Thanks 👍😍

And the oil pollutes the groundwater.. No occupational safety measures. And we talk about environmental protection.

🎉🎉👍👍🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉👍🎉🎉🎉🎉🎉🎉🎉👍👍🎉👍🎉🎉🎉👍👍🎉🎉👍👍🎉👍🎉🎉👍🎉👍🎉🎉🎉👍🎉🎉🎉👍🎉🎉🎉👍🎉🎉🎉👍🎉🎉👍🎉👍🎉🎉👍👍👍👍🎉🎉🎉

The cleaning solvent put on old liners, the solvent getting on the practically dry crankshaft with new bearings, didn't torque the mains or rods, & that's a good job? Remind me to never take my trucks to your shop!

@@vaterlandgr7553 and I ain't gun no gum

Thanks 👍😊

You forgot the biggest one...NO STARTUP EITHER!

Heck yeah, I could live without the air tools but I would be snapping bolts without the torque wrench!

the manuals are a good place to get torque and many other engine specifications to ensure that the engine will run properly. parts need to be more than cleaned, they need to be measured and inspected. This get get them by for another year or two and they will have a repeat customer. Not putting these guys down. They do the absolute best with what they have

that profit would be 10,500 Rupee in Pakistan, Which is less but can't complain about that I guess something is better than nothing..

How much would they be able to make as a profit working in America on the same kind of engines?

@@sameedakram3939 They would start out at around $60k per year U.S. dollar's. Plus full benefits like medical care, paid vacation time every year. You get paid for Holidays that you don't have to work. Overtime can put you at about $40 dollar's an hour or more when worked over 40 hours in a 7 day week. Plus a 401k retirement fund. The metal fabricating they do at the right jobs in the U.S. they could be paid 6 to 7 figures per year. That's $1 million or more U.S. dollar's.

Thanks

I believe most head gaskets are to be installed as is with no sealants and allowed to bake in.

Thanks dear

Thanks 👍😍

Never seen anyone use gasket sealer on a head gasket either. Maybe Hino is different though, never worked on one.

What si wrong with Craftsman tools. The original Craftsman before it got acquired by Stanley Black & Decker is still the number 6 best brand in the world. lol

Vai sobrar um monte de parafuso,eu aposto. Aqui tava todo mundo preso trabalho infantil, comunista não deixa ninguém trabalhar.

Thanks 😊

Thanks

Thanks 👍

Thanks 👍

Thanks 😊

An engine will work if parts are not within a certain tolerance. They may not perform as well or last as long but for the most part they will work as long as the tolerances are not ridiculously off.

No utizan torquimetro 😮😮😮

@@leisonraulparraortiz5235 tenés razón no usaron el torquimetro !!!!!!

@@joserodolfoaguirre4937 son muy chanbones

@@leisonraulparraortiz5235 si Raúl pero cómo anda si no usan el torquimetro se sopla la Junta enseguida se desarma el árbol de levas ??????

@@joserodolfoaguirre4937 bien amigo no esos locos tienen una suerte Barbara . No miden nada Armán eso sin ningún ajuste no calibraron válvulas

Thanks 👍😍

@@paktech9707 yes sir.. In indonesia, hino is favorit truck n no 1.. Assallamu,alaikum..

Walikumsalam

Thanks 👍

Thanks

That might be a minor problem.. 😆 Reuse cylinder head bolts.. and wash the fuel filter in dirty Diesel.. and don't change the oil pump and water pump. The list is long 😆😆

Thanks

Thanks 👍

I agree I never ever see a torque wrench. I guess they have one in there arm. Or everything gets as tight as you can. The bigger bolts get a 4foot cheater pipe. They Don't mic. Anything either. This is more of cleaning it up with new bearings and rings. I guess they replaced the sleeves on this one. But didn't use any sealer on the bottom of the sleeves. I would not call this a complete going to get 200k miles out of it. This is more of a freshen up and put some lipstick on it and call it a major overhaul. In my opinion. But they may have not shown everything to. Still impressive my mechanics that work for me would bitch the whole time if they had to work like this. For sure.

Thanks 👍

@@paktech9707 已看。

Most importantly, I believe they reused the same liners! Im only guessing they put in new rings, not sure. That and piston rings are so crucial. Waste of time otherwise. We never knew what the original diagnosis was either.

Not sure if that flywheel was machine surfaced, or somebody went at it with a hand power tool sander??

Lol

i think they were the old pistons and liners. It was hard to see, but whhy would they be cleaning brand new pistons in gasolin?

Thanks

Thanks 👍

its not an engine rebuild, its a freshen up

туалет в армії прийшлось мити щьоткою зубною, тоже було діло в учєбці

@@user-qc1ou6lj9g служил на Сахалине с ребятами с Винницкой области 1976-1979 годы, сало им присылали очень вкусное.

And it runs 30 times longer.. 😎👍