Thanks :-) (and sorry, sometimes we do use background music :-))

Good to hear :-)

Not the prettiest but if it works it works :-). We also made a video of how to make one yourself kzfaq.info/get/bejne/qJ10a8eW3cW3oZs.html

Retrofitlab.com thanks for the link that’s awesome.

@@kalei43 Good luck and be careful :-)

Maybe in the future :-)

Its the same exact thing for 04-05

@@Rone8Eleven Nice!

gracias :)

What wss the size ofyour projector

Thanks!

Did u find any vdo for black out??

Adeel Shahzad Bohaut sari hain KZfaq pe

We would recommend to use a bi-xenon or b-led projector instead of plug and play xenon or led bulbs.. :) for example the Aharon optimus TR. For the H4 bi-xenon function on a projector we have H4 cables with outputs to the ballasts and projector for hi/low www.retrofitlab.com/en/aharon-optimus-tr-bi-xenon-projectors-1.html

It can be adjusted like before. That's the entire reason for mounting it in the existing reflector.

***** Keep up the good work! Would love to see the headlights on the car

TA!

No me gustó la apariencia, todo negro

Lo mas seguro es que usara bombillas leds blancas en las luces direccionales y no quiere amarillo.

Hi, the box is used an oven to heat the headlight. A large cardboard box is used where hot air is blown through a heatgun. Make sure that the hot air of the heatgun does not blow directly to the headlight, place the headlight on small elevations so that the air can circulate properly through the box. We use a setting of 300 Degrees Celsius for 12-18 minutes / 1st lowest setting, depending on the size of the headlight.

@@Retrofitlab ok thanks i need practice this in my headlights, congratulations very nice work,see you in the next video

Stick the housing in the oven at like 250 for about 7 minutes will have the same results. Just be sure you put the headlight on a couple 2x4s and make sure it’s in the center of the oven.

Usually it can be done with normal paint from a spray can. But you can also use heat resistant paint, this usually has a nice flat finish. The pro's also use automotive grade 2k spray spaint.

Thank you 🙏

+Retrofitlab well its gonna suck having to epoxy the projector right the first time. I have to trim the back a bit since it wont screw like yours. i found the how to nut didn't mention adjustment.

But for 2.5 inch are necessary ?

Sorry English maybe? Google translate can't make much of it :)

We used a primer first :)

Para la 'shroud' utilizamos una 'herramienta giratoria / rotary tool / dremel'

great brother, thanks. what about the blub what type can be fixed .. I bought this bulb www.lazada.com.my/2x-led-h49003-headlight-lighting-16000lm-160w-conversion-bulb-beam6000k-ld912 17248395.html?Orderconfirmation&Email&LineItem if that bulb cant then should be this bulb? www.lazada.com.my/80w-cree-led-h8-bulb-angel-eye-halo-light-for-bmw-e90-e92-e82-e60e70-x5-e71-e89-8974544.html?mp=1 sorry I am not sure the links will work or no :)

David Cardenas That’s definitely a lot, how much were the parts?

This is Koito Q5 projectors. Like mine.

The best way is to connect the ballast with this cable: www.retrofitlab.com/en/wires/h4-diode-1.html

Ok now imma make mines ;-) thank you for the video

Do I have to change the 9006 bulbs to h4?

No they won't. You need to trim them in order to make them fit.

Thanks!! :) Maybe later, will keep it in mind!

Sorry we did not perform this retrofit yet..

its literally plug and play with the morimoto kit

The projectors are identical, there is no left or right side :)

In general, 2 methods are used, with both methods, be careful and patient. Method 1 is using a regular oven. Preheat the oven at 200 degrees Celsius. When ready, switch off the oven and place the headlight inside. Make sure that the headlight is not touching any metal of the oven by placing a cloth over the grid, for example. Leave the headlight in the oven for 10-15 minutes before opening it. If the headlight kit is not yet soft enough, put the headlight in the oven for a bit more time. Method 2 is suitable for larger headlights that do not fit in a regular oven, or if your lovely wife absolutely does not allow car parts to be baked in her kitchen. A large cardboard box is used where hot air is blown through a heatgun. Make sure that the hot air of the heatgun does not blow directly to the headlight, place the headlight on small elevations so that the air can circulate properly through the box. We use a setting of 300 Degrees Celsius for 12-18 minutes / 1st lowest setting, depending on the size of the headlight.

Thanks :-)

We don't advise to use LED bulbs in the projector because light output and pattern is usually quite bad. Examples here; www.retrofitlab.com/blog/h1-led-versus-xenon-mini-h1-projector/

It is ok.. Just don't heat them for too long :)

thank you

I'm straight lol . but its a very good look :)

Thanks! :-)

Hate to bother you again, I wanna know what cylindrical item did you use where you placed the heat gun? And what items did you use to hold the headlight in place inside the box? I saw previous comments where you’re emailing people about how to make the box can I get those instructions too? Highly appreciated thanks :)

Thanks a lot 👍🏻, love your videos btw.

For low and high beam it won't, because the Aharon bi-xenon projector is used and the reflector part isn't used to reflect the light anymore.

Thank you for the reply. I thought so but I wasn’t sure. You cleared all my doubts. Thank you.

Hi it is 2.5 projector

Is 3.0 fit in thjs

No, the bi-xenon projector can't hold H4 halogen bulbs. The high beam function is handled by the projector instead of the the bulb.

What bulbs are used?

From a retrofit company, like us, www.retrofitlab.com :-) Please contact us to order.

Please see this link: www.retrofitlab.com/en/accessories/butyl-rubber-sealant.html

Mini D2S projector: www.retrofitlab.com/en/aharon-mini-d2s-bi-xenon-projectors-30-1.html

Thank you

Thanks :-)!

Perhaps in the future :) Please stay tuned to our KZfaq channel!

Normally a heat resistant paint or even normal paint can be used, but preparation etc is dependant on the the specs by the manufacturer of the paint.

They are sprayed black if that is what you mean :-)

We do not have a result picture of this, sorry!

+Retrofitlab What about the shroud?

+Retrofitlab thanks. looked like it fit well in the housing. what ballast and bulb combination do you know of for highest light output(oem wise)?

+Retrofitlab okay thanks! Nice vid btw

thank you for your response, ok i will try that this coming weekend, i have already retrofit ready to install.. 👍👍👍

And the clips connect to the fixture that is to be mounted correct?