it work with GP shifting setup....Reverse shift???

@AndyManCam 3 жыл бұрын

Yes, it works in both directions.

@nathangreen7479 10 ай бұрын

Andy do you rate it, is it something you will add to all your bikes

@AndyManCam 10 ай бұрын

Definitely. I simply didn't fit one to my Honda CB1000R because I was waiting for the warranty period to be up (and then sold the bike!). With the KTM i just didn'T have the time, was about to get one and fit it and some kind soul decided to run in to me in town. Now my replacement bike already has a factory quick shifter fitted. Otherwise, I really rate this quickshifter very highly!

@johnhomles2711 4 жыл бұрын

One thing I wondering if u set a quick ie 7000rpm dose the quick shift still work if revs go past or lower rpm .as it's hard to check rpm when rideing ?

@AndyManCam 4 жыл бұрын

The RPM setting is a cutoff. So it will not work below those RPM but will work above. I have mine set at 3000rpm, so it will not work from 0-2999rpm, but anywhere from 3000 - redline, the shifter will operate as normal. I've never really had to check the revs as you just get a feel for where the shifter cuts in.

@johnhomles2711 4 жыл бұрын

@@AndyManCam top man andy I better get on orderd

@AndyManCam 4 жыл бұрын

No problem! Have fun with it!

@johnhomles2711 4 жыл бұрын

@@AndyManCam 🙂

@SR-cp1eo 2 жыл бұрын

Just so you know, You helped me install this a few days ago. I had a few questions regarding the sensor mounting, watched your video, saw it worked for you, and turns out it worked for me. I did have an issue with it not sensing pressure and ended up shifting a few gears pretty hard without an ignition cut. I played with the sensor pressure settings and ended up setting it to 70%. (it was at 60%). So far, it seems to work since the change, but curious if you've had an issue of yours quitting on you mid-ride?

@AndyManCam 2 жыл бұрын

Very happy to help Sean! I’ve only ever had an issue after washing the bike, but it turns out I‘d overtightened the sensor and cracked the plastic so it was letting water in. Switched the sensor and all was great after that.

@SR-cp1eo 2 жыл бұрын

@@AndyManCam Right on. I tightened the sensor till it didn't wiggle anymore, then did a quarter turn after. Seems to work fine. I think the issue is my foot placement. when I shift normally it's fine, but sometimes my foot placement is slightly off and it won't set off the sensor. I learned that foot placement matters haha! I did a few power shifts that were quite uncomfortable... So far works great! Just rider error. Thanks again!

@AndyManCam 2 жыл бұрын

Good stuff. Yeah I’ve learned that quite often shift problems are more me than the bike!!

@exothermal.sprocket 6 жыл бұрын

Finally a motorcyclist that knows how to speak.

@AndyManCam 6 жыл бұрын

Hahaha! I've been practising since i was little! 😉

@AndyManCam 6 жыл бұрын

Hahaha! I've been practising since i was little! 😉

@exothermal.sprocket 6 жыл бұрын

Whatever system you used, it worked. Others be like, "Uuuugh and and and uuuugh and like, this like, that and like, uuuugh ughhhh, now we can go ahead and.....and then go ahead and......and now we're going to go ahead and...... uuuuugh ughhhhhh. And it was like, I was like, and ." xD

@AndyManCam 6 жыл бұрын

Well thanks for noticing. I try to bring a little bit more eloquence to the field. I also don't see the point in constant cursing. I swear, but you don't need to hear it! Plus my mum watches these videos!

@exothermal.sprocket 6 жыл бұрын

Exactly. Cussing is no substitute for wit.

@justastulpe3265 6 ай бұрын

Hi, does it work for upshift and downshift?

@AndyManCam 4 ай бұрын

It does. But there’s no blipper, so downshifts aren’t rev-matched.

@kyleAsmith19 6 жыл бұрын

How does it work between 1st to 2nd. With neutral inbetween, i wonder how it would react.

@AndyManCam 6 жыл бұрын

As long as you're direct and firm, it's surprisingly good! If you tickle it, you can hit a neutral. But shift with intent and it goes in every time.

@BikenutGB 3 жыл бұрын

@@AndyManCam That's what she said

@omurersin5595 5 жыл бұрын

Hi sir, Did you get any issue with Healtech QS. My friends said that after a while they experienced transmission problems after 1000KM. They said that 3 pieces gears were damaged and had to change. Waiting your asnwer soon..

@AndyManCam 5 жыл бұрын

Hi Ömür. No, I've had no problems at all after almost 10,000km. Everything is still working fine. Is it possible that your friend had the shift interval set too short, so that the power was coming back in before the gear was properly engaged? It would make for a faster shift, but also a much higher risk of the gearing parts smashing against each other.

@omurersin5595 5 жыл бұрын

Thank you very much sir. I have CB650F / year 2016. I always used auto cut off time 80-85 ms. But I always had doubts. Have you every adjust your cut-off times ? Or used the adviced one from application like i did ?

@AndyManCam 5 жыл бұрын

I have the cut off times still set to the default values. Seems to work great.

@user-jc3rv5st3m 3 жыл бұрын

Help, my sense value is always too low I uninstalled the sensor, and squeeze it out really hard, I only get 19% of sense value, I didn't install it too tight. I didn't run the set up at the beginning, is that what causes the problem?

@AndyManCam 3 жыл бұрын

I'm afraid I'm not the expert. Contact Healtech and I'm sure they'll help you out.

@wiley5oh51 4 жыл бұрын

Does it have to be full throttle for the quick shifter to work?

@AndyManCam 4 жыл бұрын

No, not at all. As long as you're accelerating, it will work. Obviously the harder you're accelerating, the better it works. 😜

@DrDonatoDONI 3 жыл бұрын

How about downshifting??

@nathr2012 5 жыл бұрын

Did you ever make a video testing this out and playing with the settings?!

@AndyManCam 5 жыл бұрын

Not yet, but even if I have to do it in driving snow, I’ll have a video finished before christmas!!

@nathr2012 5 жыл бұрын

Andy Man Cam excellent news I look forward to it!

@2WheelsSometimes1 5 жыл бұрын

Thank you very much mate! I just came upon your channel as I am looking to get a Healtech Easy QS too for my MV Agusta F4, which will use the same setup for the sensor as yours. Liked your video, you got a subscriber here for sure. Looking forward to hopefully a great review of it.

@AndyManCam 5 жыл бұрын

Thank you Twowheelshredder! Glad to have you on board mate! Nice bike btw! I bet you’re watching the 44 Teeth BBBI with rigid anticipation!?!

@2WheelsSometimes1 5 жыл бұрын

With great anticipation!!! Don't get me wrong, I am actually a big fan of the 999 styling, but... It's still not an MV.

@MrBenoJacko 4 жыл бұрын

Did you do a testing video? Cant find it anywhere!?!?!?!

@AndyManCam 4 жыл бұрын

No, sadly not yet. Though it’s still on the bike so I’ve been ‚testing‘ in every video since! 😜

@predragsim6356 Жыл бұрын

can it change gears down or only up?

@AndyManCam Жыл бұрын

It can change down and up, but doesn’t blip the throttle, so downshifts will be a bit jerky and probably not great for the gearbox.

@knokcs 4 жыл бұрын

at the very end, this stuff work?? no test of this installation?

@AndyManCam 4 жыл бұрын

This is an installation video. Says so in the title. 🙄. Lots of usage in riding videos after this though. And #SpoilerAlert, it works very well and I love it very much.

@johna6968 6 жыл бұрын

You are an aftermarket add-on God. We're not worthy..

@AndyManCam 6 жыл бұрын

Haha! Thanks Jay! I'm just doing what i can, one add-on at a time!

@Cichymoto 6 жыл бұрын

Can you specify your iQSE settings?

@AndyManCam 5 жыл бұрын

At the moment, everything is on default, with my sensor threshold at 70% I'll be getting into it in more detail soon though.

@Vickeviren 4 жыл бұрын

At what RPMs does it work smooth? :) Thx

@AndyManCam 4 жыл бұрын

I have mine set to come in at 3000rpm. Between 3000 and 4000 it's a tiny bit clunky, but over that it's buttery smooth.

@aleks_the_Great13 4 жыл бұрын

Is this working on up and down shifts?

@AndyManCam 4 жыл бұрын

Yes, although it doesn’t have a blipper so the downshifts can be a bit clumsy.

@nikosdiamantisengravings1242 5 жыл бұрын

Which are the best settings for fz1?

@AndyManCam 5 жыл бұрын

So far I just have the settings on default!

@steve0680657 6 жыл бұрын

Good video. But i found the music throughout a bit distracting. Also you will make more money with a shorter amc intro section. I tend to skip long introductions which i believe could mean KZfaq discount it as an extra view (due to parts being skipped)

@AndyManCam 6 жыл бұрын

Thanks. I'm not sure that 12 seconds is too long for an intro. Not by much anyway! I know what you're getting at though.

@Waleed.alhamidi 4 жыл бұрын

Will it affect the gearbox in the long run?

@AndyManCam 4 жыл бұрын

Impossible to say really. The shifts on the whole are very smooth and so I don't think it could have too much effect. Don't forget as well though, that any extra wear on the gearbox is saved by the reduced wear on the clutch and associated attachments!

@Waleed.alhamidi 4 жыл бұрын

Andy Man Cam ✅👍