Thanks so much - my cv just blew out this video helps
@devinwilliams90582 ай бұрын
Super helpful thanks man.
@haroldscott851610 ай бұрын
Great video. Thank you for posting.
@theeverythingchannel9145 ай бұрын
Great video man thanks brotha!! Smooth as f boy🤙🤟🎯
@pradeeptrehan794811 ай бұрын
Thank You, Very detailed Video
@tiredhowudoin8 ай бұрын
Great video! Just had my 2014 Honda Accord 2.4L axles replaced by dealer on recall. I love to watch the videos on the repair as a DIY'er. Will be doing my front brakes this weekend.
@jimihiggins55806 ай бұрын
Was the recall just for 2014?
@taingTv6 ай бұрын
But not all the accord 2.4 affected depending on the vin #
@gregjmitchАй бұрын
Thank you!
@jcfpv345411 ай бұрын
Thank you
@philipjohn13387 ай бұрын
Thanks for the video. I will be attempting this in my driveway
@taingTv7 ай бұрын
Yea but its difficult to work on the floor specially when u trying to hit the knuckle to loosing the ball joints u will found out when ur doing it
@Rockstarsf6 ай бұрын
@@taingTvwhat if we rented a ball joint removal tool? Autozone has them
@dicegamenetwork2 ай бұрын
Whats the torque spec on the axel nut when you put everything back?
@bronniesboy7 ай бұрын
Did you have to top up the gearbox fluid? And would spraying wd40 on the axle joint to intermediate shaft side help with the detachment. Might not have as much space as you to work under car. Is it just because the splines have a little rust on them or is something else making it stubborn to remove
@taingTv7 ай бұрын
The transmission fluid yes top it off when u remove the driver side axle the fluid will come out u must top it off yes
@Abuhummus8 ай бұрын
Hey thanks for the video. Is this the same procedure for a stick shift 9th gen accord?
@taingTv8 ай бұрын
Yes similar just when u try to remove balljoints thats the most difficult part
@ldan-nd3ds6 ай бұрын
I replaced both knuckles. It is easy on the lift but able to hit it hard enough 100 times to separate the ball joint. What happens to torque wrench? Turn the shaft is the trick to get the axle clip to the right position for it to snap out.
@taingTv6 ай бұрын
Just need to hit the right angle but if the ball joints have play its hard to get that ball joints loose only if u have a helper that pry and put pressure on the knuckles then would be easier for you i dont think they have torque those just either gun that nuts on or hand tight
@JoseSMercado6 ай бұрын
Will it be the same procedure for a V6? Thanks!
@taingTv6 ай бұрын
Yea its should be the same
@MrUGA20107 ай бұрын
do you have to do the alignment afterwards?
@taingTv7 ай бұрын
Yea u suppose too
@casperstevvo420 Жыл бұрын
Did u have to refill transmission fluid?
@taingTv Жыл бұрын
Yea just a little bit not much
@mp-xs2cd6 ай бұрын
How can you tell when the axles need replacing?
@taingTv6 ай бұрын
If the axle boots torn or u can see the corrotions or crack in the middle of the rubbers but after market axles they dont have the rubber race in the middle of the axle , if u feel a vibration when u accelerating on higher speed , or they make noise when turning , sharp turn either left or right or even in reverse
@tricao57 Жыл бұрын
Xe của em phát ra tiếng kêu lụp cụp bụp bụp bụp trong lúc tăng tốc, tiếp theo là em để Transmission in Park, engine on idling, xong rồi lấy flash light rọi vào trans fluid filling hole thì thấy fluid nó bị Foaming sủi bọt, Có phải là U joint của front axle bị hư ? Hay là Transmission có vấn đề ??? 2014 accord sport 2.4L automatic transmission, 114k miles
@taingTv Жыл бұрын
Ma cho bao bi sui bot? Ko fai axle dau ma cai noise do nhu the nao ?
@tricao57 Жыл бұрын
@@taingTv Nếu dừng xe thì không có kêu, khi nào tăng tốc từ zero đến 35mph or 40mph thì xe phát ra tiếng kêu: “ knocking, clunking…hoặc là có passenger fart in the car, tiếng kêu lụp bụp
@taingTv Жыл бұрын
@@tricao57 co the cai wheel bearing do ko fai cai transmission dau hoac cai tires cua e bi chopped
@tricao57 Жыл бұрын
@@taingTv thank you, em sẽ mang ra dealer của honda để service.
@gvilla9253 ай бұрын
I can't get my lower ball join back in lol
@taingTv3 ай бұрын
Yea kinda tough to do put it back on just need another help u pull it down meanwhile tey to guide that ball joint back in
@ELBrazoArmado Жыл бұрын
You said a recall on the axles?
@taingTv Жыл бұрын
Yes but if ur vin# fall it under the recall not all on them will cover
@meeemann1187 Жыл бұрын
What’s the part#?
@taingTv Жыл бұрын
U have to check with ur local dealer usually only for 4 cylinders not v6
@trsery9 ай бұрын
@@taingTvseems to be common issue with these cars in this year range, thanks for sharing! Have a 2014 with same problem.. .shaft/axle broke and no paint/corrosion etc like shown here.
@cbozz7063 Жыл бұрын
how are you working at a honda service center and dont have a ball joint separator .. just wacking away at it with a hammer isnt a good idea
@taingTv Жыл бұрын
U tell me a better tool to take this ball joint off i will pay ya
@GhadSpeed Жыл бұрын
Wacking it is pretty common lol
@lyfethusfar2759 ай бұрын
I have a ball joint kit very expensive and nice does not work for this pos
@teenice8944 ай бұрын
My 3lb hammer has been my ball joint separator for 10+yrs.. it has never failed me or damaged anything. Now if I'm replacing the ball joint I might grab my pickle fork if it's close by...