Thanks I was surprised to not see a grease plug on the side like every other trimmer, Stihl is slipping.
@robertbeck779223 күн бұрын
Hey Hot Wheels Racer...just what I needed to know. Short and to the point. Thanks.
@hotwheelsracer638022 күн бұрын
@@robertbeck7792 No problem Robert!
@mattswaggirt9139 Жыл бұрын
Thank you I couldn't find this anywhere.
@lowellwhite8810 Жыл бұрын
Great info and just what i needed. My example has five years on it and gets warm in use. i thought it was going out and i've been looking to put a greaseable head on it. Thanks for saving me money
@MichaelOnRockyTop4 ай бұрын
Thank you so much for making this brother. It was a huge help
@jimmierev4220 Жыл бұрын
Thanks was helpful had Done the same but wasn't sure if it was right Thanks for the info
@alphaomegalives Жыл бұрын
Helpful video - Thanks!
@WVChad Жыл бұрын
Thanks for the tip. Here’s another tip, remove the guard and put it way, second tip, but an Echo Speed Feed 400 head on and you’re golden. 👍
@hotwheelsracer6380 Жыл бұрын
I personally don't really like to remove guards. It burns them up over time. 1 extra inch of string than recommended is equivalent to about 20 extra degrees on the engine. On the 4 mix engines it causes the cam lobe to melt. And on the 2 strokes ive seen it just slowly kill them over time. Wouldn't believe how much money it'll cost over a cheap plastic guard.
@clevernamehere755927 күн бұрын
@@hotwheelsracer6380 most expensive part of blowing a can gear out of these fs 110s or similar models is literally the tube of red RTV it’s not that big of a deal. It’s a brushcutter it’s gonna get hot. 😂
@grantniels67069 ай бұрын
super helpfull !!!!!!Thanks
@davebrock66188 ай бұрын
Anyone thought about tapping a hole in the side and adding a zerk fitting?
@clevernamehere755927 күн бұрын
Yes but you’re very keen because I thought that was pretty advanced thinking when I saw someone do that recently.
@davebrock661819 күн бұрын
@@clevernamehere7559 if you have info on where to drill, please post.
@leeskipper7041 Жыл бұрын
Thank you
@murkypuddle33 Жыл бұрын
thanks man. how often do you think this needs done?
@hotwheelsracer6380 Жыл бұрын
Once a year
@MrRGiller Жыл бұрын
I believe the echo SRM 225 model, after 50 operating hours, recommends you also Grease the flexible cable inside the shaft. is that a requirement for Stihl as well?
@hotwheelsracer6380 Жыл бұрын
Yes
@MrRGiller Жыл бұрын
@@hotwheelsracer6380 Thank you for the information. I appreciate it
@hotwheelsracer6380 Жыл бұрын
Not a problem
@webberalex9533 Жыл бұрын
What cable in the shaft?
@MrRGiller Жыл бұрын
@@webberalex9533 Some weed eaters have a cable that runs the length of the weed eater shaft to your weed eater head that requires grease. Hope this helps?
@daveschidlmeier64253 ай бұрын
Does this get greese into the gearbox ring and pinion gear? Or does it just grease the drive shaft, gear box square connecting point hole? Does that hole give you access to the gear box?
@optiplexpavel3 ай бұрын
I don't think it does. I looked at mine and it seems that it is sealed and the grease cannot get into the gear head properly. I dn what to do. Maybe drilling a hole in the gear head and fitting a greaser head...
@motoxerdadАй бұрын
@@optiplexpavel haha, I had a feeling this squirting grease down the shaft thing was a scam... I hate having to reengineer everything.... here because they saved 6 cents on a little bolt...
@hotwheelsracer638022 күн бұрын
@@motoxerdad No! It actually does get in there. If you shine a light and look real close down in there you can see the inside of the actual gearbox. I figured this out on my own experimenting with it. Greased it and it quieted my whining gearbox down.
@whereswaldo5740 Жыл бұрын
Can’t you drill out the side and tap it. Then just put in a bolt with a washer?
@hotwheelsracer6380 Жыл бұрын
I wouldn't risk it.
@riannesmith8669 Жыл бұрын
I can't get the 2nd screw off. My drill won't even remove it. Tried some wd40. Now it's kinda stripped, any recs for how to loosen this? Seems like it's freaking welded on or something.
@hotwheelsracer6380 Жыл бұрын
No idea
@hotwheelsracer6380 Жыл бұрын
Best answer i got for ya is to drill it out and re tap it
@slingbart705 Жыл бұрын
Vice Grips to break it loose, my impact wouldn't do it either, and i didn't want to break my bit or strip it.
@sf4938 Жыл бұрын
I don’t know what to do after I greased it and tightened the gearbox and the guard the gearbox kept spinning how do I fix that
@hotwheelsracer6380 Жыл бұрын
Its gotta be pretty tight
@Moncho68 Жыл бұрын
Hi, what kind of grease do you used ? Thanks
@hotwheelsracer6380 Жыл бұрын
I used lucus red-n-tacky. Thanks for watching
@Moncho68 Жыл бұрын
@@hotwheelsracer6380 Thanks a lot...greetings from SPAIN
@webberalex9533 Жыл бұрын
For a fs 460 c i grease it like in this video?
@hotwheelsracer63806 ай бұрын
Im not too sure
@LeonMTan Жыл бұрын
maybe Stihl think some model are too "domestic" and wont be used too much.
@harryerhart5978 Жыл бұрын
Fc91 edger also has no grease port👍
@hotwheelsracer6380 Жыл бұрын
This method may not work.
@ralphnannola5889 Жыл бұрын
Good info terrible filming.
@hotwheelsracer6380 Жыл бұрын
Thanks for the support man this is how KZfaq should be. You left a good comment while also stating what I could have done better. I'm not used to making videos of this type so I do need practice. Thanks!
@hmooney8552 Жыл бұрын
Nah it's informational not looking to win awards lol
@rockylincoln8418 Жыл бұрын
Great video mate, well done, solved a problem l'd been stumped on. Cheers, owe you a beer 🍺