My HMMWV is stuck in the safety mode (2nd gear). Did you have to disconnect the glow plug controller box as it states on page 60 of the manual? Thank you!
@mtvrchannel30513 жыл бұрын
@@btrev5183 I did not have to disconnect mine for diagnostic purposes
@btrev51833 жыл бұрын
@@mtvrchannel3051 Thank you sir. I ended up getting it to work. I followed chart A1 and was able to get it to shift. Thank you sir. Keep up the good videos!
@kingpin761103 жыл бұрын
@@btrev5183 Mine is doing what yours is. Did you get it fixed? If so how did you do that. I’ve been fiddling whit mine so long I’m about to sell. This thing is just a pain in the butt.
@renevivo3809 Жыл бұрын
Thanks for the video. I just picked up my 1993 AM General 998 with. 6.2 and a 4 speed. The engines is in truck suspension engine overall great shape
@davidhorbenko71439 ай бұрын
Great video. I have learned alot
@Hafellafuse11 ай бұрын
Amazing video!! Thank you for this guidance!!
@brianlacroix68946 ай бұрын
great video thanks.
@SecurityisaMyth6 ай бұрын
Well Done!
@sayedyasine30402 жыл бұрын
Thanks
@marcelwengerter844210 ай бұрын
Thanks for the video....anyone have any idea as to what would cause the TCM not to respond when jumping a&e? Trans light just stays lit
@hofmanjim9 ай бұрын
I have a Humvee that may have a similar issue. I have the M1152 6.5 L Diesel. The brake switch is the same as what you have. The vehicle will go into over rev and struggle to maintain 40MPH. The engine is fine.
@AndieWanKenobi2 жыл бұрын
I’m having a 38 code, and tested the switch as you did with my multi meter, but I’m not sure what it should read to be a good switch. My transmission is stuck in limp mode (1st). What should the resistance be?
@benjilacombe74787 ай бұрын
I just bought a 4 speed truck from auction. Missing the front right axle. The truck will move if transfercase is in HL and L but will not move in H. If I tap the brake while case is in H and trans in Overdrive it tries to engage but doesn't. All the fluids are good. I'm new to this, your experience would be greatly appreciated.
@StevenPenny2 жыл бұрын
Great video. Any chance you’d have a guess on late shifts and redlining at 62mph? I’m at 33-3400 at 62 so it’s like it’s not going into overdrive.
@jacobkasson9580 Жыл бұрын
Are you locking and unlocking the tourqe converter by applying the breaks?
@remy6978Ай бұрын
great vid. Is this truck a serial under 29k or above? or does it not matter when using the jump cable on the tcm to find your codes,
@Cucuy-so9dnАй бұрын
Will this break switch make the transmission not shift out of 1st gear ?
@deeznutzz83753 жыл бұрын
Great video. You should have a video and a way to send you $ for your knowledge!! Put that link in the description.
@mtvrchannel30512 жыл бұрын
Thanks!
@skilltouchinc9 ай бұрын
My Hmmwv is not shifting in overdrive . do you have any suggestions ?
@SashaNem3 жыл бұрын
Hi, did you have an experience with new Oshkosh S-ATV ? is it match better and more reliable than Humvee ?
@mtvrchannel30513 жыл бұрын
Unfortunately I don’t have any real world experience with them
@kalebnolen16163 жыл бұрын
Nice Genny you got, before long you'll have your own Motor Pool 😂
@mtvrchannel30513 жыл бұрын
I already feel overwhelmed 🤣
@mtvrchannel30513 жыл бұрын
Thanks!
@ibidapobisi90082 жыл бұрын
hi pls, great video. can u pls recommend the diagnostic OBD that can be used?
@mtvrchannel3051 Жыл бұрын
You don’t need one
@jacobkasson9580 Жыл бұрын
How do you lock and unlock the torque converter? Is when you step on the brake?
@mtvrchannel30518 ай бұрын
I had a manual toggle for demonstration purposes in this but yes the brakes do it
@raymondfuschino3733 Жыл бұрын
Sir, I have just aquired a 1988 AM General M1097A2. I followed your video and it gave me code 73. The issue im having with it is that it will not go in reverse. If there is any advice you can give me I'd be very grateful. I can not find what 73 is.
@mtvrchannel3051 Жыл бұрын
Check my “pinned comment” at the top of these comments, open the link in it, and go to code 73, you probably don’t have 4th gear either. The manual you’ll see will have an entire guide for diagnostics
@hofmanjim8 ай бұрын
What was the reading on the ohm meter? I heard the buzzer but can’t see the reading. Mine read .3 and then pressed down OL out of limits.
@mtvrchannel30518 ай бұрын
That’s what it should be. You’re looking for
@hofmanjim8 ай бұрын
@@mtvrchannel3051 Thank you I am lucky to hold .3 ohm when moving/brake not applied.
@wakesurfingfool Жыл бұрын
My M1097A2 4 speed is in limp mode and stuck in second gear. Will shift into neutral and reverse, but goes and stays in 2nd once I put it to drive or overdrive. Help me brother!...lol
@mtvrchannel3051 Жыл бұрын
It all starts with my comment pinned at the top of comments, go in that guide and pull your codes. There’s a step by step all inclusive guide inside that manual
@FREEDOM9911 Жыл бұрын
My torque converter locks in and out while driving between 50-65 mph over and over. It’s a 2008 m1123 4 speed. Any idea? I can send a video to a email if needed
@mtvrchannel3051 Жыл бұрын
Have you pulled the codes yet?
@FREEDOM9911 Жыл бұрын
Not yet. I unplugged the two prong connector while driving locking the torque converter in place and the problem stopped. You stated there is a process to adjust the brake module sensor if it’s out of alignment. Do you have a link on how to do that?
@hilalmelhem41313 жыл бұрын
connecting jumper cable pin A and E of the J2 TCM connector. trany flash light : *_*_*____*_*_*____*_*_*____********(8)_*___********(8)_*___********(8)_* . what does mean ?
@mtvrchannel3051 Жыл бұрын
There’s a manual link in here
@JHashfather3 ай бұрын
I’m getting the same code. 8 lights. Did you figure out what it means? Thanks.
@renevivo3809 Жыл бұрын
Sorry, fat fingers,….. but the tranny won’t shift out of first gear. What should I do? Does the fact that I have no break lights working mean ghat The dual break lights switch in your video is the culprit?
@mtvrchannel3051 Жыл бұрын
Chances are, it’s stuck in 2nd gear limp mode. Pull your codes and see what you get