Honda Accord Rear Wheel Bearing Replacement (2013-2017)

No video

Honda Accord Rear Wheel Bearing Replacement (2013-2017)

Рет қаралды 49,252

Күн бұрын

2013-2017 Honda Accord Wheel Bearing replacement
--------------------------------------------------------------------
TWITCH : / manizilla
SNAP-CHAT : / manizilla
INSTAGRAM : / manizillatoolbox
--------------------------------------------------------------------
Disclaimer :
Creator 'ManiZilla' is a trained professional in his craft and works with his own safety in mind; as should any viewer.
--------------------------------------------------------------------
Don't Mind me just dropping some tags
↓
#Auto #Cars #ZillaSquad

Пікірлер: 51

@bdubbin16 Жыл бұрын

Thanks this was useful! A few tips for others: 1) the brake guard can be undone so you can rotate it around the wheel bearing assembly and then be able to hit the wheel bearing from multiple sides instead of just one as shown in the video. 2) with a 10mm socket you can take out the ABS sensor from the top so you don't have to worry about damaging it. 3) I didn't need a flexible wratchet ... a solid one did the job.

@swaggerjacker1482 Жыл бұрын

What makes a wheel bearing go bad?

@G3RRYxC 9 ай бұрын

@@swaggerjacker1482I think just wear over time/use. (Probably wears faster in wet climates?)

@swaggerjacker1482 9 ай бұрын

@@G3RRYxCmakes sense

@joet4806 5 ай бұрын

Excellent Leadership & Teaching Skills! Direct and to the point. Thank you

@scottl072 10 ай бұрын

Thanks for keeping your video so clear and to-the-point.

@bobbymathis1700 3 ай бұрын

Excellent tutorial and video editing! Well done and thank you.

@DAlilbigman 2 жыл бұрын

Nice video Manny! Thanks for sharing. Wifey is hearing a humming noise from the rear passenger side of our 2015 Accord. It only hums at 50 mph. Had the new tires checked and all was good. No holes in the muffler s my guess it’s the wheel bearings.

@jasonoid-official Жыл бұрын

Got the same problem on my 2014 rear driver bearing.... I caught it before it got this bad though. Thanks for the video.

@johnregal5098 Жыл бұрын

Fantastic vid. Thank you so much for doing this.

@4Runner21 6 ай бұрын

Any torque specs? Or is good and tight good enough? Is this same or similar for 13 Acura RDX? Thank you!

@goofyGAguy Ай бұрын

72 foot-lbs.

@bobbysmith9803 Жыл бұрын

Well done video and very clear looks like 12k quality

@RavRam15 2 жыл бұрын

Good job Manny! 👊🏾👌🏾👍🏾

@ManiiZilla 2 жыл бұрын

🙏🏽 thank you

@davidhollfelder9940 Жыл бұрын

Parking brake cable won’t let you pull the caliper. You left that part out.

@kenjones2874 2 жыл бұрын

Great video!! Nice music too.

@falecf4 Ай бұрын

"Nice and tight" being 80 ft-lbs for the hub bolts and lug nuts.

@raminderparwaga 2 жыл бұрын

Sick video!

@ManiiZilla 2 жыл бұрын

Respect brother 🙏🏽

@tonyfeldscher2209 2 жыл бұрын

Will the wheel bearing not make noise when going in reverse? My accord makes the noise when going forward only. Happened after I replaced stuck rear caliper.

@zaneyone1 2 жыл бұрын

Tapping the bearing assembly out evenly will make it come out easier than beating it out on one side as you did. Otherwise, good video.

@techieguy336 2 жыл бұрын

There's only a small section which can be accessed with a hammer. How would you tap it evenly?

@shamzpachino4778 11 ай бұрын

I followed this video and the only thing I did different was remove the “brake shield” so I can bang from more sides. It was the little 10mm screws.

@cyreese3720 2 жыл бұрын

Do you know if it's the same process for a 2018?

@ShiftyReaperGaming 2 жыл бұрын

Most likely been like this for years fronts are pressed in rear is bolted in like this one nothings ever changed due to it being Front wheel drive if it’s all wheel drives will be different

@dannysautorepair 2 жыл бұрын

Great video thanks

@chstewart3715 19 күн бұрын

I'm not doubting the HUB was bad, but loosening the tire then shaking it was kind of redundant

@1Challino Жыл бұрын

Thanks!!!

@Awake2Evil 4 ай бұрын

What are the sizes of the socket you need

@cool124 3 ай бұрын

Hi, How long does this generally take?

@detect2protect 4 ай бұрын

what do you use for the spray penetrating oil?

@jjspatel 9 ай бұрын

What is the cost of one wheel bearing of this model?

@nevelis 5 ай бұрын

Probably about $50

@Ez-sk8ig 3 ай бұрын

Buy quality parts and do the job one time. Skf, Timken, ACDelco, even Moog is better than the cheap ones or no name. I always check the warranty time to see. Timken will usually be lifetime, but they are also the most expensive.

@devonteparks614 2 жыл бұрын

Hey what is that thing your using to tap it im stick currently trying get mines off?

@ManiiZilla 2 жыл бұрын

I use a punch with a hammer If yours is really badly seized you may need to use a torch to heat it up and then try to hit it

@joela6895 2 жыл бұрын

get a slide hammer. theres youtube vids on it. i spent 2 days trying to get mine off with a hammer and flat screw driver. i used the slide hammer and it took me 2 mins. fuuuuuucccckk

@BeenLogic 2 жыл бұрын

For the 2016 model sport do I have to worry about a abs sensor for the same drivers rear wheel ??

@inibrasiumthefirst2680 2 жыл бұрын

probably. abs sensors arnt bad just carefully remove them. also some times they get stuck and they break so its always better to be prepared to replace it