Here's How To SPOT BAD SPARK PLUGS!!

Рет қаралды 22,949

Күн бұрын

Here's How To Find Bad Spark Plugs!! Spark Plug Test!! How To Test Spark Plugs!! #sparkPlugs #iridiumSparkPlugs #roughIdle
** I am an Amazon associate. I make a commission based on sales through my Amazon associate links.**
ACDelco 41-103 Spark Plugs: amzn.to/3P7NnCR
Battery Tender: amzn.to/3KQUwoy
Spark Plug Tester: amzn.to/3LfOqhV
www.1roadgarage.com
In this video I'm still trying to diagnose and fix a rough-idle issue I'm having with my 2005 GMC Envoy 4.2L Vortec. I've replaced a bunch of parts and the problem persists.
Today, I've decided to rule out a couple of things. The first is the compression. In previous videos there've been a lot of comments about doing a compression test. In this video, I finally perform that compression test. Secondly, I wanted to rule out the spark plugs. They are an easy enough fix and relatively affordable. Unfortunately, I didn't realize, until I started doing a little research, that there are possibilities of non-genuine ACDelco Iridium plugs out there. So, that led me down a bit of a rabbit hole but I'm pretty sure I've gotten it figured out.
Enjoy.
**This channel is for entertainment purposes only! Do not do what I do. Do not take my advice. I am not a professional. The methods I use may be completely wrong and/or dangerous. Please seek professional help with anything and everything and do your own due diligence (research). Working on cars is extremely dangerous. I am not responsible for any loss of life or limb or property. DO YOUR OWN RESEARCH. THIS CHANNEL IS FOR ENTERTAINMENT PURPOSES ONLY!**
FTC Disclaimer: I am an Amazon associate. As such, I earn a percentage of sales made through Amazon associate links found in the description of my videos and on my website and other places.
00:00 Intro
01:53 New Spark Plugs
03:04 Old Spark Plugs
03:42 Testing Spark Plugs
07:02 Compression Test
08:27 Fake Spark Plugs
10:08 Installing Spark Plugs
10:31 Starting The Envoy
11:20 Conclusion

Пікірлер: 183

@MM_in_Havasu 9 ай бұрын

Jimmy, if you have a good quality scanner tool such as an Autel unit or equivalent, that would tell you real quick during a real time test(engine running)which cylinder is misfiring and how many times. It would also read fuel injector pulse width, and maybe you have an injector tip not spraying as well as the others and goes away when warm. Thanks and keep us posted, Jimmy!

@1RoadGarage 9 ай бұрын

Thanks, I’ll look into it! 👍

@jaycalibre609 5 ай бұрын

What tool do you recommend that allows you to monitor fuel injector pulse/spray? Are there really scan tools that can do that?

@tagnut8382 2 ай бұрын

Hey jimmy, I can only echo mm_in_Havasu’s comments other than, if someone was going to make a copy of item I don’t think they would leave out three little dots, I would be more inclined to think that the oem manufacturing process just doesn’t require them anymore.

@jmm1000 Ай бұрын

@@1RoadGarage any update on the roughness, Jim?

@brettdavis80 8 ай бұрын

For what it’s worth: Anytime you do a compression check you should do a leak down check too. You already have the plugs out. The vehicles I work on I have seen good compression but high leak down (30% or more).

@rmhawk27 9 ай бұрын

Do a simple check of spraying brake cleaner around any intake gasket, Throttle body gasket, injectors, EGR and EGR tube as well as any vacuum lines. If there is a surge in the idle in any spot, then you know you have a leak. Good luck Jimmy

@1RoadGarage 9 ай бұрын

Thanks, gonna do that

@jmac7658 9 ай бұрын

@1RoadGarage Be careful with that! Break clean trunks to Fosgeen gas when it hits something over 300 degrees so be careful. Fosgeen is deadly and there no cure. That's why it should never be used to clean part being welded. Look it up.

@markymark5281 9 ай бұрын

@@1RoadGarageTo piggyback off of this comment, clean the throttle body and change the gasket while you are at it. Also, clean the MAF sensor.

@seansmyers2864 9 ай бұрын

Make sure all wires in the fuel injector connectors are tight and not loose with the harness. Take a multimeter and check the resistance in each of them as well as the coils to rule out any resistance issues. You can check the resistance lf the incectors themselves too. Try running some incector cleaner thru the system. Could always sipe down the throttle body and spray the maf with some cleaner to make sure those are clean.

@jameshall4385 9 ай бұрын

That sparkplug tester is pretty cool. The front two cylinders being slightly down on compression would have me looking at head gasket. I would do a leak down test on those cylinders. If one was down on compression it could be valve related but because its two a joining cylinders i think head gasket.

@1RoadGarage 9 ай бұрын

Man o man. I hope it’s not the head gasket. Are there any other signs that would rule that out? Truck drives perfectly fine. No smoke out the tail pipe. Oil seems normal.

@MN2_Kevin_Hill_1970 9 ай бұрын

Take your oil cap off while engine is running if you have a lot of blowby at the oil fill there is a strong possibility the head gasket is failing.

@jonschwartz9669 9 ай бұрын

@@1RoadGarage open Radiator cap while engine is cold led it get to temp thermostat opens and then look for bubbles this is one way to check fir head gasket or get a head gasket testing kit combustion tester

@ironclaw6969 9 ай бұрын

Ugly thought. On that engine you need to remove the throttle body and intake manifold to get the valve cover/cylinder head. It adds quite a bit of time to the job.

@jacobormsby9241 9 ай бұрын

That would be more indicative of something wrong with the piston rings.@@MN2_Kevin_Hill_1970

@MN2_Kevin_Hill_1970 9 ай бұрын

Try cleaning your Mass Air Flow Sensor, and Do a fuel injection cleaning and a throttle body cleaning you probably have minimal deposits on an exhaust valve and it can't/won't seal 100% and that could be your rough idle. Have a great day and wish you all the best.

@mod_incllc3235 9 ай бұрын

I second this suggestion on this engine.

@JamesSmith-jr2rc 9 ай бұрын

Check your battery and alternator output. They can cause a misfire if one or the other is weak.

@shanebrbich5698 9 ай бұрын

G’day mate! Just watched one of your older videos! Great stuff 👍🇦🇺

@edgardomagana5809 6 ай бұрын

Just started following your channel, thank you for working hard and our jobs easier. God bless

@cnev3824 9 ай бұрын

ive chased that very problem for years on every make since efi became the induction system of all manufactures and it always ends up being a injector with some trash in it , id change the injector for that cylinder or make up jumper rig to trigger it and backflush it

@MrBowNaxe 9 ай бұрын

Boy Jimmy, I feel your pain. I chased a rough idle for months on my '97 Suburban. I see a couple of good suggestions below. As much as you don't want to find out bad news like a head gasket leaking, it's better to find out now than later going down the road at 80! I've been a 1Road fanboy since way back (Cali days), so I really want to know what you find. Can't wait to see what's next.

@jobspeedmms 8 ай бұрын

The video conveyed is very educational, friend, the delivery method is clear and detailed regarding spark plugs

@johngodwin7902 8 ай бұрын

Good video I enjoy and learn a lot from you. Thanks

@josephcullen2512 8 ай бұрын

Looking forward to further diagnostics on the slight misfire or whatever it turns out being

@ryanbandlow533 9 ай бұрын

Hey Jimmy! Love the content! I'm not sure if you have tried it yet but, I know these GM I6 engines are notorious for this issue. The throttle body gets dirty and sticks slightly from what i recall.. as its a drive by wire system it doesn't have a iac motor to take care of idle air.. its definitely worth a shot imo! On the bright side those plugs definitely needed replacement so not a waste of time lol

@Jeffreeebowski 9 ай бұрын

Love your channel Jimmy, just found it and subscribed recently. I've found lots of helpful information for my '97 Chevy K1500. Btw, which video address your final solution to the steering shaft in your '95? I saw the problem you had with the Borgeson shaft and your comment on another channel regarding the Cunningham Machine shaft (which I just ordered). Did you end up going this route and how did it work out if so? I'm sorry I haven't watched all your front end rebuild vids yet which probably address this... my bad!

@KevinNadeau 9 ай бұрын

Thanks for the video Jimmy. I picked up a spark plug tester via your link.

@1RoadGarage 9 ай бұрын

Haha cool! That thing is cool. Saw it in a few other videos and had to have one.

@RoninDosho 9 ай бұрын

Well... When you do discover what the issue is, That'll be one to help others. Case in point, I first started watching when you did your 1st steering bearing video! That was a big help.

@1RoadGarage 9 ай бұрын

Haha! Thanks for watching and following. Yes, I will be continuing to throw parts at it.

@LA_Commander 2 ай бұрын

Jimmy, with a 20 year old vehicle, there are a lot of things which could be causing a rough idle. Since you have replaced the plugs and found no improvement, I would suggest looking at the fuel and air side of the equation. Is the MAF sensor dirty or faulty? The AIT sensor? The coolant temp sensor? Are your fuel injectors dirty? You mentioned that you replaced the fuel pump already. What about the fuel filter? Possibly a vacuum leak somewhere? Rubber hoses age over time and with a 20 year old car it's likely you have a worn out vacuum hose somewhere. But hey, we love watching your videos so keep on wrenching!

@Andy1416 8 ай бұрын

Any updates Jimmy, did you find out what was wrong? Also too, thanks for the awesome videos!

@AntonioClaudioMichael 8 ай бұрын

I would suggest a head gasket being there are a couple cylinders down on compression

@troymecey 9 ай бұрын

I will be buying a spark plug checker tonight. Try a little dielectric grease on the end of the boot when you reinstall them, it will be helpful for removal.

@rufelestrada9791 8 ай бұрын

I've read all the comments through Sept 5, 2023, and I have a similar issue with my Cylinder #1 misfiring randomly, with NO CODES. On my Ford V8 Triton, roller followers go out. They allow the valves to move via a wheel. They pop out of position or freeze/break. I have just opened up my cylinder to examine, and so far no luck. Roller follower looks good. So, we may both have a similar issue, because this cylinder has so much water leakage crustations (like your spark plug) but mine is on the spark plug port, and the buildup is so bad, I can't even get to the spark plug nut area, and I can't remove the spark plug, until I dig/scrape off all the calcium crust. You may also have an internal water leak into the cylinder. Only a Leak Down test will prove it out for both of us....

@autophile-cv621 9 ай бұрын

Good video. The tel tale for me was that #4 spark plug. with that residue on it tells me that there is soomething getting into the cylinder that shouldn't be there. Check for coolant or oil getting into the cylinder. If there is something getting in that shouldn't, it may show up on your O2 readings. That is, of there is enough contamination. Just an educated guess. I hate to see you just keep throwing parts at it. Good luck.

@tossedsalad5532 9 ай бұрын

The real problem with autobile issue. When you think you might have fixed the issue it still needs TLC

@JLC434 8 ай бұрын

Disconnect and cap off vacuum ports on the intake manifold including ones going to throttle body. Had a evap purge valve give me the same issue once, found it by eliminating any possible leak point.

@Sa1imand3rB31 9 ай бұрын

Check your O2 sensor, it should be located near the catalytic converter, when that goes out it would cause rough idle

@garyfeltman4482 9 ай бұрын

If the 02 sensor is bad it should set a code.

@stevelangston2359 5 ай бұрын

Not if it’s slow or lazy when cold

@dontderockmerizz3211 9 ай бұрын

Check the engine mounts. But I’m thinking the throttle body is dirty. Other thing is the intake manifold bolts might be loose. Check for torque. Lastly using brakleen look for a vaccum leak. Remember, no codes tells you it’s not a sensor, misfire etc.

@omaral-enazi6465 9 ай бұрын

I was going to say that 😊

@1RoadGarage 9 ай бұрын

Thanks! Yes, gonna grab that brakleen and dig deeper.

@keithdenner9441 9 ай бұрын

Do you have a new air filter in the envoy? My 2006 ran rough when I hadn’t changed the air filter in a while.

@omaral-enazi6465 9 ай бұрын

It happened to me once in my 2014 gmc Sierra After 125k miles I checked everything it was okay I asked many of my friends and all of them told me to adjust the idie because after 125k and 9 years some sensors are not reading right it was 500 rpm when I was parking . My turner guy adjusts the idle in my truck and it runs fine sens then . I hope this helps you Keep the good work

@hb5914 6 ай бұрын

What is a “turner” guy?

@ChrisTheBmxGuy 9 ай бұрын

I just diagnosed a 16 grand cherokee for a misfire. Plug was ashy just like that #4 plug. It misfired only on cold start and somewhat at idle. Pulled spark plug and checked chamber after it ran for a bit and cooled off. Stuck a bore scope in cyl 3 and found coolant sitting on top of the piston

@1RoadGarage 9 ай бұрын

🤦‍♂️ I might need a scope

@joesilva2628 9 ай бұрын

Should record spark plugs in the dark

@edstevens1435 8 ай бұрын

Have you checked the engine mounts?Try putting in nuetral and see if vibration goes away.The mounts are filled with oil and may show signs of leaking.The passenger side usually goes first being next to the exhaust manifold. You can have youre lovely wife assist in starting it while you film it,then watch in slow mo.If the jolt on initial start get worse with colder temperatures its probably the mounts.Dont forget to check the transmission mount also and buy factory GM mounts. Good luck I hate a rough idle also.

@danh2487 6 ай бұрын

Camshaft phaser or timing chain. I just did my chain and it solved the idle issue.

@DemonicShadow_666 9 ай бұрын

I would look at the intake manifold gasket or the valve cover gasket based of cyl 4 plug covered in fluid. they deteriorate with age and heat since vehicle is from 05. i am going through a similar prob with my 96 gmt. do the ETHER test and see if it revs up around the mating points of the head/valves/motor/intake to get a better idea of where to go, and the plug is not the exact issue but cyld 4 is deff issue. most likely intake/valve cover gasket.

@mod_incllc3235 9 ай бұрын

This is a must do test!

@jacobormsby9241 9 ай бұрын

Have you checked for a sticky Idle Air Control Valve? Does it only stumble at idle or does it do it even when you're on the gas?

@ct1762 6 ай бұрын

with a compression test like that i'd be doing a leakdown for sure. Also did you inspect the IAC valve? I think this engine must have something similar. i'm an outboard mechanic and any idle issues i always check that IAC 1st.

@db5235 9 ай бұрын

I would look at Fuel injectors.. Try some techron fuel additive, it might help and it definitely wont hurt. Not the same beast. but I had a 2012 Cadillac SRX w/150K miles that had very rough idle, thought it was the spark plugs, which they were baked, but ended up it was a fuel injector. Replace one, you might as well replace all of them. Clogged fuel injectors show with a lifetime of cheap Costco gas and the like.

@user-zh4cq4zy1n 9 ай бұрын

Wow Jimmy,,, that's too bad. I know your feeling. Different things but yeah I've been there myself. Good luck

@1RoadGarage 9 ай бұрын

Thank you!

@AntonioClaudioMichael 8 ай бұрын

I would check them to lower compression cylinders do head gasket test for combustion gas in the coolant and even check to see if it had blow by it running and oil cap off you might have a fouled Fuel injector causing less fuel to a specific cylinder Jimmy 12:00 @1road

@qadirali9666 9 ай бұрын

With the imbalance in the cylinders pressure I tried Engine Restore and it balanced my cylinders almost even

@onewheeldeal 9 ай бұрын

Did you you ever change the cam phaser Solenoid, for the variable valve timing? They don’t cost to much and aren’t hard to change. It caused my Trailblazer to misfire when it went bad.

@ironclaw6969 9 ай бұрын

VVT on that engine is exhaust side only.

@ryanelliott2626 9 ай бұрын

Didn't the atlas have an issue with burnt valve seats? Ive never owned one but thats what i always assume when i see one with a rough idle.

@bltoth1955 9 ай бұрын

If it’s rough idling but drives fine, I would be checking for a vacuum leak. Smoke it or spray it to find the leak.

@andrewbarclay6573 9 ай бұрын

Did u gap those plugs to spec?

@atomicdmt8763 8 ай бұрын

perhaps idle air intake? simple swap. changing mine was a huge difference!

@carsrlife 9 ай бұрын

See if there is a TSB on the plug gaps for the trailblazer/envoy... the Tahoe has one for 00-06 to be .040 instead of the .060

@markdickinson6434 9 ай бұрын

Have you checked your screens in the variable valve solenoid

@1RoadGarage 9 ай бұрын

Yes, checked and it looked brand new. Replaced anyways with genuine ACDelco. Still have original unit.

@jimmycorbett4611 9 ай бұрын

You should try maybe replacing the idle air control valve. It could possibly be the source or part of the problem at least. And if it’s not it’s a super cheap and easy part to replace so at least you’ll know that’ll be another thing you can rule out. Only thing is you would probably be running a code if it were stuck open or closed or dirty or somethin, so maybe not it.

@ironclaw6969 9 ай бұрын

That engine has no IAC valve, it simpiy opens the throttle plate slightly to allow idleing.

@stickit2theman1 9 ай бұрын

So I read through most of the comments on here and nobody has suggested a clogged cat yet. I see you have a video (which I haven't watched lol) about the cooling system so I assume you changed the thermostat housing already, and besides this is a 2005 and the stuck thermostat-->clogged cat issues are more likely to happen on 1st gen gmt360s. So basically what happens is the thermostat sticks open which causes the computer to continue running the engine rich trying to get it up to normal operating temp. Normal temp for these are about 200-210. Wouldn't hurt to check your temp gauge cause there are reports of around 160 when the stuck thermostat thing happens so it can go unnoticed. Sometimes you can get a code too but not always! This could be the source of your fouled up spark plugs and potentially could cause catalytic converter gremlins for you in the future! Hope something in this word spaghetti helps you out!

@josegaucin6007 8 ай бұрын

I’m currently going threw the same thing. But it’s my daughters car I’m working on.

@johncollett3648 9 ай бұрын

Did you check the gap?

@ronlind1757 9 ай бұрын

I wonder if you don't have an exhaust manifold gasket leak... can fool you sometimes with a rough sounding idle

@johncollett3648 9 ай бұрын

How long did it take to get 1000 subscribers?

@ourv9603 8 ай бұрын

With the engine running, use a laser thermometer & measure the temp of the exhaust manifold @ the cylinder head. The one which is substantially cooler is misfiring. !

@ChezJ1 9 ай бұрын

I don’t know anything about these new cars, but could it be timing, or is that too old school lol?

@idletime 9 ай бұрын

G'afternoon Jimmy 🤠. Could the issue be an off idle stumble from the idle speed being a skosh too low?. My 98 Chevy Blazer had a very similar issue. It turns out the idle speed was too low and it was causing it to stumble while idling and just off idle until the rpm's picked up and it went away. I turned up the factory idle adjustment screw and even was it maxed out I couldn't get it to idle above 700 RPM. I pulled the idle adjustment screw out of the throttle body, and held the throttle open with one hand while I threaded the adjustment screw in so it was facing the opposite direction and gave the idle set screw more adjustment. I said it so it idles about 950 RPM in park and 750 - 800 rpm in gear. It solved my off idle stumble hesitation issue and now it runs great. I hope this helps my friend 🤠 ..

@1RoadGarage 9 ай бұрын

Thanks for the help. This thing is all electronically controlled. I’m gonna keep digging. Thanks again. 🤙

@idletime 9 ай бұрын

@@1RoadGarage it's all good Jimmy 😇 . Just remember, when it comes to engines not everything can be controlled electronically. My Blazer has the 4.3L fuel injected Vortech that's electronically-controlled. However there are still some things that have Factory settings like the initial timing, throttle blade angle and the idle speed screw that need to be set by hand so the electronics have something to go off of 😋 ..

@chadouellette790 9 ай бұрын

Every time my silverado runs ruff I clean the MAF. Works for me. Maybe you have already done that, I don't know.

@alphasaiyan5760 8 ай бұрын

Intake manifold gasket or worse case scenario is you have a slight leaking exhaust valve on that #1 cylinder.

@JC1993COOL 7 ай бұрын

Does this car have spring loaded lifters?

@atomicdmt8763 8 ай бұрын

verify CLEAN GROUND connections to the engine, elsewhere. Distributor cap / rotor good?

@johncollett3648 9 ай бұрын

Don’t over think it!

@stevesnop3798 9 ай бұрын

these engines are solid but they have a bunch of common issues. Check variable valve timing solenoid, if it does it on a cold start its most likely not that though. also check water pump pulley for side to side play by applying pressure with your hands to the fan. I have seen the water pump bearings go bad to the point the fan wobbles around causing vibration.

@johnfletcher1976 9 ай бұрын

I second the vvt solenoid thing I replaced two on my wife's envoy.

@linceycartwright6220 2 ай бұрын

Try changing the crank and camshaft sensor

@jimmycorbett4611 9 ай бұрын

How badly is it idling. Is there any way you can put it on video so we can see/hear?

@jamothegreat6052 8 ай бұрын

Did you try a fuel injection cleaning? Try running some seafoam. Maybe the valves just need to be cleaned.

@Tombstone226 9 ай бұрын

perhaps an old O2 sensors that is worn out

@ricoselbo6559 5 ай бұрын

Clean the throttle body plate. That gen engine is notorious for crud build up on the throttle body plate and clogging the small gap for idling.

@randyhigginbotham961 23 күн бұрын

That sand textured electrode is atomized oil

@GlennHamblin 9 ай бұрын

Take a look at your injectors. If you can try to test them and look for a good spray pattern and no leaking.

@kikileon2021leonleon-sy2cn 9 ай бұрын

I HAD THE SAME PROBLEM ,YOU KNOW WHAT WAS THE PROBLEM? A SMALL HOSE THAT IS ATTACHED TO THE INTAKE MANIFOLD ,THE CLAMP WASN'T TIGHT AND THAT'S IT .

@Mike-Capz83 9 ай бұрын

you should run a couple of cans of seafoam high mileage to the fuel and see!

@robertofkennedy 9 ай бұрын

Need to use an oscilloscope with an in cylinder pressure transducer

@patrickscott3378 9 ай бұрын

You have to put in a GM timing chain kit.The chains are bad making your ignition timing off.

@1RoadGarage 9 ай бұрын

Hmm. You could be on to something there. Do you have a video link for more info?

@patrickscott3378 9 ай бұрын

Yes watch South Main Auto on you tube .He has a GMC terrain that has the same problem you have.Engine missing and no check engine light on.The fix was to install a new timing chain kit from GM.

@mikeburnett7028 6 ай бұрын

Have a friend with a2011 corvette he’s had to change multiple plugs because they go bad just sitting. His car has less than 10,000 miles. Bet he’s changed 6 of the 8. Drive your cars people

@walterphillips9950 9 ай бұрын

If your fuel trims look good you know for a fact it's not a vacuum leak. Plug a code reader in and check the timing. Does this vehicle have a timing belt or timing chain? Might have something to do with the timing of cams etc...

@1RoadGarage 9 ай бұрын

Live Data From 2005 GMC Envoy! Help Me Diagnose Rough Idle! kzfaq.infotTO8Oc_T1k0?feature=share

@walterphillips9950 9 ай бұрын

@@1RoadGarage Well for one you need a better code reader. And two that live data didn't show ignition timing information. Those fuel trims looked ok to me but it better to have a code reader produce a graph of the live data or show additional items (like timing ignition)

@amundsen575 9 ай бұрын

check for vac leaks, check misfires on scan tool, find the cylinder, then swap injectors to verify injectors after all the car is 18 yrs old

@1RoadGarage 9 ай бұрын

No codes at all. Here’s a short of my fuel trims: Live Data From 2005 GMC Envoy! Help Me Diagnose Rough Idle! kzfaq.infotTO8Oc_T1k0?feature=share

@jewermank8536 9 ай бұрын

I knew from the look on your face... Youll find it man

@antonoudenhoven7573 9 ай бұрын

Always start whit the plugs😉

@IIREAPER925II 9 ай бұрын

Could it be exhaust leak 🤷‍♂️

@jewllake 9 ай бұрын

For as often as you change spark plugs, every 100K miles, and only buying 6 - don't be cheap! Get them from the dealer or auto part store. Way too many counterfeits out there.

@1RoadGarage 9 ай бұрын

I am cheap. 😁

@JJPARRA1974 9 ай бұрын

Throttle body and air intake sensor cleaning..... Problem fixed

@DB-nz9xl 9 ай бұрын

This sounds dumb but get chevron fuel 2 tanks worth and it cleaned up my misfire....I changed sparkplug and wire no help. Fuel with techron fixed.

@Blackopsmechanic338 9 ай бұрын

Drive over to Scotty and have him put it on his fancy scan tool. Lol. Peace

@wiz4020 9 ай бұрын

Are the new plugs made in Japan?

@1RoadGarage 9 ай бұрын

I think it says made in USA from Japanese parts.

@garyfeltman4482 9 ай бұрын

A smoke machine will show any vacuum leaks. I would test the injectors next.

@felipebarron3955 9 ай бұрын

Compa está troca nomás no jala bien, it's a Failblazer, siempre vibra de a madre en los semáforos

@wyatterpp2206 8 ай бұрын

Should have kept the faithful suburban oldies r the best if miles aren’t ridiculous

@iceman45ification1 9 ай бұрын

Something that's good practice when changing your spark plugs is putting a little antiseize compound on the threads. Especially if it's an aluminum head. It'll prevent any galling if you have to replace them again. In any case, nice work Jimmy!! 👍

@1RoadGarage 9 ай бұрын

Hey thanks, yes that would make sense right? A while back I did some research about that and found a few videos from one of which was a spark plug manufacturer that was talking about how the chrome on a spark plug is actually the lubricant. Said that the only time to use anti-seize is when the threads are bare steel.

@iceman45ification1 9 ай бұрын

@1RoadGarage Chrome is corrosion resistant, so that does make sense. Never really thought about that. 🤔

@garyfeltman4482 9 ай бұрын

And boot grease so you won't pull the coil apart.

@punker4Real 9 ай бұрын

most likely a vacuum leak or needs an italian tune up

@1RoadGarage 9 ай бұрын

🤙

@johncollett3648 9 ай бұрын

Check the maf sensor

@1RoadGarage 9 ай бұрын

Oddly, there isn’t a maf sensor.

@michaelmalcolm1985 9 ай бұрын

Them Coil Packs

@nirapsingh9773 9 ай бұрын

Fk acdelco plugs, in my opnion ngk is the best, and i have said it a couple of time now, dump a bottle of seafoam TRANSTUNE, yes transtune in your gas tank when its low, add high octane fuel and drive on highway for atleast 3 hours at 100km/hr speed continuously and then change your engine oil. Ffs just give it a shot.

@MrYoda1982 9 ай бұрын

Fuel filter,vacuum leak,dirty mass airflow sensor, pcv, evap sensor if it has one

@1RoadGarage 9 ай бұрын

Gonna change the fuel filter but have full 50psi at the port. No mass air flow but have already changed every other sensor. All ACDelco.

@MrYoda1982 9 ай бұрын

@@1RoadGaragetime for a smoke machine to check vacuum system, or have you tried all o2 sensors 🤔

@firstlast--- 9 ай бұрын

@@1RoadGarage50psi when it's running normally? Or when it's messing up? Might need to get a fuel pressure gauge with a long hose and monitor it while you're driving

@omaral-enazi6465 9 ай бұрын

Engine mounts check it

@1RoadGarage 9 ай бұрын

I know. I’ve heard about the mounts but this is more than that. The vehicle will also sometimes stall or almost stall. Rough idle but smooth driving and idle is sometimes smoother than others.

@AntonioClaudioMichael 8 ай бұрын

Just because you swapped all the coils out dosent rule them out you could have got What us mechanics call out of the box bad parts NEW Never Ever Works They could of bren faulty coils out of the brand new Box Jimmy @1Road