Holset HE351VE VGT Turbo Common Failure, Disassembly, Initial Cleaning & Inspection

Рет қаралды 7,972

Жыл бұрын

This is a Holset HE351VE Turbocharger off of a 4th generation Ram truck. This is an amazing turbo but it’s not perfect. We talk about the common failures and initial inspection so we can order the correct parts to make this turbo charger better then OEM factory new.
How it should have come from the manufacturer in the beginning.
Amazon Links:
Rebuild kit
amzn.to/451q02J
VGT Nozzel & ring
amzn.to/45I4PDR
#holset
#turbodiesel
#cumminspower
#cumminsnation
#ramcummins
#mechaniclife
#mechanic
#turbo
#turbocharger
#cumminsisx
#vgtturbo
#turborebuild

Пікірлер: 25

@scbane 9 ай бұрын

Just FYI, there are many horror stories about Amazon turbo rebuild kits, mostly because of unbalanced vanes/compressor/shaft.

@DIYKAI 9 ай бұрын

We reused the OEM shaft 15K hard miles still running strong

@DIYKAI 9 ай бұрын

Fortunately we had a good set of bearings to measure and the turbo labs one from Amazon is spot on they even include oversized in case you need them most don't though

@koreygullett6485 3 ай бұрын

How do you take the shaft out of

@DIYKAI 3 ай бұрын

Should come out with a slight tap rubber mallet or wood only

@jshlds46 Ай бұрын

Where did you get your exhaust downspout or what is the brand name?

@DIYKAI Ай бұрын

@@jshlds46 are you talking about the down pipe that comes off the turbo?

@jshlds46 Ай бұрын

@@DIYKAI yes

@DIYKAI Ай бұрын

@@jshlds46 its the stock one because this is the stock turbo 4in

@maritimeus 8 ай бұрын

Those CTT VGTs get stuck a lot less compared to the articulated foil/vane design of the other big turbo manufacturers. Aside from carbon and oil buildup, I’ve never heard of an OEM Cummins VGT nozzle ring failing in like the last dozen years. Their wear resistance is really what makes them stand out compared to the articulated designs. They even handle FOD really well. Must be some damn good nitriding I’d imagine. Have you seen much chipping or deforming of the nozzle ring vanes? Occasionally I see some, but never had it seize. What do you think? Great video man.

@DIYKAI 8 ай бұрын

So if we were to do it all over again probably would have left the stock nozzle ring on the hot side and just changed the nozzle only. After 250k they looked pretty good in this turbo we just wanted to see if it was going to make a difference (very little if any) but the actuator is a issue in the 4th gens and some 5th we have been through 2 so far and about to try one now before we ditch this turbo for a new one

@maritimeus 8 ай бұрын

@@DIYKAI thanks so much for the response! Have a great day.

@DIYKAI 8 ай бұрын

@@maritimeus your welcome! You as well!

@BIG-AL-GARAGE 11 ай бұрын

Where did you order the rebuild kit from?

@DIYKAI 11 ай бұрын

Amazon, we updated the description with links.

@BIG-AL-GARAGE 11 ай бұрын

@@DIYKAI OK I see it now thanks man I appreciate it

@DIYKAI 11 ай бұрын

@@BIG-AL-GARAGE no worries good luck we have 10K on the rebuild so far

@BIG-AL-GARAGE 11 ай бұрын

@@DIYKAIawesome!! I have a 2018 ram 3500… would this be the same process?? I have dug into it yet so I’m not sure which turbo I have but I’m having a lost communication with the turbo code… I have to take the actuator off and check the shaft

@DIYKAI 11 ай бұрын

@@BIG-AL-GARAGE yes i believe from 07 up was the HE351VE look at the sticker on the side of the actuator it should say......definitely check the actuator arm you should be able to move it with one finger and hear a metalic clunk at the stops any resistance and its probably carbon filled.......check shaft play also on the turbine a little side to side is ok ZERO in and out