Thank you again for another fine instructional. I've been learning a great deal from you and began casting for the first time this past spring with great success right off the bat. No leading on any of my pistols.

Just an FYI. Wax rings w/o the plastic flange are also available and cost even less ; )

My man I would like to thank you for your videos! Recently have been getting into reloading and you have helped me along my journey so much I appreciate it!

I’ve lubed a lot of bullets hand style with those toilet rings. Just straight smeared it in the grooves. It works . Amazing how little u actually need

Awesome idea. Thanks for posting great reloading info!

Sir you did such a good job as usual. Welcome to reloading family.

Seasons Greetings Cookie, thanks for all you do for our hobby, from Canada, Mike

Great video! Thank you. Merry Christmas to you and yours!

Round metal cake pans from the Dollar Store work great for pan lubing. Cheap and last a long time.

Interesting as usual. Now I am waiting to see the results at the range and how well they prevent leading as well as accuracy. Thanks for the video.

I started pan lubing a long time ago. I reload for a Sharps and High wall, 45/70 and 45/90. I came across a good supply of Alox and the bees supply the wax. I use a 50/50 mixture. I shoot as cast, no resizing. After a lot of experimenting with the time factor I have found that after the lube is firm enough to pick the tray up, I put the tray in the freezer for 12 minutes. Any longer and the lube is too firm to press the bullets out and get full grooves. Any sooner and the lube is still too soft and will smear out of the grooves. When it is just right a push with the thumb and they come out clean and lubed and ready to load. So from the time I pour the lube until I am loading bullets is usually around 20 minutes. With a different lube mixture you will have to play with the time to get it just right. I got rid of the Lube Sizer.

Good video ! I custom make cutters to slide over my projectiles and cut wax...I had not seen this method.

Couple of tidbits I might could add, not sure about msmokeless powder but I do know that paraffin forms a type of asphalt in your barrel when used with blackpowder. Also, you can pick up a fairly cheap boy scout type camping mess kit with one of the 1 qt saucepans with a top to melt your lube in and it not only comes with a handle, it comes with a top that can be snapped over it for storage and some even have a little pour spout making pan lubing a bit less messy.

Outstanding video good sir! Thank you for sharing this technique

Man this is just the coolest idea what a great job it does!!!

Happy Christmas!

Sure beats the heck out of paying 6 to 8 bucks a tube for actual bullet lube. Thanks for a great money saving tip. :-)

Another great video! Thanks Professor👍🏻

I had a tubular cutter that cut the bullets free from the cake and the bullets would come out the other end. You could get 3 or 4 cut and then the 4th or 5th would come out the top and you could put them in another tray or box. I had only cast for 38spl/357mag, it was fun. With the state of television and other electronic media, outside a few great KZfaq channels, being virtually useless and disgusting, I might need to break all my old reloading equipment out to a make better use of my time. My lead melting pot might not work after 35 years, but I should try to find out. Thanks for the inspiration.

The powder coat looks like dull copper or bronze, I love it.

Metal coffee cans are a rare commodity these days....and soon to be heirlooms!

This idea about the Home Depot beeswax is gold!

Big Thanks!

Great, there has been a run on wax rings at my local Home Depot... ;) Just kidding. I have a ton of parafin from a reject batch of Histology embedding medium and now I know how to make use of it. (new in packaging, not used.) Thank you for all the good info.

Awesome video ! Reminds me of those old Remington .22 clean bore ammo, I’m sure these are way better though lol

Thanks for the video.

Thanks for making this video

Up to the early 70's Lyman had something called a 'cake cutter' that was a tube slightly sharpened & the size of the bullet. You melted the lube in a metal pan with the bullets standing in it, once cooled you pushed the cake cutter down over the bullets cutting away the lube & the bullet pushing up in the cake cutter. Leaving the lube in the pan, set more bullets in the holes, melt & add just a little bit of lube. The bullets could be used or sized with a 310 tool. Lee made a similar luber in the 70's. 2:00 am 12-25-20, Merry Christmas

It's criminal that you don't have way more subscribers.

great stuff, and subscribed!

I find the easiest ,and less messy way to remove the bullets from the lube is to take a fired case, drill a hole through the primer pocket, insert a 3/16" large head screw,(because it has a round head), with the head on the inside of the case, then when you push the case over the submerged bullet it shears the bullet out neatly, you then hold the case over a container and push down on the screw which ejects the perfect bullet into the box, easy and no mess as you have not touched the lubed bullet with your hands.

Had a good laugh recently over here in Germany, a fellow reloader asked where to get wax rings in local home improvement stores. Alas, german toilets use rubber or urethane rings 🤣

Hey FC! please publish the recipe for this lube. the ratio for wax ring to parafin is important

Merry Christmas

Wow thank you .i just keep learning 😄how to make my 44 mag cast bullets .and lee 1 /0z slugs ....its fun too...

Soooo nice!

I use surf board wax and mix it with Lee alox bullet lube. I stand them up the same but I use a flexible neoprene cake tray and just peel it off when they cool.

I uses 454 Casul cartridge for cuting wax from 45 ACP lube cavities.

Miss my Lubesizer! I was just going to alox but this is awesome I totally forgot about pan lubing. Sucks KZfaq is for kids now! Fortune Cookie 🥠 and many others would have really blown up if we were allowed to show the full reloading process, etc! The good old days man

Make a double boiler out of two different size cans. The larger can will have water in it to allow even heat on the inner can that is holding the wax. You will not have to continue stirring and makes the job much easier.

I have a sizer/luber, with a heater for the lube. It's seems to do a good job

very informative and thought provoking as always -thank you what kind of mold did that .45 heavy wadcutter bullet come from ???? headed to home depot !!

Happy New Year Mr FC! For my clarity, is it necessary to lube powder coated (p/c) bullets or was this a training video and all your bullets happened to be p/c? To be sure sir you are a GENIUS! You put the "M" on MacGyver. I wish I could know you in person. You are quite knowledgeable in everything.

Try adding some Liquid Alox and some transmission fluid to your mix. You'll have to figure out the ratio, but I think you'll love the results in your firearm's barrel. :)

a question or 2, would the powder coat actually keep the bulet from expanding as much to fill the grooves, and do you lube the powder coated bullets a little as well.

You can also mix in old crayons. I save all wax to mix in for my lube. The toilet rings themselves are just to soft these days. Sometimes it takes a little playing around letting your mix cool down then check if it is as firm as you want but goes a long ways once you make up a good batch.

The old way before paraffin wax was bees wax. If you are around places or know someone with bees it will work. I have a 1873 Winchester rifle that is a 44-40 and have spent a long time looking up how they loaded this ammo then. I have found that bees wax was the lube used.

How do you like the 45-70 bullets from your mould? I think I just bought the same hollow base bullet mould at a gun show on the weekend and am wondering how you find them accuracy wise?

i did lube bullets in a electric themp controled frying pan ,just dump the bullets , in the basket in the molten wax , a, carnuba ,parafine ,and beewax mix. and shake them af and dump them on wax paper. you get a film over the whole bullet like a 22lr

I wouldn't be surprised if the ATF raids home Depot

I usually like your videos, but this one deserves a like just for “waccidents”

Do you use a sizing die for 12ga slugs? Where can I get one?

On a casting subject: you seem to be against smoking molds as Lee suggests. Why? Are they any negatives to smoking a mold? Thanks, and Merry X-mas!

Nice...

Hello fortune cookie 45 Question; I have 38sp 158 gr powder coated comes up 160_gr. I use w231 can’yt find powder charge for same should I use 158 gr. powder charge data?

I just wondering if you can tell me if 38 cold automatic would use the same brass as a super automatic so I can I can find a 38 Colt to reload for it

No STP oil treatment? Steve, It looks like you found a lesser expensive pan lubing recipe.Good stuff!

Is that powder coat a mix of different colors and brands?

Merry Christmas FortuneCookie45LC maaate!

I could not find where youemtion the exact/approximate ratio of ring wax to candle wax. Could you elaborate?

Does it smoke as much as 45/45/10 tumble lube does?

Fortune cookie, what copper powdercoat did you use at 13:55?

Does this lube method surpass the powder coated method?

going to need the ratio of wax ring to paraffin or candle wax - just in case I ever run out of powder coating

Good thing i have a old pan lubing kit 🙂

I’m looking for a exact recipe amount for rifle velocity like over 2,000 FPS and will it need a heater thank you

Is this lube useable for smokeless powder?

I could see using this for cast lead and powder coated .300 Blackout bullets. The powder coat is enough, but a gas check and or pan lubing after powder coating would be even better.

So does the waxing help with full copper jacket loads or do you need the lead cast loads?. This isnt the same as gas checks is it?

Hey FortuneCookie45LC, Does powder coating take the place of lube or is it beneficial to do both? I shoot a lot of 45-70 in my trapdoor & sharps rifles & I cast my own lead bullets along with using either Goex or Olde Eynsford Black powder. I guess the question is, if I powder coat my cast bullets, can I choose Not to apply lube to my bullets?

Very nice presentation. I would have bent the top of the can for a pour spout and wore ruber gloves to push em out. But a wooden dowel would work too. No matter what your system works. Would like a side by side at the range smoke test with the more conventional factory bullet lubes. As some of those factory lubes claim they are lower smoke over others. And I'm not sure how accurate that would be as I've seen a lot of smoke from modern powders on many videos when using factory loaded FMJ's in some fast shooting demos and slow fire too.

Did you copper plate the 45 wad cutters if you did that would make a good video.

Are toilet was rings natural or a they a petroleum based wax? Asked for use (or not use) for blackpowder.

FortuneCookie what happen to all of your bullet casting videos? Have you or will you put them up on Rumble?

Great Video FortuneCookie45LC ! Merry Christmas from Canada !

to change the subject just started pc to lub the bullet why can't we use other soft metal like aluminum i am just a getting into pc and i thought i would someone that would know thanks

never noticed before with those wax rings but it sure looks like beeswax

When I first started loading and casting, I used the Lee pan lubing kit. I wish I'd thought of simply pushing the bullets out of the cake instead of using the kit's cutter. I intentionally made my lube harder than commercial sticks, and had to put the cutter on a box with a recess in the lid, and push the bullets out with a dowel. It was almost as difficult to remove them from the cutter as it was to pound them through the first generation unthreaded "push through" sizer with the included punch. That sizer was a trip as well; I had to twist the punch and sizer apart with opposing vise-grips after each bullet. That said, I was a young broke LEO trying to keep myself in training ammo, and loaded many thousands of rounds in that fashion, on a single station press. What I would have given for a lubrisizer and a progressive press back then ('70s)!!!!

Why lube powder coated bullets?

Dollar Tree has lots of candles I've bought blocks of paraffin at walmart

Are we brothers? I’m not Asian but I think we’re brothers. Great job man!

I love your videos I especially like the fact that you look into products and processes rather than just accepting them I have been loading buckshot loads of all types and really enjoying myself but so many loads now require Buffer I have seen no difference in accuracy with or without but my main issue is what is buffer is it flour is it baking soda is it ? It is very expensive if I am paying for something I like to know what I am paying for do you have any idea or comments on the subject by the way love the subject on bullet lube amazing thank you fortune cookie for your ear

Can you tumble lube with liquid ALOX all bullets or just lee tumble lube style bullets?

How do you know how much paraffin to add to one of the rings ?

Do you get anything from the commercials at the beginning of your video? If not I'm going to skip them .

I used to pan lube until I discovered powder coating and (Harbor Freight red). Dollar store religious candle s are a good source of wax too.

what's that .45 wad cutter ??? is it Matts ?

I thought you were doing the hot lead zone take on peanut brittle, bullet brittle.

Your pretty sharp for a old guy. lol

Is pure beeswax too hard?

If I were to do pan-lubing, I would first push my cast bullets through a sizing die of appropriate diameter. And since the sizing die allows lubricant to be squeezed into the grease grooves of the bullet, why bother pan-lubing?

I just lubed my .44paper cartridges with wax I bought at Home Depot (toilet Bowl seal.I"let you know how they shoot.

WhT is the ratio of wax ring and paraffin?

I just tried this method on 405 gr .45/70 and 170 gr .30 bullets cast from Lee molds. The result was dismal. Not one usable bullet from the entire lot.

I made all the bullet Lube I could ever use years ago. I thought the powder coating was supposed to end all these problems, is there issueswith powder coating, and leading of the barrel? I haven’t seen it with all the powder coated bullets that I am shooting. Pretty soon will be powder coating lubing and using gas checks.

Why when there is powder coating?

Casting bullets is fine ,but you can't get powder or primers ,I guess I'll make a slingshot I live in the country of california !

No Waxidents? Lol😂

I do woodturning and I melt my wax in the microwave

A safer method, I am sure you are aware of is put the can in a pan or pot of water and boil it.